Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
A4 B5 MCU Cluster transfer
07-02-2018, 09:25 AM,
Post: #1
|
|||
|
|||
A4 B5 MCU Cluster transfer
Hi,
can someone answer me if I can swap HC08 MCU if mask is the same? Both are A4 B5 clusters from Jaeger. |
|||
08-02-2018, 09:14 AM,
Post: #2
|
|||
|
|||
RE: A4 B5 MCU Cluster transfer
(07-02-2018, 09:25 AM)zix1 Wrote: Hi, Should be able to if mask is same as same chip If mine or others posts and info are helpful please give thanks/rep
|
|||
08-02-2018, 09:20 AM,
Post: #3
|
|||
|
|||
A4 B5 MCU Cluster transfer
(08-02-2018, 09:14 AM)dil6222 Wrote:(07-02-2018, 09:25 AM)zix1 Wrote: Hi, Is the bigger 912s chip also important for that or just the2j74y mcu? Must be part number of cluster the same? Can I also write only eeprom is flash version is different? |
|||
08-02-2018, 19:46 PM,
Post: #4
|
|||
|
|||
RE: A4 B5 MCU Cluster transfer
(08-02-2018, 09:20 AM)zix1 Wrote:(08-02-2018, 09:14 AM)dil6222 Wrote:(07-02-2018, 09:25 AM)zix1 Wrote: Hi, Not sure for this 1st question but If you can take 912s from original dash and swap it over it wouldn't hurt ideally yes needs to be same part number cluster for better chance of repair as without knowing and testing different dashes it hard to say what other clusters can be used its best to stick to matching part numbers to eliminate adding another possible problem. And for this last question all I can suggest is try just with eeprom and see if it works as I should think flash mainly runs needles etc but if you need flash I presume is the 1 you've been looking for but haven't found If mine or others posts and info are helpful please give thanks/rep
|
|||
08-02-2018, 20:03 PM,
(This post was last modified: 09-02-2018, 02:15 AM by 23Andi23.)
Post: #5
|
|||
|
|||
RE: A4 B5 MCU Cluster transfer
Software version is same? You have Stickers with V7.xx on MCU
must be same Version or 912 maybe not work with it. And if you swap 912 you need to adapt immo and keys because is stored in 912 |
|||
08-02-2018, 22:49 PM,
(This post was last modified: 09-02-2018, 02:15 AM by 23Andi23.)
Post: #6
|
|||
|
|||
RE: A4 B5 MCU Cluster transfer
(08-02-2018, 20:03 PM)23Andi23 Wrote: Software version is same? You have Stickers with V7.xx on MCU So he will need the 912 from original dash then and MCU must be same version If mine or others posts and info are helpful please give thanks/rep
|
|||
Reputation: +1 - zix1 [+1] | |||
09-02-2018, 02:10 AM,
(This post was last modified: 09-02-2018, 02:13 AM by 23Andi23.)
Post: #7
|
|||
|
|||
RE: A4 B5 MCU Cluster transfer
Why you want swap HC08? This you only touch if dash have problems. You want change Dash? Think only work if you swap both mcu´s there are too many different Software Versions for HC08 (V7.94ML, V7.94HL, V8.35ML, V8.42ML, V8.51ML, V8.55ML, V8.58ML, V8.40HL, V8.42HL, V8.51HL, V8.53HL, V8.55HL,
V8.58HL, V7.66ML, V7.66HL, V7.95ML, V7.95HL, V7.91ML, V7.92ML, V7.91HL, V7.92HL, V8.40HL, V7.47ML, V7.48ML, V7.49ML, V7.4cML, V7.64ML, V7.4DML, V7.65ML, V7.82ML, V7.47HL, V7.62HL, V7.48HL, V7.49HL, V7.4cHL, V7.64HL, V7.4dHL, V7.65HL, V7.82HL). Next is on this dashes there are 2 versions of gauges for fuel mounted. if Dash is not exactly the same needles maybe work wrong. Look on codecard site or search for Carprog 2j74y repair. " If everything is OK, just fuel gauge works in reverse – incorrect part (cluster) is installed in car. In Audi can be used 2 kind of fuel level meters – normal and reverse. Then fuel is empty one dash can show “0”, other “full”. This fault usually appears when you swapping instrument clusters. Is not possible to adapt fuel gauge type by ODB2, you must exchange instrument cluster." Easiest way is put new dash in car look if fuel gauge is ok -> find anyone with Orange5 Carprog or other programm which can read eeprom of hc912dg128 (just 4 wires needed to PCB) -> read eeprom of both dashes -> get login out from both -> make mileage in dump for new dash -> write new dump and adapt ecu and keys by diagnostic. And be carefully on mileage it is with CRC normaly and with wrong calc you get 999.999km If you upload both dumps we can help you on login and mileage |
|||
Reputation: +2 - zix1 [+1] , McMihai [+1] | |||
09-02-2018, 09:11 AM,
Post: #8
|
|||
|
|||
RE: A4 B5 MCU Cluster transfer
(09-02-2018, 02:10 AM)23Andi23 Wrote: Why you want swap HC08? This you only touch if dash have problems. You want change Dash? Think only work if you swap both mcu´s there are too many different Software Versions for HC08 (V7.94ML, V7.94HL, V8.35ML, V8.42ML, V8.51ML, V8.55ML, V8.58ML, V8.40HL, V8.42HL, V8.51HL, V8.53HL, V8.55HL, hes gonna have problems then 23andi as doesent have flash from original dash was searching for a dump with same software version but haven't found it yet If mine or others posts and info are helpful please give thanks/rep
|
|||
Reputation: +1 - zix1 [+1] | |||
09-02-2018, 16:56 PM,
Post: #9
|
|||
|
|||
RE: A4 B5 MCU Cluster transfer
Thanks mates!
Things changed. I have a carprog now. So i am able to write read/write flash without having flash dump =) how can i read 912 with carprog? |
|||
10-02-2018, 17:25 PM,
Post: #10
|
|||
|
|||
RE: A4 B5 MCU Cluster transfer
Read carprog PDF for 912
|
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
2 Guest(s)
2 Guest(s)
Return to TopReturn to Content