[playaz187]

Hi everyone!

I have a problem.I refreshed the navi,everything goes well.But if i turn on the Google earth,the navi put me to middle of the Pacific Ocean When i turn off,everything is ok.Ideas?

drive some kms

[benyclaudiu]

Good colleagues everywhere
Does anyone know how to fix this problem: 16367 - Module Control - Error in Flash-ROM
I tried to get rid of it by blowing and reinstalling all the sucessful software, but the error still stays there.
It reinstalled through the Emergency Update starting with the k0022_2 software error was still, I reinstalled all the software up to ko257_6_D1 the error still remained I deleted and formatted hdd from the hidden menu and reinstalled the maps then I activated the maps, everything works normally.
The error still exists when scanning, an idea how to get rid of this error?
If they are colleagues who struck me with this error, they can tell us how they managed to get rid of them.
Thank you
Address 5F: Information Electr. Labels: 4E0-035-6xx-5F.clb
Control Module Part Number: 4E0 035 666 K HW: 4E0 035 666 B
Component and/or Version: H-BN-EU H41 0187
Software Coding: 010100010102E1ED03000706E10302030001
Work Shop Code: WSC 02391 823 56573
VCID: 2E55787F79D87351CD7-807B
Fault Codes have been Erased

1 Fault Found:
16367 - Control Module - Error in Flash-ROM

[robot1]

After a map update mate?
After a Firmware Update ok,but map?

Try to do this update again user definided

[destroi35]

Hello please an advice please:

i have 2016 maps( 6.22.4 ) on my navi 3GP with GEMMI activated and 767firmware.
can i update direct to 942.3 firmware and direct to the maps: 6.25.3 ?

any help please .... i apreciate

[playaz187]

Hello please an advice please:

i have 2016 maps( 6.22.4 ) on my navi 3GP with GEMMI activated and 767firmware.
can i update direct to 942.3 firmware and direct to the maps: 6.25.3 ?

any help please .... i apreciate

yes u can

[rafaell68]

Hello,

I have problems with 6.25.3 map update.
I had a 3G+ with K942 + 6.24.2.
I thought it was enough to just load new 6.25.3 maps.

I put the card with 6.25.3 and in engineering menu it shows that only "Map Styles" are to update.
I decided to delete nav/databaseupdate and nav HDD partition as described in the tutorial.
After this update map was running correctly, but after I had this :


Are these problems with activation?
I put my activation card but it shows that maps are already activated.
So i put uninstall card and it run correctly. After this i put activation card but it still shows that i need to uninstall old activation.
What am I doing wrong?

[darkdll]

@rafaell68 you must do an user defined mode update. Check the manual and when you’re in installation check all navi sections.

[ppsvara]

[quote='rafaell68' pid='297289' dateline='1511169869']


I would like to remind you firmware for audi A4,A5,Q5,Q7 is differently like firmware for Q3,A6,A7,A8..
check or use the right one

[rafaell68]

[quote='rafaell68' pid='297289' dateline='1511169869']


I would like to remind you firmware for audi A4,A5,Q5,Q7 is differently like firmware for Q3,A6,A7,A8..
check or use the right one

I know. But i will update only maps by user define mode. I already got K942.

[ppsvara]

I would like to remind you firmware for audi A4,A5,Q5,Q7 is differently like firmware for Q3,A6,A7,A8..
check or use the right one

[/quote]I know. But i will update only maps by user define mode. I already got K942.
[/quote]

I do not think the problem is in activation. because
the navigation data is not blocked!