Advanced Search
Hello There, Guest! Login — Register
Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

Retrofit RearViewCAM issue on FEM
03-08-2018, 15:29 PM, (This post was last modified: 03-08-2018, 15:31 PM by mdma666.)
Post: #1
mdma666 Offline
Member
Members 		Posts: 35
Threads: 17
Threads: 17
Thanks Received: 3 in 3 posts
Thanks Given: 9
Joined: Nov 2015
Reputation: 1
XZBMW  Retrofit RearViewCAM issue on FEM
I installed and coded TRSVC on 2015 F82.
The TRSVC wont start up, no communication. Tested other TRSVC - the same. Check wiring and coding - all ok!

It seems like the FEM wont activate the K-Can.
I have a FEM ZB7 High but normally all FEMs are equipped with the K-Can Controller and it activates itself via coding any K-Can Client (TRSVC, RDC..)

to make sure:
- no wiring prob (CON 8 Pin51/52, 12v, Ground...)
- no coding prob (3AG via FA coded in ALL ECUs)
- checked K-Can wires with oszi; def. dead!
- fault memory is empty instead of REM "missing qualifier RearCam"
- I retrofitted the TRSVC about 50 times but never had a prob like that sad

dontknow


Any1 an idea how to activate the K-Can maybe with Tool32?!?!?
Quote this message in a reply
03-08-2018, 16:24 PM, (This post was last modified: 03-08-2018, 16:33 PM by nesa.)
Post: #2
nesa Offline
Member
Members 		Posts: 72
Threads: 9
Threads: 9
Thanks Received: 60 in 26 posts
Thanks Given: 38
Joined: Feb 2014
Reputation: 23
RE: Retrofit RearViewCAM issue on FEM
hi
Do you use Icam end did you connected to CAN3?
Quote this message in a reply
03-08-2018, 18:29 PM,
Post: #3
BimmerSLO Offline
Donator
******
Donators 		Posts: 192
Threads: 74
Threads: 74
Thanks Received: 65 in 25 posts
Thanks Given: 65
Joined: Apr 2017
Reputation: 12
RE: Retrofit RearViewCAM issue on FEM
Put a 120 Ohm resistor between Can high and Can low. That will activate can line.
Coding E + F Modelles in near from Graz, Austria
Navigation map updates
I-Step update
CIC, NBT, NBT EVO Retrofit and remote coding
Quote this message in a reply
[+] 2 users say Thank You to BimmerSLO for this post
03-08-2018, 20:44 PM, (This post was last modified: 03-08-2018, 20:46 PM by mdma666.)
Post: #4
mdma666 Offline
Member
Members 		Posts: 35
Threads: 17
Threads: 17
Thanks Received: 3 in 3 posts
Thanks Given: 9
Joined: Nov 2015
Reputation: 1
RE: Retrofit RearViewCAM issue on FEM
(03-08-2018, 16:24 PM)nesa Wrote:  hi
Do you use Icam end did you connected to CAN3?

TRSVC is not ICam
(03-08-2018, 18:29 PM)BimmerSLO Wrote:  Put a 120 Ohm resistor between Can high and Can low. That will activate can line.

normaly the 120Ohm are inside the TRSVC. I also tried the 120OHm between High-Low yesterday but Nothing changed. Its possible that you have one TRSVC without the resistor but not three.
I tried three different TRSVC Ecus
Quote this message in a reply
04-08-2018, 11:53 AM, (This post was last modified: 04-08-2018, 15:21 PM by BugFix.)
Post: #5
BugFix Offline
Member
Members 		Posts: 366
Threads: 7
Threads: 7
Thanks Received: 349 in 150 posts
Thanks Given: 11
Joined: Oct 2017
Reputation: 104
RE: Retrofit RearViewCAM issue on FEM
check the wirring diagram
one a question ...

did you install exactly the trsvc or icam ?


Attached Files
F30_RVC.pdf
File Type: .pdf
Downloaded: 45 times
Size: 513.75 KB

NBTEVO, ENAV2, MGU  - CP OFF, Navi , APPS , Carplay, AA
MGU ID-8-9-10 Cars - Full Region change
NCD Secure Coding 2.0




Quote this message in a reply
02-09-2018, 22:23 PM,
Post: #6
Mwahab Online
Donator
******
Donators 		Posts: 731
Threads: 72
Threads: 72
Thanks Received: 309 in 188 posts
Thanks Given: 329
Joined: Dec 2016
Reputation: 136
RE: Retrofit RearViewCAM issue on FEM
Sometimes this happens, just read errors, if it happen to be in transport mode u can easily delete it, if u didn't get any pinpoint error just give the car a good battery sleep and it work.
Sometimes after coding and everything it shows a black screen, happens to me alot. Cheers!
All my knowledge is free for exchange with valuable information
Sharing->Development
The Garage - Egypt
  • FSC Repair kits - FSC Retrofits and Conversions Service history
  • Secure Coding 2.0 Type Key, FA, SFA
  • NBT/EVO/EntryNav2/MGU
  • MGU Carplay/Android auto W/O Telematics/CP/Patching in Middle East and Northern Africa
  • Feature Installer codes B2B
  • DME VIN ISN Working Hours IMMO OFF File and Remote Service/SWIFTEC - MG1 MD1 IMMO OFF
  • (E,F,G) 7DCT - DKG - 8HP - 6HP - EGS7 ISN Reset
  • KAFAS4 Virgin and Patching Remote
  • CAS2/3/4 Full IMMO & LOCKSMITH Customization Dump & Remote
  • HUF5663_434Mhz NO REMOTE SIGNAL FIX
  • F&G Series Headlight Customization
Visit this user's website
Quote this message in a reply
03-09-2018, 06:24 AM,
Post: #7
CEBEP Offline
Member
Members 		Posts: 204
Threads: 26
Threads: 26
Thanks Received: 409 in 75 posts
Thanks Given: 374
Joined: Aug 2015
Reputation: 125
RE: Retrofit RearViewCAM issue on FEM
(03-08-2018, 15:29 PM)mdma666 Wrote:  I installed and coded TRSVC on 2015 F82.
The TRSVC wont start up, no communication. Tested other TRSVC - the same. Check wiring and coding - all ok!

It seems like the FEM wont activate the K-Can.
I have a FEM ZB7 High but normally all FEMs are equipped with the K-Can Controller and it activates itself via coding any K-Can Client (TRSVC, RDC..)

to make sure:
- no wiring prob (CON 8 Pin51/52, 12v, Ground...)
- no coding prob (3AG via FA coded in ALL ECUs)
- checked K-Can wires with oszi; def. dead!
- fault memory is empty instead of REM "missing qualifier RearCam"
- I retrofitted the TRSVC about 50 times but never had a prob like that sad

dontknow


Any1 an idea how to activate the K-Can maybe with Tool32?!?!?

calculate TAL with 3AG option - if it need FEM replacement - it will tell you
BMW tuning & retrofitting, https://www.instagram.com/cebepspb/
* lifetime EVO, ROUTE codes, Carplay, ECU Remap and other crap
Quote this message in a reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  G82 rear tail lights CSL retrofit Sauron 7 602 Yesterday, 12:26 PM
Last Post: SANYA
  Kafas issue aftrer ACC Retrofit It3_Magic 12 317 17-04-2024, 15:07 PM
Last Post: user_530d
XZBMW Neck warmer retrofit Just2fast5 5 330 17-04-2024, 11:20 AM
Last Post: Spirit5676
  TMS FRM3 F10 Coding issue mj_mj_mj 17 1,893 16-04-2024, 09:30 AM
Last Post: user_530d
  ID4 evo to ID6 Evo full retrofit, ATM issues 03178A mitch32 1 140 15-04-2024, 17:52 PM
Last Post: mitch32
  Bmw G31 retrofit Mgu id7 atm problem intranet 19 2,258 15-04-2024, 09:21 AM
Last Post: evaldazj
XZBMW BMW E84 Cruise control retrofit not workig Alyn546 4 205 12-04-2024, 14:23 PM
Last Post: DieStream
  F10 FLA retrofit beng2k 30 994 11-04-2024, 18:43 PM
Last Post: beng2k
XZBMW BMW f20 KOMBI2 retrofit bm92 15 453 10-04-2024, 07:51 AM
Last Post: bm92
XZBMW BMW G32 6 GT - Central Lock Issue DaBotta 3 182 06-04-2024, 07:44 AM
Last Post: Volum

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content