Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

cas / cluster bench setup
15-10-2018, 17:43 PM,
Post: #11
RE: cas / cluster bench setup
here is power supply im using
thank you everyone for the help. tonight ill draw out how i have everything connected, maybe someone can see if i have something wrong.

[Image: 25nqSYZ.jpg]
Quote this message in a reply
16-10-2018, 03:40 AM,
Post: #12
RE: cas / cluster bench setup
heres what i have

Obd2
1: Wake
4: Ground
5: Ground
6: to cas 34 CAN H
14: to cas 17 CAN L

JBBE
Blue plug
46: to cas 35 CAN H
26: to cas 26 CAN L

47 pin plug
23: Ground

23 pin plug
21: +12v

Black plug
29: to kombi 6 pin CAN H
31: to kombi 7 pin CAN L

CAS
21: +12v
34: +12v
25: Ground
11: Ground
34: to 6 obd CAN H
17: to 14 obd CAN L
19: wake
ribbon to key holder and start button

KOMBI
9: +12v
18: Ground
6: to jbbe 29 CAN H
7: to jbbe 31 CAN L
Quote this message in a reply
16-10-2018, 09:02 AM,
Post: #13
RE: cas / cluster bench setup
(14-10-2018, 10:08 AM)wxwwxw Wrote:  You need minimum:
CAS + key socket + button
JBBE (in jbbe there are 3 CAN buses, one for obd2, the other for DDE, DSC, EPS, EKP. Third to CAS, KOMBI, CID, ZBE, KLIMA, MRS, FRM, PDC, FZD ...)
If CAS from Europe is still ELV
I also did something trash in a more extended version:
https://www.youtube.com/watch?v=LnVHZ0ImeZA

is it possible to code with this setup? best regards.
Quote this message in a reply
16-10-2018, 18:29 PM,
Post: #14
RE: cas / cluster bench setup
(16-10-2018, 09:02 AM)dommeij Wrote:  
(14-10-2018, 10:08 AM)wxwwxw Wrote:  You need minimum:
CAS + key socket + button
JBBE (in jbbe there are 3 CAN buses, one for obd2, the other for DDE, DSC, EPS, EKP. Third to CAS, KOMBI, CID, ZBE, KLIMA, MRS, FRM, PDC, FZD ...)
If CAS from Europe is still ELV
I also did something trash in a more extended version:
https://www.youtube.com/watch?v=LnVHZ0ImeZA

is it possible to code with this setup? best regards.

Yes, that's enough

Here is my more extensive version

https://youtu.be/FdAD2EnC3gk
Quote this message in a reply
16-10-2018, 19:30 PM,
Post: #15
RE: cas / cluster bench setup
10A should be enough for the bench except CIC (it can consume more than 10A) or NBT.

Also it's better to have CAS3 non-ELV version (or flash to it) instead of CAS2.
Quote this message in a reply
17-10-2018, 02:48 AM,
Post: #16
RE: cas / cluster bench setup
can anyone verify if the pinout i posted above are correct? tried my best to do it from the diagrams posted, but im not the best at reading diagrams and still learning.
Quote this message in a reply
17-10-2018, 15:01 PM,
Post: #17
RE: cas / cluster bench setup
(16-10-2018, 03:40 AM)Cniksor Wrote:  heres what i have

Obd2
1: Wake
4: Ground
5: Ground
6: to cas 34 CAN H
14: to cas 17 CAN L

JBBE
Blue plug
46: to cas 35 CAN H
26: to cas 26 CAN L

47 pin plug
23: Ground

23 pin plug
21: +12v

Black plug
29: to kombi 6 pin CAN H
31: to kombi 7 pin CAN L

CAS
21: +12v
34: +12v
25: Ground
11: Ground
34: to 6 obd CAN H
17: to 14 obd CAN L
19: wake
ribbon to key holder and start button

KOMBI
9: +12v
18: Ground
6: to jbbe 29 CAN H
7: to jbbe 31 CAN L

Check the JBBE power supply


Attached Files Thumbnail(s)
   
Quote this message in a reply
18-10-2018, 17:01 PM, (This post was last modified: 18-10-2018, 17:04 PM by wxwwxw.)
Post: #18
RE: cas / cluster bench setup
(17-10-2018, 02:48 AM)Cniksor Wrote:  can anyone verify if the pinout i posted above are correct? tried my best to do it from the diagrams posted, but im not the best at reading diagrams and still learning.




It will start by connecting the JBBE itself. If you connect as below, up to 65s after turning on the power you will be able to connect through obd2.

blue connector JBBE
33 - 14 obd2
17 - 6 obd2

47 pin connector

23 - GND

23 pin connector

3 + 12v
5 + 12v
6 + 12v
7 + 12v
21 + 12v
22 + 12v
23 + 12v


obd2
16 + 12v
4 and 5 - GND

Once you get a connection with JBBE, then build CAS and ELV and KOMBI wink2


Attached Files Thumbnail(s)
   
Quote this message in a reply
[+] 1 user says Thank You to wxwwxw for this post
22-10-2018, 03:56 AM,
Post: #19
RE: cas / cluster bench setup
ok i have the JBBE connected as posted above. whats best method to use to test if im getting connection via OBD2. using inpa?

again thanks for everyones post helping, still learning and hoping this post will help others too
Quote this message in a reply
22-10-2018, 14:20 PM,
Post: #20
RE: cas / cluster bench setup
(22-10-2018, 03:56 AM)Cniksor Wrote:  ok i have the JBBE connected as posted above. whats best method to use to test if im getting connection via OBD2. using inpa?

again thanks for everyones post helping, still learning and hoping this post will help others too

Connect like in the picture wink2

It cost me a lot of time crying


Attached Files Thumbnail(s)
   
Quote this message in a reply
[+] 5 users say Thank You to wxwwxw for this post


Possibly Related Threads…
Thread Author Replies Views Last Post
XZBMW Tool for bench read 8hp Garryq 9 1,569 26-03-2024, 09:32 AM
Last Post: skywoker
XZBMW F80 Cluster - setup iskullbox 2 268 25-03-2024, 14:38 PM
Last Post: Unspec
  Bosch MEVD172H bench backup mrproper 1 249 23-03-2024, 18:43 PM
Last Post: Ratnik1990
  BMW E87 swap M5 V10 coding cluster Pedrom92 0 99 20-03-2024, 22:50 PM
Last Post: Pedrom92
  BMW G02 NBT need FSC instrument cluster swap Mr.Tester 1 126 07-03-2024, 21:10 PM
Last Post: painsage
  BMW g30 MID cluster in g20 help Pedrom92 1 145 07-03-2024, 00:08 AM
Last Post: Pedrom92
XZBMW ESys Launcher PRO Setup 2.8.1 fengyonghua21 400 47,120 28-02-2024, 09:39 AM
Last Post: Pommie
XZBMW ENAV2 bench activation Airbus 10 799 25-02-2024, 08:17 AM
Last Post: jb2005
XZBMW ISTA...setup macchief 17 1,175 17-02-2024, 20:33 PM
Last Post: macchief
  Motronic 3.3.1 bench jaramillo 3 174 13-02-2024, 05:12 AM
Last Post: 2013m5

Forum Jump:


Users browsing this thread:
3 Guest(s)

Return to TopReturn to Content