[gaznasty]

Hello CarTechnology,

Please could I ask if someone help me to viriginise another BSI from a Peugeot 307 2002, I have read and downloaded the eeprom bin file using Upa-usb device from HC912DG128.
Valeo BSI G0X-00

9636760580 F
9644098380
A11998 Boot : 7.2

I have retrieved my key for programming but please would someone help me to virginise the EEprom or an I supposed to read the entire flash memory?

When I tried this earlier I apparently had 1036 errors reading entire flash but no errors reading just the eeprom.

Bin is hopefully attached if anyone would please hep me to virginise as I dont know what or where to set the relevant data to FF.

Thank you in advance Garry

[volavka]

VIN: VF33C8HZB82478245
PIN: W8E9

Try this this bin ...
First coding bsi using Pin code then Program keys
The job done by PP2000

Good luck

[gaznasty]

Thank you for file.

Please could I ask what profile I'm supposed to use in Diagbox, as I'm on V5.20 and profile 2FFFFFF but there was no option anywhere to learn high frequency keys.

I Programmed 1 key and chip to car which did start but still no windscreen wipers. Checked comms 2000 which did show if switches were working. I did hear the relay click in the engine gsm but wipers are still no go.

I am left with "Automatic headlight fault", "Automatic Gearbox Fault", but I don't have either on my car and did switch them off after inputting details in the virgin his but still errors appear on monochrome display when starting.

I am suspecting my Delphi BSM B2 so an trying to work out if the Siemens BSM B2 would be a direct working replacement.

Any help would be appreciated

[ROD-BENDERS]

Thank you for file.

Please could I ask what profile I'm supposed to use in Diagbox, as I'm on V5.20 and profile 2FFFFFF but there was no option anywhere to learn high frequency keys.

I Programmed 1 key and chip to car which did start but still no windscreen wipers. Checked comms 2000 which did show if switches were working. I did hear the relay click in the engine gsm but wipers are still no go.

I am left with "Automatic headlight fault", "Automatic Gearbox Fault", but I don't have either on my car and did switch them off after inputting details in the virgin his but still errors appear on monochrome display when starting.

I am suspecting my Delphi BSM B2 so an trying to work out if the Siemens BSM B2 would be a direct working replacement.

Any help would be appreciated

I have seen this problem before... check wiper switch and or wiper motor

[volavka]

if you hear the realy click thats mean is no bsi problem
well check bcm in hood or maybe ground wire (green/wellow) in wiper motor

Good luck

[gaznasty]

if you hear the realy click thats mean is no bsi problem
well check bcm in hood or maybe ground wire (green/wellow) in wiper motor

Good luck

Thank you, will any BSM B2 from Peugeot or Citroen fit? Mine is 9646405180?

[volavka]

Thank you, will any BSM B2 from Peugeot or Citroen fit? Mine is 9646405180?

No matter the part number ,
Find any bcm for Peugeot 307 -2002

[gaznasty]

Thank you, will any BSM B2 from Peugeot or Citroen fit? Mine is 9646405180?

No matter the part number ,
Find any bcm for Peugeot 307 -2002

Thank you my friend, much appreciated!

[gaznasty]

okay replacement bsm b2 brought life back to wipers for all of 3 goes before all I could hear was motor slowing down so going for another wiper motor soon.

Please can I ask how I put reinstate my immobiliser back to on into my eeprom as above?

Would really appreciate your help as Diagbox seems to be stuck in a loop trying to learn keys before telling me to switch ignition off and remove key, then reinsert key and switch ignition on and telling me to wait 15 minutes and try again.

Please could someone help me to switch the Immobilier back on into eeprom bin/dump above please?

[gaznasty]

SOLVED!!!!!! wiper motor dispite working off car was dud, replaced wiper car wipers now running again. Thank you to contributors. New topic may appear