Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

[Question] How to use newest ISTA-P without IBAC Codes for F-Series for flashing
18-03-2018, 08:00 AM, (This post was last modified: 18-03-2018, 08:04 AM by M-Simon.)
Post: #1
[Question] How to use newest ISTA-P without IBAC Codes for F-Series for flashing
Hi,

ISTA-P Support for newer models (like F, G and I Series) was discontiniued (last version with full support was 3.63.4).

But I heard / and read that newer ISTA-P versions can be still used with IBAC-Code for the affected models.

What does that means excatly? There are a lot of tools for generating IBAC-Codes (like ISTA-P Launcher from Beemerboy88) but this codes are only for retrofiting as far as I see.

How can I flash the entire car with ISTA-P and IBAC Code / which IBAC Code have to use?

I think this is important for users with retrofitted ECUS which should not be flashed in ISTA-P in expert mode.

Thank you very much!


Attached Files Thumbnail(s)
   
Quote this message in a reply
[+] 2 users say Thank You to M-Simon for this post
18-03-2018, 08:29 AM, (This post was last modified: 18-03-2018, 09:47 AM by Bimmer540.)
Post: #2
RE: [Question] How to use newest ISTA-P without IBAC Codes for F-Series for flashing
From which version of Ista-p is IBAC Code requested?
Quote this message in a reply
[+] 2 users say Thank You to Bimmer540 for this post
18-03-2018, 08:36 AM,
Post: #3
RE: [Question] How to use newest ISTA-P without IBAC Codes for F-Series for flashing
ISTA-P will give you the order code, for example 001D.
Then generate the IBAC.
Quote this message in a reply
[+] 2 users say Thank You to beemered for this post
18-03-2018, 09:33 AM,
Post: #4
RE: [Question] How to use newest ISTA-P without IBAC Codes for F-Series for flashing
The session can be continued with the IBAC code, retrofitting is no longer available.


Attached Files Thumbnail(s)
   
Quote this message in a reply
[+] 4 users say Thank You to Jumper for this post
18-03-2018, 11:42 AM,
Post: #5
RE: [Question] How to use newest ISTA-P without IBAC Codes for F-Series for flashing
@myfirst1er How do you decide / know which key number (5 in your case) is needed?

Thanks again!
Quote this message in a reply
18-03-2018, 14:35 PM, (This post was last modified: 18-03-2018, 18:47 PM by Jumper.)
Post: #6
RE: [Question] How to use newest ISTA-P without IBAC Codes for F-Series for flashing
(18-03-2018, 11:42 AM)Munich Simon Wrote:  @myfirst1er How do you decide / know which key number (5 in your case) is needed?

Thanks again!

Today I generated the IBAC with key 1 and the retrofits appear
Quote this message in a reply
[+] 2 users say Thank You to Jumper for this post
19-03-2018, 08:23 AM,
Post: #7
RE: [Question] How to use newest ISTA-P without IBAC Codes for F-Series for flashing
(18-03-2018, 08:00 AM)Munich Simon Wrote:  Hi,

ISTA-P Support for newer models (like F, G and I Series) was discontiniued (last version with full support was 3.63.4).

But I heard / and read that newer ISTA-P versions can be still used with IBAC-Code for the affected models.

What does that means excatly? There are a lot of tools for generating IBAC-Codes (like ISTA-P Launcher from Beemerboy88) but this codes are only for retrofiting as far as I see.

How can I flash the entire car with ISTA-P and IBAC Code / which IBAC Code have to use?

I think this is important for users with retrofitted ECUS which should not be flashed in ISTA-P in expert mode.

Thank you very much!

Two solutions.one is IBAC generator then whole car programming will go on.the other is ISTA with all programming data was installed before.
Quote this message in a reply
19-03-2018, 09:49 AM,
Post: #8
RE: [Question] How to use newest ISTA-P without IBAC Codes for F-Series for flashing
Guys, who can explain it to me, what is the ISTA/P for? I always use E-Sys and just want to understand the importance of ISATA/P
Quote this message in a reply
25-01-2019, 08:32 AM,
Post: #9
RE: [Question] How to use newest ISTA-P without IBAC Codes for F-Series for flashing
I understand how to generate the IBAC code to enable ISTA-P, but the latest standalone versions do not contain PSDZ. Can I simply inject the PSDZ from the same version into the ISTA-P/BMW/Services/data/ecudata folder to enable ISTA-P for F-series?
Quote this message in a reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  ista for use whit vcx se db8000 0 7 10 minutes ago
Last Post: db8000
  ista 4.46 Standalone kiranabc 31 2,788 31 minutes ago
Last Post: kiranabc
  Disable CC messages relating to a CC-ID codes TheNine90 102 13,304 4 hours ago
Last Post: Wibbles
  AOS Ista possible to deactivate second check after scan? RaoulK1998 17 277 4 hours ago
Last Post: RaoulK1998
XZBMW ISTA 4.46.xx problems and possible solution Sedoy 76 7,256 Yesterday, 20:02 PM
Last Post: Node
XZBMW ISTA Standalone Licenserequest up to v4.37.4x Sedoy 8,646 627,263 Yesterday, 16:29 PM
Last Post: Sedoy
XZBMW Update ISTA at once 4.43.40 (ISTA Update Program) charlesjyw 34 6,412 Yesterday, 10:39 AM
Last Post: MINIGP1610
XZBMW BMW ISTA-P Rheingold 69.0.200 (Torrent File) carsoftcare 1 119 26-03-2024, 12:09 PM
Last Post: hlip
  ISTA launcher problem Red_bean_bun 1 155 26-03-2024, 05:11 AM
Last Post: 2013m5
XZBMW Adding a new vehicle/model to "Reingold" ISTA+ dieselweasel 12 660 25-03-2024, 08:11 AM
Last Post: Node

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content