Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Install Cruise and Speed Limiter Citroen C Elysee
12-07-2018, 01:22 AM,
Post: #1
|
|||
|
|||
Install Cruise and Speed Limiter Citroen C Elysee
Hello guys. I had connection problems with my lexia before and it was because its not full chip so i bought a full chip and it works great.
Now i am trying to fit a cruise control. I could enable it on the BSI but i cannot do it in the engine ecu. I go to Repair, Configuration of parameters, (it popup a few times the login window, but i click cancel and then it show me the parameters) then i change to Present both Cruise and Speed. But when i click the nut icon, it ask again the login a couple times, of course i cannot do anything else than cancel it and then it show a "programming error 414". I have tried many diagbox versions, after 7.40 the configuration is disabled. Also i tried through the Delivery vehicle to customer option but it also dont allow. I get a message something like "it cannot be installed on this vehicle". Its a valeo v46 ecu. You guys know how i can enable it? I was thinking in enable it connecting to the eeprom. (i did this once to twin a v46 ecu to the bsi). But i dont know which part of the dump should i modify. Thanks in advance Actually after i enabled it in the BSI the cruise control buttons works with the dashboard. But when i set the car in cruise or speed it dont work. Probably because its disabled in the engine ecu. |
|||
12-07-2018, 08:13 AM,
Post: #2
|
|||
|
|||
RE: Install Cruise and Speed Limiter Citroen C Elysee
Hi Mate, try with older version of Diagbox i.e : ver 7.34
|
|||
20-07-2018, 21:57 PM,
Post: #3
|
|||
|
|||
RE: Install Cruise and Speed Limiter Citroen C Elysee
I tried with 7.24 and same result :/ this Valeo v46.11 Is not good to deal
|
|||
21-07-2018, 14:07 PM,
Post: #4
|
|||
|
|||
RE: Install Cruise and Speed Limiter Citroen C Elysee
I have choosed V46.21 and it want to program. But at the end it give error as it's not a 46.21. Only v46 have this issue T_T
|
|||
22-07-2018, 00:02 AM,
Post: #5
|
|||
|
|||
RE: Install Cruise and Speed Limiter Citroen C Elysee
Hello guys. I know a little of programming. So i have doing some tests to find the script that is being executed when i try to do manual configuration to this injection valeo v46 ecu. I used notepad++ to search the string "46" and "46.21" in the AWRoot folder. Te result was the folder
Quote:C:\AWRoot\dtrd\tree\Vehicle\. This folder have subfolders for each car, and the string was found in like 3 folders. So i did some kind of discard. I renamed or deleted the each folder. And when my car folder was deleted an error is shown when you try to access CONFIGURATION in lexia. Finally i could identify the folder which diagbox uses when accesing my car configuration: Quote:C:\AWRoot\dtrd\tree\Vehicle\M3_M4\INJ\V46 The folder looks like the attachment photo i added. Then doing rename discard again. I found the files that are being executed when clicking "MANUAL CONFIGURATION" in diagbox are: Quote:M3_M4_V46_telecodage_manuel.s Now i will compare with that two files into C:\AWRoot\dtrd\tree\Vehicle\M3_M4\INJ\V46_21 folder which it allow car ecu configuration and try to find what is not allowing to do it. Does someone know something about this? |
|||
22-07-2018, 04:23 AM,
Post: #6
|
|||
|
|||
RE: Install Cruise and Speed Limiter Citroen C Elysee
I have done some research. At the moment i click the gear icon to program this files or part of them are called in the following order.
Quote:M3_M4_V46_TELECODAGE.s I have tried to replace some data of M3_M4_V46_TELECODAGE.s from the same file but located in V46.21 which actually allow ECU configuration. Once i did that, when you click the gear icon it dont ask for user and password 3 times, it go to ecu configuration directly but still show the message "programming error" but no like before. "programming error. error 414" which is probably because no user and pass entered. Anway i think the solution is not in this file, i think it is in the last 2 files. Which are used probably by many models of ecu. Which have this same issue. I think fixing it for my ecu will do the job for probably many others! |
|||
22-09-2018, 17:04 PM,
Post: #7
|
|||
|
|||
RE: Install Cruise and Speed Limiter Citroen C Elysee
Hi there,
Did you solve the problem? I'm trying to activate CC in my 206 with Sagem S2000 and having same problem as you. |
|||
22-10-2018, 12:23 PM,
(This post was last modified: 22-10-2018, 12:25 PM by scarymistake.)
Post: #8
|
|||
|
|||
RE: Install Cruise and Speed Limiter Citroen C Elysee
(22-07-2018, 04:23 AM)febianuy Wrote: I have done some research. At the moment i click the gear icon to program this files or part of them are called in the following order. Not from me and from another forum Here's a little how-to for telecoding with newer models. It solve the server connection problem. Go to folder C:/AwRoot/dtrd/tree/ there are three folders TeleXX TeleXX_PR TeleXX_TPM in each folder there's a file called script_atm_telexx.s It works with 7.57 but not with 7.83. Maybe someone can fix this code a little bit more. undefined It's not my code but i want to share it. Maybe someone can modify it a little bit more to work with 7.83. It's from peugeottalk.de from a user named 1uck3r. Open each file with an editor and replace all with this code: |