[Node]

If using VPN:

On car side ediabas.ini set to std:obd and ifhsrv32 started, firewall port 6801 opened. On ISTA/INPA side ediabas.ini set to remote with the ip address the car side gets on VPN connection.

[Wibbles]

with DCAN you need to configure ediabas on both ends + start IFH server on the client (car side), setup VPN and take both firewalls down.

In ISTA, configure connection via ediabas.

So this means, on both sides EDIABAS.INI set to the same IP for example 192.168.68.1 with Port 6801, both sides set to STD:OBD, VPN Connection via TeamViewer, start ifhsrv32.exe on the Car Side, and then I should be able to use the BMW Standard Tools on my End?

No, on your side Ediabas should be set to REMOTE and RemoteHost: VPN IP

In Car side, just set to STD:OBD & run IFH Server

[AbelF10]

with DCAN you need to configure ediabas on both ends + start IFH server on the client (car side), setup VPN and take both firewalls down.

In ISTA, configure connection via ediabas.

So this means, on both sides EDIABAS.INI set to the same IP for example 192.168.68.1 with Port 6801, both sides set to STD:OBD, VPN Connection via TeamViewer, start ifhsrv32.exe on the Car Side, and then I should be able to use the BMW Standard Tools on my End?

No, on your side Ediabas should be set to REMOTE and RemoteHost: VPN IP

In Car side, just set to STD:OBD & run IFH Server

hy with this setup on ista iff you select icom doesent work. so when open ista select ediabas or witch one? thanks

[Maxine315]

with DCAN you need to configure ediabas on both ends + start IFH server on the client (car side), setup VPN and take both firewalls down.

In ISTA, configure connection via ediabas.

So this means, on both sides EDIABAS.INI set to the same IP for example 192.168.68.1 with Port 6801, both sides set to STD:OBD, VPN Connection via TeamViewer, start ifhsrv32.exe on the Car Side, and then I should be able to use the BMW Standard Tools on my End?

No, on your side Ediabas should be set to REMOTE and RemoteHost: VPN IP

In Car side, just set to STD:OBD & run IFH Server

hy with this setup on ista iff you select icom doesent work. so when open ista select ediabas or witch one? thanks

Is there a way to hook bmw explore remotely

[Wibbles]

with DCAN you need to configure ediabas on both ends + start IFH server on the client (car side), setup VPN and take both firewalls down.

In ISTA, configure connection via ediabas.

So this means, on both sides EDIABAS.INI set to the same IP for example 192.168.68.1 with Port 6801, both sides set to STD:OBD, VPN Connection via TeamViewer, start ifhsrv32.exe on the Car Side, and then I should be able to use the BMW Standard Tools on my End?

No, on your side Ediabas should be set to REMOTE and RemoteHost: VPN IP

In Car side, just set to STD:OBD & run IFH Server

hy with this setup on ista iff you select icom doesent work. so when open ista select ediabas  or witch one? thanks

Is there a way to hook bmw explore remotely

Never tried but even if you could, they may ban your account based on ENET latency - seen some tuning app companies do that, so beware.

[juantg93]

I do the remote connection like this:

Mi ediabas is version 7.3.0 and I use TeamViewer, is for ENET cable.

1. I open normal conection with remote laptop. I send remote enet and install vpn controller in her teamviewer settings. Then I activate remote enet and close conecion.

2. I open conection with team viewer too but as vpn. I copy ip of client and paste in ediabas.ini.
In mi ediabas i have:
INTERFACE = ENET
#Interface = REMOTE

I paste ip of client in "TCP: Remote Host" and "XEtherne:Remote Host". Is only necesary write ip in one option, but I'm not sure which option it is, so I always paste it in two options.

The remote conection are ready. In esys you have to click in "Connection via gateway URL: tcp://(here you paste vpn ip of client):6801" For example: tcp://7.164.211.65:6801

In ista you have to set in Vehicle Interface settings "Ediabas default settings"

I always do these four steps and it works perfectly for me.

[DarkSide]

So this means, on both sides EDIABAS.INI set to the same IP for example 192.168.68.1 with Port 6801, both sides set to STD:OBD, VPN Connection via TeamViewer, start ifhsrv32.exe on the Car Side, and then I should be able to use the BMW Standard Tools on my End?

No, on your side Ediabas should be set to REMOTE and RemoteHost: VPN IP

In Car side, just set to STD:OBD & run IFH Server

hy with this setup on ista iff you select icom doesent work. so when open ista select ediabas  or witch one? thanks

Is there a way to hook bmw explore remotely

Never tried but even if you could, they may ban your account based on ENET latency - seen some tuning app companies do that, so beware.

Hello. how can i get your remote connection tool? car connector for bmw