[blax123]

Load again r56.prg and try i_stufe_schreiben with "R056-10-03-503;R056-10-03-503;R056-10-03-503" (without the quotes"") or with "R056-10-06-500;R056-10-06-500;R056-10-06-500".
It should work normally.

[russellg]

Thanks blax123,

Its worked! I realise now that I had an extra space after each semi-colon (. My mistake.

I have set apiJob("R56","i_stufe_lesen","R056-10-03-501;R056-10-03-501;R056-10-03-501","") as per your first note.

A I right in thinking I can use ISAT/P now? Bearing in mind I am trying to retrofit the Champ 2 CIC into the Pre-LCI R56?

Thanks again for your help, I click the thanks button too for your help to date.

[blax123]

Thanks blax123,

Its worked! I realise now that I had an extra space after each semi-colon (. My mistake.

I have set apiJob("R56","i_stufe_lesen","R056-10-03-501;R056-10-03-501;R056-10-03-501","") as per your first note.

A I right in thinking I can use ISAT/P now? Bearing in mind I am trying to retrofit the Champ 2 CIC into the Pre-LCI R56?

Thanks again for your help, I click the thanks button too for your help to date.

Open ISTA-D/ISTA+ and check now if it shows your CIC-Mid or still shows the CCC. If it shows the CIC-Mid you should be good to go with Ista-P.


Fingers crossed for you!

[russellg]

The car originally had a CCC, i'm going to try

R056-10-03-503;R056-10-03-503;R056-10-03-503

and will report back.

Same error. Cant progress in ISTA/P

The central gateway is clearly not operating correctly: All downline control units are not responding

Anyone have any ideas?

Thanks

---

Okay,

Latest progress update.

With the original intergration level I have the following error when I run ISTA/P, obviously because the CHAMP2 was not part of my factory FA.

Original:
R056-06-12-511;R056-10-03-501;R056-08-09-510

The following control units have been identified in the vehicle:
-GW
-CON
-CID
- CHAMP2-B
- CHAMP2-A
According to the vehicle order. however. these control units are not fitted.
Remove the control units or select the corresponding conversion

But when I change my interg. level to

R056-10-03-501;R056-10-03-501;R056-10-03-501

Then I have the following error and ISTA/P will not let me proceed becuase of a non functioning gateway.

The following control units have been identified in the vehicle:
- SZL
- JBE
- EPS
-CAS
- ABS/ASC/DSC
- KOMBI
-ACSM
-GW
-CON
-80
-FRM
-CID
- CHAMP2-H/RAD-H
- CHAMP2-B
- CHAMP2-A
- DME/DDE
According to the vehicle order, however, these control units are not fitted.

The car originally had a CCC, i'm going to try

R056-10-03-503;R056-10-03-503;R056-10-03-503

and will report back.

[hojo29]

62 MOSTGW OKAY 9290218 CH62F1
63 MASK/CCC OKAY 9290212 CH63F1
92 VIRTSG92 OKAY 9233590
9B VIRTSG9B OKAY 9248629 CH9BF1 New 9290231
A0 CCC OKAY 9290230 CHA0F1

[simaservis1108]

You flashed it for nothing.
Intel's patch only works with CIC and not CHAMP2.

Regards
Sima

[russellg]

62 MOSTGW OKAY 9290218 CH62F1
63 MASK/CCC OKAY 9290212 CH63F1
92 VIRTSG92 OKAY 9233590
9B VIRTSG9B OKAY 9248629 CH9BF1 New 9290231
A0 CCC OKAY 9290230 CHA0F1

Thanks hojo29, I wish I picked up on that when you mentioned it back in Post #17. I'm currently flashing 9B, is 92 able to be flashed too?

You flashed it for nothing.
Intel's patch only works with CIC and not CHAMP2.

Regards
Sima

Thanks Sima, I realise that now after blax123 advised that back in Post #6. Worth capturing it here again though in case any future users are thinking of flashing the Champ2 for INTEL123's method before reading SweetBMW's 'How to'.

[smercki]

Hello
I connect to this post
on the R60 of 2010 the Champ has been turned off after IstaP update failed
I updated the following controllers successfully with winkfp (CH63F1,
CH62F1, CHA0F1) but the monitor remains off, I forgot some module, the gateway for example?
I thank those who answer

[russellg]

Hello
I connect to this post
on the R60 of 2010 the Champ has been turned off after IstaP update failed
I updated the following controllers successfully with winkfp (CH63F1,
CH62F1, CHA0F1) but the monitor remains off, I forgot some module, the gateway for example?
I thank those who answer

Hello smercki,
Is your champ cooling fan spinning continuously?

Does you car beep when tbe key is inserted?

Does the radio work despite the CID monitor being blank?

Is your Champ factory supplied or retrofit?

[smercki]

Hello
I connect to this post
on the R60 of 2010 the Champ has been turned off after IstaP update failed
I updated the following controllers successfully with winkfp (CH63F1,
CH62F1, CHA0F1) but the monitor remains off, I forgot some module, the gateway for example?
I thank those who answer

Hello smercki,
Is your champ cooling fan spinning continuously?

Does you car beep when tbe key is inserted?

Does the radio work despite the CID monitor being blank?

Is your Champ factory supplied or retrofit?

thanks for the quick answer!
black monitor, no sound from the radio and no buttons work, the cooling fan runs continuously, factory present, no retrofit