Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
A difficult problem - Flash R56 Champ2 CiC with WinKFP - what is address 92 and 9B?
07-02-2018, 19:07 PM,
(This post was last modified: 07-02-2018, 19:07 PM by hojo29.)
Post: #11
|
|||
|
|||
RE: A difficult problem - Flash R56 Champ2 CiC with WinKFP - what is address 92 and 9B?
What status has the address 63,62 and A0 at Tool32?
|
|||
07-02-2018, 19:34 PM,
Post: #12
|
|||
|
|||
RE: A difficult problem - Flash R56 Champ2 CiC with WinKFP
(07-02-2018, 19:07 PM)hojo29 Wrote: What status has the address 63,62 and A0 at Tool32? Running apiJob("R56","flash_programmier_status_lesen_funktional","","") returns :- JOB_STATUS = OKAY ECU_ADR = 62 ECU_GROBNAME = MOSTGW ID_SG_ADR = 98 00 00 00 62 ...b FLASH_PROGRAMMIER_STATUS_TEXT = Normalbetrieb FLASH_PROGRAMMIER_STATUS = 1 00 01 .. _TEL_ANTWORT = 7 Bytes 0000 : 83 F1 62 71 0A 01 4C ?ñbq..L JOB_STATUS = OKAY ECU_ADR = 63 ECU_GROBNAME = MASK/CCC ID_SG_ADR = 99 00 00 00 63 ...c FLASH_PROGRAMMIER_STATUS_TEXT = Normalbetrieb FLASH_PROGRAMMIER_STATUS = 1 00 01 .. _TEL_ANTWORT = 7 Bytes 0000 : 83 F1 63 71 0A 01 4C ?ñcq..L JOB_STATUS = OKAY ECU_ADR = A0 ECU_GROBNAME = CCC ID_SG_ADR = 160 00 00 00 A0 ... FLASH_PROGRAMMIER_STATUS_TEXT = Normalbetrieb FLASH_PROGRAMMIER_STATUS = 1 00 01 .. _TEL_ANTWORT = 7 Bytes 0000 : 83 F1 A0 71 0A 01 4C ?ñ q..L |
|||
07-02-2018, 19:46 PM,
Post: #13
|
|||
|
|||
RE: A difficult problem - Flash R56 Champ2 CiC with WinKFP - what is address 92 and 9B?
(07-02-2018, 19:34 PM)russellg Wrote:(07-02-2018, 19:07 PM)hojo29 Wrote: What status has the address 63,62 and A0 at Tool32? The CIC should go here. |
|||
07-02-2018, 20:00 PM,
Post: #14
|
|||
|
|||
RE: A difficult problem - Flash R56 Champ2 CiC
|
|||
07-02-2018, 20:17 PM,
Post: #15
|
|||
|
|||
RE: A difficult problem - Flash R56 Champ2 CiC with WinKFP - what is address 92 and 9B?
(07-02-2018, 20:00 PM)russellg Wrote:(07-02-2018, 19:07 PM)hojo29 Wrote: The CIC should go here. According to the result of Tool32, CIC should go. |
|||
07-02-2018, 21:11 PM,
Post: #16
|
|||
|
|||
RE: A difficult problem - Flash R56 Champ2 CiC with WinKFP - what is address 92 and 9B?
(07-02-2018, 20:17 PM)hojo29 Wrote:(07-02-2018, 20:00 PM)russellg Wrote:(07-02-2018, 19:07 PM)hojo29 Wrote: The CIC should go here. Is there perhaps anything I need to do in NCSExpert before I default code the CHAMP ECU? |
|||
07-02-2018, 21:46 PM,
(This post was last modified: 07-02-2018, 22:08 PM by hojo29.)
Post: #17
|
|||
|
|||
RE: A difficult problem - Flash R56 Champ2 CiC with WinKFP - what is address 92 and 9B?
Every navigation system runs after installation.
At the coding it is not at first. VIRTSG9B OKAY 9248629 The control unit can also be programmed |
|||
07-02-2018, 22:51 PM,
Post: #18
|
|||
|
|||
RE: A difficult problem - with WinKFP - 92 and 9B?
(07-02-2018, 21:46 PM)hojo29 Wrote: Every navigation system runs after installation. I wonder if that’s where the problem lies. Those two virtual controllers have much older numbers and never take on the VIN. I have started again, flashing 63. However, do you know the procedure for flashing the VIRTSGB’s? |
|||
08-02-2018, 21:18 PM,
Post: #19
|
|||
|
|||
RE: A difficult problem - Flash R56 Champ2 CiC with WinKFP - what is address 92 and 9B?
That' 63 flashed again with programming okay.
Almost took 24hrs to the minute. Starting with 62 now. Fingers crossed.... |
|||
15-02-2018, 09:21 AM,
Post: #20
|
|||
|
|||
What am I doing wrong?
Okay,
An update on progress after the last attempt: Successfully flashed 63 and then 62 in comfort mode, update programming okay. A0 flash failed in comfort mode but I then managed to program it Expert Mode. However, the CIC unit is the same, hasn’t booted up, fan spinning constantly. I flashed it with CH63F1, CH62F1 in comfort mode the 11FLASH4.prg, 01010402cha0f1.ipo, and 9290230A.0pa in expert mode. What am I doing wrong? Should I be using the PKR files? Should I be using Mensch Machine Interface MMI? I’ve been programming in comfort mode with Unverbaut I’m not sure if it matters but the virtual controllers are still returning old program numbers and 0000000 chassis number. 92 VIRTSG92 OKAY 9233590 0000000 01.01.2008 9B VIRTSG9B OKAY 9248629 0000000 01.01.2008 I’d like to try Blax123’s suggesting of using ISTA/P, but I couldn’t set the i_stufe_schreiben to R056-10-03-501; R056-10-03-501; R056-10-03-501 - JOB_STATUS = ERROR_ARGUMENT Does anyone have any ideas? Is there anything I should do after I see zUSB programming okay to boot it into life? Thanks for your help so far guys. |
|||
« Next Oldest | Next Newest »
|
Possibly Related Threads… | |||||
Thread | Author | Replies | Views | Last Post | |
Winkfp cannot read uif | MPTeam | 7 | 222 |
27-04-2024, 19:07 PM Last Post: MPTeam |
|
Bmw G31 retrofit Mgu id7 atm problem | intranet | 20 | 2,487 |
26-04-2024, 08:06 AM Last Post: smilo |
|
Manual : How to Flash Any NBTevo ID4 to ID5 or ID6 ECE/US/ASIA | FSCmap | 184 | 53,666 |
24-04-2024, 14:49 PM Last Post: Bag3ban1 |
|
NBT EVO Connected Drive problem after update I-Level | SkeYT | 47 | 4,792 |
22-04-2024, 11:44 AM Last Post: kwat |
|
CHAMP2 Emulator Nav | BimmerLubuskie | 2 | 164 |
19-04-2024, 20:57 PM Last Post: miskoh |
|
Flash CAS 3 for disable ELV | UnFan | 3 | 234 |
19-04-2024, 08:20 AM Last Post: ravager |
|
Flash MPPK software 20D B47 (Esys) | ruben_17non | 5 | 602 |
10-04-2024, 21:38 PM Last Post: ruben_17non |
|
BMW E60 coding problem | GarageX | 8 | 377 |
02-04-2024, 10:07 AM Last Post: GarageX |
|
BMW G8x M3/M4 CSL EGS flash | weby | 22 | 3,708 |
31-03-2024, 19:48 PM Last Post: Erezbmwm |
|
m2 g87 csl flash | Erezbmwm | 0 | 143 |
31-03-2024, 18:46 PM Last Post: Erezbmwm |
Users browsing this thread:
2 Guest(s)
2 Guest(s)
Return to TopReturn to Content