Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

Opcom firmware
16-08-2017, 09:15 AM, (This post was last modified: 16-08-2017, 09:34 AM by gyenge.)
Post: #1
Opcom firmware
I have Opcom v5 hq clone and i'm trying to run with software 131223e RO. I changed ept from FTDI from V2 to B2 and change manual serial Number from OP to FT.

When i start software tell me to connect the interface or to install the driver USB. After i change EPT show me another error "interface with incompatible firmware version. Please contact your supplier for more information."

My firmware version is 1.64

Some tips from someone ??

ANyone HAad firmware fw160 . i thinking this i need
Quote this message in a reply
[+] 1 user says Thank You to gyenge for this post
16-08-2017, 18:40 PM, (This post was last modified: 16-08-2017, 18:41 PM by mattydr67.)
Post: #2
RE: Opcom firmware
Forget about. Its protected solution.
If you wanna use that software you need to buy a tool that its allready made for it.
By the way. The firmware used in 131223e RO is fw1.60
Good luck
Quote this message in a reply
[+] 2 users say Thank You to mattydr67 for this post
21-08-2017, 13:15 PM,
Post: #3
RE: Opcom firmware
I know that . Do u have fw160 or ept file?
Quote this message in a reply
21-08-2017, 13:33 PM,
Post: #4
RE: Opcom firmware
(21-08-2017, 13:15 PM)gyenge Wrote:  I know that . Do u have fw160 or ept file?

Hi gyenge

ipls if help u this fw 1.60 try,if help u use magic buttons,pw pm

BR asto


Attached Files
FW 1.60 Bootloader.rar
File Type: .rar
Downloaded: 451 times
Size: 19.15 KB


underX-Tool Superprog & Upd.2022 for sale!!PCR2.1 PIN,KM,CS,MAC1,MAC2,ImmoOFF,Iaw59F Dec.Tool,BMW,MB,Renault CAN filter,Immo Off-CRC calc.,BMW Fxx-Exx Alfa 159 Original Keys,Nissan LCN Nav Dec. OMAP mcu,RCD310-510 decode or code off.Calculate JCB v1-v2,VW Comfort CS,PIN,MAC from dump,EGR-DPF-Lambda OFF
Reputation: +4 - AIR0 [+1] , bounce24 [+1] , Kenny [+1] , mcsabus [+1]
Quote this message in a reply
[+] 20 users say Thank You to asto for this post
21-08-2017, 18:31 PM, (This post was last modified: 21-08-2017, 19:26 PM by mattydr67.)
Post: #5
RE: Opcom firmware
(21-08-2017, 13:15 PM)gyenge Wrote:  I know that . Do u have fw160 or ept file?
The firmware and ept will not help you either
Good luck
Quote this message in a reply
24-08-2017, 06:19 AM,
Post: #6
RE: Opcom firmware
Need the old dump for ftdi and works but i dont know alghorithm to create it smile
Quote this message in a reply
28-08-2017, 10:23 AM,
Post: #7
RE: Opcom firmware
To make a copy of the FW of the HQ clone you can with OCFLASH:
1 Connect HQ hardware to PC
2 Open the flash and press "Device file" and save.
If we want to recover the file to record it we do the following:
1 Press "File Device" and it will automatically be recorded ..
Important: Never copy the "ept" with Mpro, to record on the hardware HQ
Quote this message in a reply
28-08-2017, 11:23 AM, (This post was last modified: 28-08-2017, 11:29 AM by mattydr67.)
Post: #8
RE: Opcom firmware
Device to File = FTDI_xxxxxxxx.ocfd
File to Device = HQ_xxxxxxxx.bin
Take care what you do
OCFLash can only flash the firmware but cannot read it ( firmware is from Pic18F458 not ftdi )
Good luck
Quote this message in a reply
28-08-2017, 12:42 PM,
Post: #9
RE: Opcom firmware
What I mean is that it is very important to have a backup copy of the HW opcom HQ, both the user and the vendor and you can carry out the recovery with Ocflash and thus avoid future problems and of course avoid buying another HQ. What happens when you mistakenly make your device unusable? In this case the backup of yours or that of the provider recovers the interface. I have complied, in any case making a backup does not spoil the device and avoid spending again.
Quote this message in a reply
28-08-2017, 14:04 PM, (This post was last modified: 28-08-2017, 14:12 PM by mattydr67.)
Post: #10
RE: Opcom firmware
"If you mistake".... what this is mean?
In my opinion you need the bin file to flash it back as a backup not the ocfd file.
If your ftdi chip will be defective and even you have the backup bin file this will be unusefull.
If your Pic18F458 is defective then just replace it and reflash with any firmware version. Then you can use the OCflash.
I don't see any reason to make a back up.
But if you then be my guest.
Good luck

P.S. - if you have any problems with your HQ cline then contact your supplier. He will help you in any way
Quote this message in a reply


Possibly Related Threads…
Thread Author Replies Views Last Post
KVauxhall HMI 2.0 USB firmware 23228506 need miriaga4344 0 124 24-11-2023, 11:59 AM
Last Post: miriaga4344
  OPCOM "NEW" V1.99 does not communicate with ESC (ECU does not reply, please wait 2 se lim0nade 30 8,268 20-03-2022, 17:01 PM
Last Post: mattydr67
  Opcom Motherboard version (can't find USB drivers) BrainBT 5 1,364 17-10-2019, 17:18 PM
Last Post: skyline
  Opcom Bootloader Repair with TL866 ICSP port aki1 3 1,622 07-10-2019, 13:07 PM
Last Post: avepla
  Opcom HQ Installers 2017 Gabriel87 18 10,349 30-09-2019, 22:30 PM
Last Post: AIR0
  opcom clone need help to repair autosolutions 1 814 18-09-2019, 02:40 AM
Last Post: mattydr67
  OPCOM problem conecting CrossMan 22 5,282 02-08-2019, 05:18 AM
Last Post: mattydr67
KOpel OPCOM china for win7 or win10 josef1708 7 4,520 26-06-2019, 22:27 PM
Last Post: MartinB
KOpel Solved! Opcom V1.99 communication error irarkh 23 30,903 07-05-2019, 06:40 AM
Last Post: Sirius83
KOpel Software Opcom Hq v12, v13 ,v15 and Vaux com v13, v16 McMihai 19 12,711 30-12-2018, 22:56 PM
Last Post: Moldovan1

Forum Jump:


Users browsing this thread:
2 Guest(s)

Return to TopReturn to Content