[hojo29]

What status has the address 63,62 and A0 at Tool32?

[russellg]

What status has the address 63,62 and A0 at Tool32?

Running apiJob("R56","flash_programmier_status_lesen_funktional","","")

returns :-

JOB_STATUS = OKAY
ECU_ADR = 62
ECU_GROBNAME = MOSTGW
ID_SG_ADR = 98 00 00 00 62 ...b
FLASH_PROGRAMMIER_STATUS_TEXT = Normalbetrieb
FLASH_PROGRAMMIER_STATUS = 1 00 01 ..
_TEL_ANTWORT = 7 Bytes
0000 : 83 F1 62 71 0A 01 4C ?ñbq..L


JOB_STATUS = OKAY
ECU_ADR = 63
ECU_GROBNAME = MASK/CCC
ID_SG_ADR = 99 00 00 00 63 ...c
FLASH_PROGRAMMIER_STATUS_TEXT = Normalbetrieb
FLASH_PROGRAMMIER_STATUS = 1 00 01 ..
_TEL_ANTWORT = 7 Bytes
0000 : 83 F1 63 71 0A 01 4C ?ñcq..L

JOB_STATUS = OKAY
ECU_ADR = A0
ECU_GROBNAME = CCC
ID_SG_ADR = 160 00 00 00 A0 ... 
FLASH_PROGRAMMIER_STATUS_TEXT = Normalbetrieb
FLASH_PROGRAMMIER_STATUS = 1 00 01 ..
_TEL_ANTWORT = 7 Bytes
0000 : 83 F1 A0 71 0A 01 4C ?ñ q..L

[hojo29]

What status has the address 63,62 and A0 at Tool32?

Running apiJob("R56","flash_programmier_status_lesen_funktional","","")

returns :-

JOB_STATUS = OKAY
ECU_ADR = 62
ECU_GROBNAME = MOSTGW
ID_SG_ADR = 98 00 00 00 62 ...b
FLASH_PROGRAMMIER_STATUS_TEXT = Normalbetrieb
FLASH_PROGRAMMIER_STATUS = 1 00 01 ..
_TEL_ANTWORT = 7 Bytes
0000 : 83 F1 62 71 0A 01 4C ?ñbq..L


JOB_STATUS = OKAY
ECU_ADR = 63
ECU_GROBNAME = MASK/CCC
ID_SG_ADR = 99 00 00 00 63 ...c
FLASH_PROGRAMMIER_STATUS_TEXT = Normalbetrieb
FLASH_PROGRAMMIER_STATUS = 1 00 01 ..
_TEL_ANTWORT = 7 Bytes
0000 : 83 F1 63 71 0A 01 4C ?ñcq..L

JOB_STATUS = OKAY
ECU_ADR = A0
ECU_GROBNAME = CCC
ID_SG_ADR = 160 00 00 00 A0 ... 
FLASH_PROGRAMMIER_STATUS_TEXT = Normalbetrieb
FLASH_PROGRAMMIER_STATUS = 1 00 01 ..
_TEL_ANTWORT = 7 Bytes
0000 : 83 F1 A0 71 0A 01 4C ?ñ q..L

The CIC should go here.

[russellg]

The CIC should go here.

Do you mean that the CiC should be working based on those results?

Is there anything I should have done after completing the last flash to boot it into life?

[hojo29]

The CIC should go here.

Do you mean that the CiC should be working based on those results?

Is there anything I should have done after completing the last flash to boot it into life?

According to the result of Tool32, CIC should go.

[russellg]

The CIC should go here.

Do you mean that the CiC should be working based on those results?

Is there anything I should have done after completing the last flash to boot it into life?

According to the result of Tool32, CIC should go.

Is there perhaps anything I need to do in NCSExpert before I default code the CHAMP ECU?

[hojo29]

Every navigation system runs after installation.
At the coding it is not at first.

VIRTSG9B OKAY 9248629
The control unit can also be programmed

[russellg]

Every navigation system runs after installation.
At the coding it is not at first.

VIRTSG9B OKAY 9248629
The control unit can also be programmed

I wonder if that’s where the problem lies. Those two virtual controllers have much older numbers and never take on the VIN.

I have started again, flashing 63.

However, do you know the procedure for flashing the VIRTSGB’s?

[russellg]

That' 63 flashed again with programming okay.

Almost took 24hrs to the minute.

Starting with 62 now. Fingers crossed....

[russellg]

Okay,

An update on progress after the last attempt:

Successfully flashed 63 and then 62 in comfort mode, update programming okay. A0 flash failed in comfort mode but I then managed to program it Expert Mode.

However, the CIC unit is the same, hasn’t booted up, fan spinning constantly.

I flashed it with CH63F1, CH62F1 in comfort mode the 11FLASH4.prg, 01010402cha0f1.ipo, and 9290230A.0pa in expert mode.

What am I doing wrong?

Should I be using the PKR files?
Should I be using Mensch Machine Interface MMI? I’ve been programming in comfort mode with Unverbaut

I’m not sure if it matters but the virtual controllers are still returning old program numbers and 0000000 chassis number.

92 VIRTSG92 OKAY 9233590 0000000 01.01.2008
9B VIRTSG9B OKAY 9248629 0000000 01.01.2008

I’d like to try Blax123’s suggesting of using ISTA/P, but I couldn’t set the i_stufe_schreiben to R056-10-03-501; R056-10-03-501; R056-10-03-501 - JOB_STATUS = ERROR_ARGUMENT

Does anyone have any ideas? Is there anything I should do after I see zUSB programming okay to boot it into life?

Thanks for your help so far guys.