Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

ISTA P 2.51.3 VM
09-04-2014, 06:49 AM,
Post: #141
RE: ISTA P 2.51.3 VM
(07-04-2014, 17:46 PM)beemerboy88 Wrote:  
(07-04-2014, 17:34 PM)Dren1977 Wrote:  
(07-04-2014, 17:21 PM)beemerboy88 Wrote:  I've made new English snapshot that supports ICOM A Clone & ICOM A2 Clone.

I've also modified the snapshot so it'll work with ICOM emulator V3.1 from my other thread [change network adaptor 1 from bridged to custom(vmnet2) if using the emulator].

Notes:

1. delete all other snapshots before using this one.
2. parentCID of snapshot ISSS-000001 needs to match CID code of your main ISSS.vmdk disk (see post #23 for help if needed).
3. Does not work with original OEM ICOMs.

So can I use this with OPS?

Yes. The original Russian snapshots in the torrent didn't support OPS or ICOM A2 clone. Also ENET had problems. Because I have created new snapshot you can now use the ICOM emulator V3.1 for OPS and ENET (and K+DCAN if you want). So to clarify, this one snapshot will work with:

ICOM A Clone
ICOM A2 Clone
K+DCAN, OPS, OPPS & ENET (via ICOM emulator V3.1. http://garage-automotive.com/showthread.php?tid=3232).

@beemerboy88

I downloaded the ICOM EMULATOR SNAPSHOTS V3.1 from the links provided, Thanks.

Quick question, Do I need to add the ISTA EMULATOR MOD V3.1?

Im assuming that it pertains only to the other posts VM.
Quote this message in a reply
09-04-2014, 08:34 AM,
Post: #142
RE: ISTA P 2.51.3 VM
(09-04-2014, 06:49 AM)makp619 Wrote:  
(07-04-2014, 17:46 PM)beemerboy88 Wrote:  

@beemerboy88

I downloaded the ICOM EMULATOR SNAPSHOTS V3.1 from the links provided, Thanks.

Quick question, Do I need to add the ISTA EMULATOR MOD V3.1?

Im assuming that it pertains only to the other posts VM.

Mod is not needed.
Quote this message in a reply
09-04-2014, 09:29 AM,
Post: #143
RE: ISTA P 2.51.3 VM
I tried again with a E87 1er, 12/2009 (no 7/8 pin).

- Changed cable mode to D-Can + PT-Can with dcan.exe (...Done)
- Started ifhsrv32.exe after plugged in cable

As that didn't worked and I still have the same problem like in Post #134
   
I changed to the new snapshots in Post #136 and downloaded the ICOM Emulator.

- Started ICOM Emulator VM + ISSS VM
- Networks settings (vmnet2/Host-only) configured
- Installed driver in ICOM VM
- Set COM Port to 9, Latency 1
- Changed D-Can mode with DCAN.exe to D-Can+PT-Can (...Done)
- Started ifhsrv32.exe in ICOM Emu VM

I can see the ICOM in ISTA (Network O.K) but the "VIN could not be read from vehicle" - Error stays the same.

Just to be sure; the ignition has to be on, true?
Quote this message in a reply
09-04-2014, 11:22 AM,
Post: #144
RE: ISTA P 2.51.3 VM
(09-04-2014, 09:29 AM)goll89 Wrote:  I tried again with a E87 1er, 12/2009 (no 7/8 pin).

- Changed cable mode to D-Can + PT-Can with dcan.exe (...Done)
- Started ifhsrv32.exe after plugged in cable

As that didn't worked and I still have the same problem like in Post #134

I changed to the new snapshots in Post #136 and downloaded the ICOM Emulator.

- Started ICOM Emulator VM + ISSS VM
- Networks settings (vmnet2/Host-only) configured
- Installed driver in ICOM VM
- Set COM Port to 9, Latency 1
- Changed D-Can mode with DCAN.exe to D-Can+PT-Can (...Done)
- Started ifhsrv32.exe in ICOM Emu VM

I can see the ICOM in ISTA (Network O.K) but the "VIN could not be read from vehicle" - Error stays the same.

Just to be sure; the ignition has to be on, true?

Ignition needs to be on.

So did the led on your cable flash when you started the test?. It should start to flash green when ISTA/P tries to connect (Please answer this question).

Check in the ICOM vm that you have up to date drivers installed - 2013/2014. I assume when you installed the cable, afterwards you disconnected it from the vm and then reconnected it again so driver change/com port change takes effect (also when unplugging, right click on the dcan usb icon and select disconnect(connect to host). Then unplug. If you just pull it out without doing that it can cause communication/driver errors). Also when you have installed the cable take a new snapshot so that it doesn't ask you to install the drivers again next time.

Best to use a USB2 port (not USB3). VMware has problems with USB3.

Have you tested your cable using other software to make sure it works ok?. i.e test with inpa, Rheingold or ista/d on the e87.

I used the software recently on 2008 E87 and it worked.
Quote this message in a reply
09-04-2014, 20:01 PM,
Post: #145
RE: ISTA P 2.51.3 VM
Hello,

I'm wondering how can I exit the ISTA/P so I can set up PASS THRU/PTT drivers/ediabas? Anyone played with that (I have it working natively in Rheingold)?

Any info would be appreciated!
Quote this message in a reply
11-04-2014, 01:42 AM,
Post: #146
RE: ISTA P 2.51.3 VM
(09-04-2014, 20:01 PM)MMehanik Wrote:  Hello,

I'm wondering how can I exit the ISTA/P so I can set up PASS THRU/PTT drivers/ediabas? Anyone played with that (I have it working natively in Rheingold)?

Any info would be appreciated!

What version do you have?

If it is like the previous versions where it boots up at power on and you are unable to access windows you need to run soft like konboot to change login. Login and add all drivers you need.
Quote this message in a reply
11-04-2014, 06:42 AM,
Post: #147
RE: ISTA P 2.51.3 VM
(09-04-2014, 11:22 AM)beemerboy88 Wrote:  
(09-04-2014, 09:29 AM)goll89 Wrote:  I tried again with a E87 1er, 12/2009 (no 7/8 pin).

- Changed cable mode to D-Can + PT-Can with dcan.exe (...Done)
- Started ifhsrv32.exe after plugged in cable

As that didn't worked and I still have the same problem like in Post #134

I changed to the new snapshots in Post #136 and downloaded the ICOM Emulator.

- Started ICOM Emulator VM + ISSS VM
- Networks settings (vmnet2/Host-only) configured
- Installed driver in ICOM VM
- Set COM Port to 9, Latency 1
- Changed D-Can mode with DCAN.exe to D-Can+PT-Can (...Done)
- Started ifhsrv32.exe in ICOM Emu VM

I can see the ICOM in ISTA (Network O.K) but the "VIN could not be read from vehicle" - Error stays the same.

Just to be sure; the ignition has to be on, true?

Ignition needs to be on.

So did the led on your cable flash when you started the test?. It should start to flash green when ISTA/P tries to connect (Please answer this question).

Check in the ICOM vm that you have up to date drivers installed - 2013/2014. I assume when you installed the cable, afterwards you disconnected it from the vm and then reconnected it again so driver change/com port change takes effect (also when unplugging, right click on the dcan usb icon and select disconnect(connect to host). Then unplug. If you just pull it out without doing that it can cause communication/driver errors). Also when you have installed the cable take a new snapshot so that it doesn't ask you to install the drivers again next time.

Best to use a USB2 port (not USB3). VMware has problems with USB3.

Have you tested your cable using other software to make sure it works ok?. i.e test with inpa, Rheingold or ista/d on the e87.

I used the software recently on 2008 E87 and it worked.

I already tried with INPA a few days ago (when everything was fine).
As it didn't work with ISTA / ICOM EMU I tried again today - now I get the Error "IFH 0009 No Response From Control Unit" in INPA.
Looks like I have a crappy cable - will order a "better" one and check again.
Quote this message in a reply
15-04-2014, 17:01 PM, (This post was last modified: 15-04-2014, 20:58 PM by Faisc@.)
Post: #148
RE: ISTA P 2.51.3 VM
(11-04-2014, 01:42 AM)makp619 Wrote:  What version do you have?http://garage-automotive.com/cometchat/.http://garage-automotive.com/images/default_avatar.gif

If it is like the previous versions where it boots up at power on and you are unable to access windows you need to run soft like konboot to change login. Login and add all drivers you need.

Hello,

thanks for the info. I'm using version posted in here and beemerboys snapshots. But if I try to reboot I get the no USB Flash dongle error (as it's the protected) - so I don't know how to change the password/exit the program.

Any ideas on how this can be done, anyone? Thank you!

EDIT: I found http://forums.bimmerforums.com/forum/sho...ion-how-to and if I'm not mistaken the error message says that th usb flash drive has to be present on this VM - so I guess this could work for someone that has the usb key?
Quote this message in a reply
15-04-2014, 20:25 PM, (This post was last modified: 15-04-2014, 20:58 PM by Faisc@.)
Post: #149
RE: ISTA P 2.51.3 VM
Deleted.........
Quote this message in a reply
16-04-2014, 16:23 PM,
Post: #150
RE: ISTA P 2.51.3 VM
(15-04-2014, 17:01 PM)MMehanik Wrote:  
(11-04-2014, 01:42 AM)makp619 Wrote:  What version do you have?http://garage-automotive.com/cometchat/.http://garage-automotive.com/images/default_avatar.gif

If it is like the previous versions where it boots up at power on and you are unable to access windows you need to run soft like konboot to change login. Login and add all drivers you need.

Hello,

thanks for the info. I'm using version posted in here and beemerboys snapshots. But if I try to reboot I get the no USB Flash dongle error (as it's the protected) - so I don't know how to change the password/exit the program.

Any ideas on how this can be done, anyone? Thank you!

EDIT: I found http://forums.bimmerforums.com/forum/sho...ion-how-to and if I'm not mistaken the error message says that th usb flash drive has to be present on this VM - so I guess this could work for someone that has the usb key?

Here is the Admin password for it. I dont know if it will still help you.

ISPI V3.0 & V3.1
User: Administrator
Password: Wh3dWvdU9?Cw1234


ISPI V2.9
User: Administrator
Password: DnAPfdI2.8.0mgasuskSuUe.
Quote this message in a reply


Possibly Related Threads…
Thread Author Replies Views Last Post
XZBMW ISTA Standalone Licenserequest up to v4.37.4x Sedoy 8,649 627,819 1 hour ago
Last Post: JPToadstool
  ista 4.46 Standalone kiranabc 33 3,067 Yesterday, 19:51 PM
Last Post: Siki78
  ista for use whit vcx se db8000 0 41 Yesterday, 15:28 PM
Last Post: db8000
  AOS Ista possible to deactivate second check after scan? RaoulK1998 17 363 Yesterday, 10:39 AM
Last Post: RaoulK1998
XZBMW ISTA 4.46.xx problems and possible solution Sedoy 76 7,373 27-03-2024, 20:02 PM
Last Post: Node
XZBMW Update ISTA at once 4.43.40 (ISTA Update Program) charlesjyw 34 6,485 27-03-2024, 10:39 AM
Last Post: MINIGP1610
XZBMW BMW ISTA-P Rheingold 69.0.200 (Torrent File) carsoftcare 1 129 26-03-2024, 12:09 PM
Last Post: hlip
  ISTA launcher problem Red_bean_bun 1 168 26-03-2024, 05:11 AM
Last Post: 2013m5
XZBMW Adding a new vehicle/model to "Reingold" ISTA+ dieselweasel 12 669 25-03-2024, 08:11 AM
Last Post: Node
XZBMW Ultimate Ediabas/ISTA+ voltage control V3 Node 322 121,514 24-03-2024, 23:45 PM
Last Post: armenh7

Forum Jump:


Users browsing this thread:
2 Guest(s)

Return to TopReturn to Content