[number7]

I've just tried AVDI DUMP + transponder codes - doesn't started.
But ZED-BULL didn't program transponder at all. pg1, pg2, pg3 was programmed corectly, but in pg4 is 00000000. When I put 02010000, after reading is 0000000.

[raffy haddad]

Can you post the transponder data
And page 4 keep it 00000000 it is a secret key it will not show you the data
Only by special tools unfortunaly that i don’t have
First did you put back original eeprom dump ?
Did you program transponder as the last post i gave you ?

[number7]

What tool do you have as programmer and key reader programmer
Regards

---

What tool do you have as programmer and key reader programmer
Regards

do you have a transponder programmer ?
please put this file in eeprom
and program 4d transponder or tpx2
pg1 FF
pg2 05
pg3 A6F76601
pg4 0201000000
and report
regards
if that does not work be patient i will do my best to help you
please report

That is what I have done

---

I heard something about ATMEL 93c66 that it has to be ereased couple of times to be programmed. But when I wrote it, then readed it it was correct. But when I read it after connecting to bike there was many difrents.
I'm wondering of putting original DUMP and programming CN2 to values which are in DUMP...

[raffy haddad]

Hello number 7
In post you have read 93c66 as 8bit and 16 bit
Please put original dump as 16 bit in eeprom and don’t change anything
The original one 16 bit
And check post #16
And put data to transponder as i gave you in post 16
And try it it should work 100%
Regards

[number7]

I have tried but motor didn't start.
I have tried many options to program as master 0A or slave 05 trying many adresses from file - nothing.

I'm wondering if there is a difrent in 4D60 and 4D62, becouse my CN2 is programmed as 4D60 and I coannot program it as 4D62.

[raffy haddad]

I have tried but motor didn't start.
I have tried many options to program as master 0A or slave 05 trying many adresses from file - nothing.

I'm wondering if there is a difrent in 4D60 and 4D62, becouse my CN2 is programmed as 4D60 and I coannot program it as 4D62.

Hello
Ofcourse there is difference between 4d60 and 4d62
You should make it 4d62 first then program transponder pg1and pg2 and pg3
With data in post #16
Cn2 can be programmed manytimes don’t worry about
And don’t forget to put back original dump as 16 bit to eeprom

In avdi tagtool transponder production you find kawazaki id 62 programm it
Regards
Here you a imade for you a transponder
See picture

[number7]

OK - I made transponder as You said - 4D62 FF 05 A6F76601 and..... nothing - motor didn't start.
Now I think about changing 93c66 to another 93c66

[raffy haddad]

Hello freind
The transponder in post 16 different that you program it
Here they are
Pg1 FF
Pg2 05
Pg3 667F8E0C
Pg4 keep it 00000000000
And put original file as you read in 16 bit back to eeprom
Please read carfully
Did you look to picture i sent you ?
As long as you can read and write eeprom that mean it is good no need to change

[number7]

Sorry - I wrote A6F76601 but I mean 667F8E0C

I'm wondering if it is secound key adress. Tomorow I will check adresses where Key can be.

[raffy haddad]

Hello
Yes it is slave key
But give answer did you put back original file to eeprom as 16 bit ?