Please make sure you read Rules! and DO NOT upload/post any illegal softwares or Pirated Material , Thank you for understanding :)
  1. AutoHex II



Read/Write 512kb on Ms42
11-10-2018, 16:49 PM,
Post: #11
RE: Read/Write 512kb on Ms42
(11-10-2018, 16:33 PM)Enabled Wrote:  I have used windows 7 and windows 8.1, there shouldn't be a problem with Windows 10. You can attempt win7 compatibility, and as admin.

Okey! I have tried with the compatibility mode as admin but its the same. 
Do you know if kess v2 or any other software has the ability to read/write full flash on ms42?
Quote this message in a reply
11-10-2018, 17:38 PM, (This post was last modified: 11-10-2018, 17:51 PM by Enabled.)
Post: #12
RE: Read/Write 512kb on Ms42
Kess probably not.
Most other programs crash when trying to write to the boot sector.


Send me a PM with your email or some kind of communication, teamviewer, etc.
I have an alternative method to help for immediate purposes.
Quote this message in a reply
11-10-2018, 18:00 PM,
Post: #13
RE: Read/Write 512kb on Ms42
try "siemens flash tool" as far as I remember it can read out full flash trough OBD
Quote this message in a reply
16-10-2018, 17:28 PM, (This post was last modified: 16-10-2018, 17:28 PM by Sorken.)
Post: #14
RE: Read/Write 512kb on Ms42
Thanks everyone for helping! biggrin  Today I received my new cable and now it finally connected! (VAG-COM KKL 409.1)
However, it only connect using this method:

1. Connect everything - OBD, ECU and boot pin, but only to (-) Battery.
2. Plugin OBD usb to computer
3. Open Jmgarage
4. Connect cable to (+) on battery and hit connect immediately!

I got Jmgarage to write a virginized file successfully but INPA cant synchronize with EWS, I only get "NO RESPONSE FROM CONTROL UNIT" then I get error code 209 "Manipulation protection EWS". Do you guys have any advice on how to get them synchronized?
Quote this message in a reply
16-10-2018, 22:58 PM,
Post: #15
RE: Read/Write 512kb on Ms42
(16-10-2018, 17:28 PM)Sorken Wrote:  Thanks everyone for helping! biggrin  Today I received my new cable and now it finally connected! (VAG-COM KKL 409.1)
However, it only connect using this method:

1. Connect everything - OBD, ECU and boot pin, but only to (-) Battery.
2. Plugin OBD usb to computer
3. Open Jmgarage
4. Connect cable to (+) on battery and hit connect immediately!

I got Jmgarage to write a virginized file successfully but INPA cant synchronize with EWS, I only get "NO RESPONSE FROM CONTROL UNIT" then I get error code 209 "Manipulation protection EWS". Do you guys have any advice on how to get them synchronized?

set latency timer of COM port to 1 or 16ms then try again

Press [Image: postbit_reputation.gif] and[Image: Qi7qHzl.jpg], If this post helped you.thankyou
Quote this message in a reply
17-10-2018, 17:01 PM,
Post: #16
RE: Read/Write 512kb on Ms42
(16-10-2018, 22:58 PM)AutoExe3219 Wrote:  
(16-10-2018, 17:28 PM)Sorken Wrote:  Thanks everyone for helping! biggrin  Today I received my new cable and now it finally connected! (VAG-COM KKL 409.1)
However, it only connect using this method:

1. Connect everything - OBD, ECU and boot pin, but only to (-) Battery.
2. Plugin OBD usb to computer
3. Open Jmgarage
4. Connect cable to (+) on battery and hit connect immediately!

I got Jmgarage to write a virginized file successfully but INPA cant synchronize with EWS, I only get "NO RESPONSE FROM CONTROL UNIT" then I get error code 209 "Manipulation protection EWS". Do you guys have any advice on how to get them synchronized?

set latency timer of COM port to 1 or 16ms then try again

I have tried that with no success. Is INPA capable of doing a synchronize with a virginized ECU, or am I forced to use antoher software like GT1?
Quote this message in a reply
17-10-2018, 19:21 PM, (This post was last modified: 17-10-2018, 19:36 PM by Enabled.)
Post: #17
RE: Read/Write 512kb on Ms42
If you have it, use ISTA.

Did you do the virginize correctly?

I have done so many of these... I will look for the tool32 command sequence, but INPA should have worked.

In INPA you should be using the F1 button (first button), to transfer the start value from EWS to DME.
Quote this message in a reply
Yesterday, 15:35 PM,
Post: #18
RE: Read/Write 512kb on Ms42
(17-10-2018, 19:21 PM)Enabled Wrote:  If you have it, use ISTA.

Did you do the virginize correctly?

I have done so many of these... I will look for the tool32 command sequence, but INPA should have worked.

In INPA you should be using the F1 button (first button), to transfer the start value from EWS to DME.

I dont have ISTA, but at the moment I am trying to install dis.v44. 

I believe so, the file has been used by many and the writing went okay. I checked the ISN and it was cleared with FF. Is there something else I should check?

I get error from pressing F1 and F2.
Quote this message in a reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  CiC Read code 1B with USB MaxBmw 59 16,855 06-10-2018, 07:46 AM
Last Post: Sedoy
  QNX EVO : How to Mount Data as Read/Write from Read Only? bmwcoder75 3 209 05-10-2018, 08:03 AM
Last Post: psya
XZBMW VTI read value fault rheingold ista-d!!!F10 525xd atc-350 nack76 0 112 08-09-2018, 08:33 AM
Last Post: nack76
XZBMW [solved] BMW E9X M3 MSS60 original full read beemered 6 792 20-08-2018, 12:14 PM
Last Post: Enabled
  Combox E9x faulty flash. Want to write dump Fx82 8 342 09-08-2018, 04:51 AM
Last Post: Fx82
XZBMW BMW F10 M5 DME Master and Slave boot read needs nesa 0 153 19-07-2018, 19:54 PM
Last Post: nesa
  Ncsexpert read fine VIN but no getcode ? ka_rai 5 248 29-06-2018, 06:02 AM
Last Post: willisodhiambo
  [Solved!] E46 read UIF with INPA snypertje 2 328 14-06-2018, 18:45 PM
Last Post: hojo29
  Read / write ISN in EGS module ocostel 10 1,586 23-04-2018, 14:22 PM
Last Post: 16eddi67
  X1 2018 - can`t read in esys only HU_ENTRYNAV2 rest of all I can snf11lci 11 1,322 17-04-2018, 15:20 PM
Last Post: larrybml

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content