[dave1982]

Hello
My brother have the same car
And have same problem
And gave us a head illness
The problem was the brake lamp
Where burn and the brake pedal switch was not in place
And even when you change them you must clear fault code to start and to f letter go away
Even the dealer says that the easytronic ecu must be replaced
Only the problem was in brake pedal switch
And brake lamp was burn
And fvdi read almost the same troubles that you have
F letter in dask means something wrong in car it can not start
Regards

Yes I do agree with this post fix the brake light switch fault first and go from there

thanks for all your help.
Sorry for my late answer.
I changed the brake switch (buyed a "Hella") but still not changes with all this fault codes.

[darek_naprawa]

Make tests and adaptations. Easytronic.

[dil6222]

Where you from Dave ? And what are you using to program ? if using opcom use 1.59 firmware also now you know bulb is good clear all units of faults try start then scan again to see what faults reoccur then start from there I also had the vin not programming fault on corsa c had to reset all units and reprogram 1 by 1.

[dave1982]

Where you from Dave ? And what are you using to program ? if using opcom use 1.59 firmware also now you know bulb is good clear all units of faults try start then scan again to see what faults reoccur then start from there I also had the vin not programming fault on corsa c had to reset all units and reprogram 1 by 1.

Im from munich (germany).
using china opcom (sry, dont know the FW)
yesterday i tried to clear the faults but they came back.
can you tell me if there is a special order in resetting and reprogramming the units?
and i still cant reset or program the speedometer.
everytime it fails. i tried it on other car (corsa c) and it worked so i think my opcom is working.
do you know which units are connected in the CAN-BUS?
i think that maybe there is something wrong.
i opened the cables from the the ECM and Easytronic to look if there is a problem, but was all good.
i saw that the CAN-BUS is from ECM to Easytronic and from Easytronic to BCM.
but i could only check half of the cable "easytronic to BCM" because the cable going under the windshield. do you think that maybe there is something wrong?
should i remove the whole cable with the BCM?

[Ashraf6119]

Can you post your full diagnostic report here lets see what fault code you still have and we go from there also if possible we can help you via Team Viewer...........

[dave1982]

Can you post your full diagnostic report here lets see what fault code you still have and we go from there also if possible we can help you via Team Viewer...........

is there a option in the opcom for a "full diagnostic report"?
here are the faultcodes:

BCM:
B3058 - (0) Vehicle ID Not Programmed - Present

ECM:
P1615 - (0) Wrong Vehicle ID from Body Control Module - Present
P1616 - (0) Wrong Vehicle ID from Instrument Control Module - Present
U2106 - (0) CAN-Bus no Communication with Transmission Control Module - Present
U2107 - (0) CAN-Bus no Communication with Body Control Module - Present

Easytronic (MTA):
P0725 - (4) Engine Speed Signal CAN-BUS Malfunction - Present
P0505 - (4) Idle Speed Signal CAN-BUS Malfunction - Present
P1895 - (4) Engine Torque Signal CAN-BUS Malfunction - Present
P1896 - (4) Eingine Torque Request CAN-BUS Malfunction - Present
P1120 - (4) Accelerator Pedal Position CAN-BUS Malfunction - Present
P1703 - (4) Brake Light Switch CAN-BUS Malfunction - Present
U2105 - (4) CAN-BUS no Communication with ECM (Engine Controle Module) - Present
P0110 - (4) Intake Air Temperature CAN-BUS Malfunction - Present
P0115 - (4) Engine Coolant Temperature CAN-BUS Malfunction - Present

[Ashraf6119]

Can you post your full diagnostic report here lets see what fault code you still have and we go from there also if possible we can help you via Team Viewer...........

is there a option in the opcom for a "full diagnostic report"?
here are the faultcodes:

BCM:
B3058 - (0) Vehicle ID Not Programmed - Present

ECM:
P1615 - (0) Wrong Vehicle ID from Body Control Module - Present
P1616 - (0) Wrong Vehicle ID from Instrument Control Module - Present
U2106 - (0) CAN-Bus no Communication with Transmission Control Module - Present
U2107 - (0) CAN-Bus no Communication with Body Control Module - Present

Easytronic (MTA):
P0725 - (4) Engine Speed Signal CAN-BUS Malfunction - Present
P0505 - (4) Idle Speed Signal CAN-BUS Malfunction - Present
P1895 - (4) Engine Torque Signal CAN-BUS Malfunction - Present
P1896 - (4) Eingine Torque Request CAN-BUS Malfunction - Present
P1120 - (4) Accelerator Pedal Position CAN-BUS Malfunction - Present
P1703 - (4) Brake Light Switch CAN-BUS Malfunction - Present
U2105 - (4) CAN-BUS no Communication with ECM (Engine Controle Module) - Present
P0110 - (4) Intake Air Temperature CAN-BUS Malfunction - Present
P0115 - (4) Engine Coolant Temperature CAN-BUS Malfunction - Present

And what fault codes you have in Instrument.........?

1)From the looks of your fault it looks like you BCM is been reset and could be not programed as it should be on the CAN System..

2) Also your BCM and the Instrument Cluster are not matching with your Engine ECU in this case ECU is not happy...

P1615 - (0) Wrong Vehicle ID from Body Control Module - Present
P1616 - (0) Wrong Vehicle ID from Instrument Control Module - Present...

As I said the best way to help you is to vis Team Viewer...

[dave1982]

Can you post your full diagnostic report here lets see what fault code you still have and we go from there also if possible we can help you via Team Viewer...........

is there a option in the opcom for a "full diagnostic report"?
here are the faultcodes:

BCM:
B3058 - (0) Vehicle ID Not Programmed - Present

ECM:
P1615 - (0) Wrong Vehicle ID from Body Control Module - Present
P1616 - (0) Wrong Vehicle ID from Instrument Control Module - Present
U2106 - (0) CAN-Bus no Communication with Transmission Control Module - Present
U2107 - (0) CAN-Bus no Communication with Body Control Module - Present

Easytronic (MTA):
P0725 - (4) Engine Speed Signal CAN-BUS Malfunction - Present
P0505 - (4) Idle Speed Signal CAN-BUS Malfunction - Present
P1895 - (4) Engine Torque Signal CAN-BUS Malfunction - Present
P1896 - (4) Eingine Torque Request CAN-BUS Malfunction - Present
P1120 - (4) Accelerator Pedal Position CAN-BUS Malfunction - Present
P1703 - (4) Brake Light Switch CAN-BUS Malfunction - Present
U2105 - (4) CAN-BUS no Communication with ECM (Engine Controle Module) - Present
P0110 - (4) Intake Air Temperature CAN-BUS Malfunction - Present
P0115 - (4) Engine Coolant Temperature CAN-BUS Malfunction - Present

And what fault codes you have in Instrument.........?

1)From the looks of your fault it looks like you BCM is been reset and could be not programed as it should be on the CAN System..

2) Also your BCM and the Instrument Cluster are not matching with your Engine ECU in this case ECU is not happy...

P1615 - (0) Wrong Vehicle ID from Body Control Module - Present
P1616 - (0) Wrong Vehicle ID from Instrument Control Module - Present...

As I said the best way to help you is to vis Team Viewer...

sorry, forgot to make a picture of the instrument fault codes but where was 3 faults:
some temperature sensor
ID not programmed
security not programmed

I programmed the "Merivas VIN" in BCM in another car and the fault code in the BCM
was gone.
But fault codes in ECM were still present.
And then i try to reset and program it in the meriva, the code came back.
Is it normal that the BCM has only the last 8 digits from the VIN?
Because i can not program the full VIN in the BCM.

Thanks for your help. I send you a message when i m at the car, so we can try it with team viewer.

[dil6222]

Can you post your full diagnostic report here lets see what fault code you still have and we go from there also if possible we can help you via Team Viewer...........

is there a option in the opcom for a "full diagnostic report"?
here are the faultcodes:

BCM:
B3058 - (0) Vehicle ID Not Programmed - Present

ECM:
P1615 - (0) Wrong Vehicle ID from Body Control Module - Present
P1616 - (0) Wrong Vehicle ID from Instrument Control Module - Present
U2106 - (0) CAN-Bus no Communication with Transmission Control Module - Present
U2107 - (0) CAN-Bus no Communication with Body Control Module - Present

Easytronic (MTA):
P0725 - (4) Engine Speed Signal CAN-BUS Malfunction - Present
P0505 - (4) Idle Speed Signal CAN-BUS Malfunction - Present
P1895 - (4) Engine Torque Signal CAN-BUS Malfunction - Present
P1896 - (4) Eingine Torque Request CAN-BUS Malfunction - Present
P1120 - (4) Accelerator Pedal Position CAN-BUS Malfunction - Present
P1703 - (4) Brake Light Switch CAN-BUS Malfunction - Present
U2105 - (4) CAN-BUS no Communication with ECM (Engine Controle Module) - Present
P0110 - (4) Intake Air Temperature CAN-BUS Malfunction - Present
P0115 - (4) Engine Coolant Temperature CAN-BUS Malfunction - Present

And what fault codes you have in Instrument.........?

1)From the looks of your fault it looks like you BCM is been reset and could be not programed as it should be on the CAN System..

2) Also your BCM and the Instrument Cluster are not matching with your Engine ECU in this case ECU is not happy...

P1615 - (0) Wrong Vehicle ID from Body Control Module - Present
P1616 - (0) Wrong Vehicle ID from Instrument Control Module - Present...

As I said the best way to help you is to vis Team Viewer...

sorry, forgot to make a picture of the instrument fault codes but where was 3 faults:
some temperature sensor
ID not programmed
security not programmed

I programmed the "Merivas VIN" in BCM in another car and the fault code in the BCM
was gone.
But fault codes in ECM were still present.
And then i try to reset and program it in the meriva, the code came back.
Is it normal that the BCM has only the last 8 digits from the VIN?
Because i can not program the full VIN in the BCM.

Thanks for your help. I send you a message when i m at the car, so we can try it with team viewer.

Correct it shows only last 8 digits.
you type full vin when programming but it changes it to last 8 this is normal

its seems you have can comms wire issue or are programming incorrectly
Reset bcm then program with security code and vin that match's all other units ecm immo etc then cycle ignition and clear faults then rescan and see if faults reoccur let us know
same for dash reset and reprogram then clear etc clear all units though not just the ones you have programmed.
I had same issues with corsa c and there was a split in can comms wire.