Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

cas / cluster bench setup
23-01-2019, 18:43 PM,
Post: #81
RE: cas / cluster bench setup
(22-01-2019, 23:11 PM)Impac Wrote:  
(21-01-2019, 20:40 PM)Cowboy Wrote:  I added FRM to my bench with modules, and tested the set with another CAS 2. Everything works. smile

Can you post which pins you used for FRM?
hi
FRM module :
connector X14260-51-pin, black:
Pin 2=KL30
Pin 47=Ground
Pin 45=K-bus signal/Connect to :JBBF Pin 10 CAN-bus connector (connector X14271-54-pin, blue)
Pin 46=K-bus signal/Connect to :JBBF Pin 46 CAN-bus connector (connector X14271-54-pin, blue)
connector X14261-51-pin, black
Pin 1=KL30
Pin 3=KL30
Pin 34=KL30
Pin 18=Ground
Pin 33=Ground
Pin 12=Supply, terminal 15/ Connect to: CAS Pin 14 (connector X13376-41-pin, black)
Greetings!
Quote this message in a reply
[+] 1 user says Thank You to Cowboy for this post
01-02-2019, 09:35 AM,
Post: #82
RE: cas / cluster bench setup
Strange. I removed my ELV. The set up still works!!
Quote this message in a reply
25-03-2019, 22:04 PM,
Post: #83
RE: cas / cluster bench setup
Hi,
if OBD port from newer models (e.g. E90) with 120Ohm resistor inside is required? I've got OBD from E46 , but there is a resistor on cover, so I assume there is no any other inside.

Only BMW services:

Remote coding/programming - E, F, G serie
HDD change, Carplay, Screen mirroring activation
FSC pack - CIC, NBT, NBT EVO, ENTRYNAV2, MGU, KAFAS
Remote reset 8HP ISN F serie
ELV disable for CAS3, 3+
Quote this message in a reply
25-08-2019, 14:07 PM,
Post: #84
RE: cas / cluster bench setup
I made the bench setup from page 5 the updated one. it works but my key wont stay in, it pops out when i let it go. any idea?
Quote this message in a reply
25-08-2019, 14:36 PM,
Post: #85
RE: cas / cluster bench setup
The key holder or CAS is corrupted or your CAS not receiving the power supply

Only BMW services:

Remote coding/programming - E, F, G serie
HDD change, Carplay, Screen mirroring activation
FSC pack - CIC, NBT, NBT EVO, ENTRYNAV2, MGU, KAFAS
Remote reset 8HP ISN F serie
ELV disable for CAS3, 3+
Quote this message in a reply
26-08-2019, 07:09 AM,
Post: #86
RE: cas / cluster bench setup
(23-01-2019, 18:43 PM)Cowboy Wrote:  
(22-01-2019, 23:11 PM)Impac Wrote:  
(21-01-2019, 20:40 PM)Cowboy Wrote:  I added FRM to my bench with modules, and tested the set with another CAS 2. Everything works. smile

Can you post which pins you used for FRM?
hi
FRM module :
connector X14260-51-pin, black:
Pin 2=KL30
Pin 47=Ground
Pin 45=K-bus signal/Connect to :JBBF Pin 10 CAN-bus connector (connector X14271-54-pin, blue)
Pin 46=K-bus signal/Connect to :JBBF Pin 46 CAN-bus connector (connector X14271-54-pin, blue)
connector X14261-51-pin, black
Pin 1=KL30
Pin 3=KL30
Pin 34=KL30
Pin 18=Ground
Pin 33=Ground
Pin 12=Supply, terminal 15/ Connect to: CAS Pin 14 (connector X13376-41-pin, black)
Greetings!

The assignment is for which FRM module?

Kombiinstrumente nullen, G-Key für F-Modelle, FRM3 Reparatur, EGS 8HP ISN löschen, Benutzter Schlüssel löschen, Schlüssel für EWS / CAS / FEM / BDC, Klonen EWS / CAS / FEM / BDC, Tempolimit Info, GTS Software für M2 / 3/4, Fxx Gxx Alpina Getriebesoftware, uvm ..
Quote this message in a reply
26-08-2019, 16:24 PM,
Post: #87
RE: cas / cluster bench setup
(26-08-2019, 07:09 AM)Stromag Wrote:  
(23-01-2019, 18:43 PM)Cowboy Wrote:  
(22-01-2019, 23:11 PM)Impac Wrote:  
(21-01-2019, 20:40 PM)Cowboy Wrote:  I added FRM to my bench with modules, and tested the set with another CAS 2. Everything works. smile

Can you post which pins you used for FRM?
hi
FRM module :
connector X14260-51-pin, black:
Pin 2=KL30
Pin 47=Ground
Pin 45=K-bus signal/Connect to :JBBF Pin 10 CAN-bus connector (connector X14271-54-pin, blue)
Pin 46=K-bus signal/Connect to :JBBF Pin 46 CAN-bus connector (connector X14271-54-pin, blue)
connector X14261-51-pin, black
Pin 1=KL30
Pin 3=KL30
Pin 34=KL30
Pin 18=Ground
Pin 33=Ground
Pin 12=Supply, terminal 15/ Connect to: CAS Pin 14 (connector X13376-41-pin, black)
Greetings!

The assignment is for which FRM module?

You can check connection pinouts for specific FRM here: newtis.com

Only BMW services:

Remote coding/programming - E, F, G serie
HDD change, Carplay, Screen mirroring activation
FSC pack - CIC, NBT, NBT EVO, ENTRYNAV2, MGU, KAFAS
Remote reset 8HP ISN F serie
ELV disable for CAS3, 3+
Quote this message in a reply
[+] 1 user says Thank You to Matthew53 for this post
26-08-2019, 16:42 PM,
Post: #88
RE: cas / cluster bench setup
(26-08-2019, 16:24 PM)Matthew53 Wrote:  
(26-08-2019, 07:09 AM)Stromag Wrote:  
(23-01-2019, 18:43 PM)Cowboy Wrote:  
(22-01-2019, 23:11 PM)Impac Wrote:  
(21-01-2019, 20:40 PM)Cowboy Wrote:  I added FRM to my bench with modules, and tested the set with another CAS 2. Everything works. smile

Can you post which pins you used for FRM?
hi
FRM module :
connector X14260-51-pin, black:
Pin 2=KL30
Pin 47=Ground
Pin 45=K-bus signal/Connect to :JBBF Pin 10 CAN-bus connector (connector X14271-54-pin, blue)
Pin 46=K-bus signal/Connect to :JBBF Pin 46 CAN-bus connector (connector X14271-54-pin, blue)
connector X14261-51-pin, black
Pin 1=KL30
Pin 3=KL30
Pin 34=KL30
Pin 18=Ground
Pin 33=Ground
Pin 12=Supply, terminal 15/ Connect to: CAS Pin 14 (connector X13376-41-pin, black)
Greetings!

The assignment is for which FRM module?

You can check connection pinouts for specific FRM here: newtis.com

I just wanted to know if this assignment is for the FRM3 or FRM2 ..?

 And if the occupancy for FRM3 and FRM2 is different .. smile

Kombiinstrumente nullen, G-Key für F-Modelle, FRM3 Reparatur, EGS 8HP ISN löschen, Benutzter Schlüssel löschen, Schlüssel für EWS / CAS / FEM / BDC, Klonen EWS / CAS / FEM / BDC, Tempolimit Info, GTS Software für M2 / 3/4, Fxx Gxx Alpina Getriebesoftware, uvm ..
Quote this message in a reply
26-08-2019, 16:48 PM,
Post: #89
RE: cas / cluster bench setup
(26-08-2019, 16:42 PM)Stromag Wrote:  
(26-08-2019, 16:24 PM)Matthew53 Wrote:  
(26-08-2019, 07:09 AM)Stromag Wrote:  
(23-01-2019, 18:43 PM)Cowboy Wrote:  
(22-01-2019, 23:11 PM)Impac Wrote:  Can you post which pins you used for FRM?
hi
FRM module :
connector X14260-51-pin, black:
Pin 2=KL30
Pin 47=Ground
Pin 45=K-bus signal/Connect to :JBBF Pin 10 CAN-bus connector (connector X14271-54-pin, blue)
Pin 46=K-bus signal/Connect to :JBBF Pin 46 CAN-bus connector (connector X14271-54-pin, blue)
connector X14261-51-pin, black
Pin 1=KL30
Pin 3=KL30
Pin 34=KL30
Pin 18=Ground
Pin 33=Ground
Pin 12=Supply, terminal 15/ Connect to: CAS Pin 14 (connector X13376-41-pin, black)
Greetings!

The assignment is for which FRM module?

You can check connection pinouts for specific FRM here: newtis.com

I just wanted to know if this assignment is for the FRM3 or FRM2 ..?

 And if the occupancy for FRM3 and FRM2 is different .. smile

Yes, that's why I gave you the site to verify this pinouts by VIN or model. It's always good to verify it with newtis, even if you have everything right here.

Only BMW services:

Remote coding/programming - E, F, G serie
HDD change, Carplay, Screen mirroring activation
FSC pack - CIC, NBT, NBT EVO, ENTRYNAV2, MGU, KAFAS
Remote reset 8HP ISN F serie
ELV disable for CAS3, 3+
Quote this message in a reply
25-02-2022, 11:47 AM,
Post: #90
RE: cas / cluster bench setup
Hi Guys
i have a Bench with JBBFE2/CAS3 without ELV. I have some Connectors on it for example, FRM, Kombi, Headunit. Everything is working well.
Today i tried to Connect LM2, in Inpa i can see it but i dont have communication to the Module. I have the SSD for a compatible Car in NCS, so this is not the Problem.
Pin 9 12V
Pin 47 12V
Pin 56 GND
Pin 57 GND
Pin 31 12V/Wakeup

Any Ideas? Nor impossible?
Quote this message in a reply


Possibly Related Threads…
Thread Author Replies Views Last Post
XZBMW Tool for bench read 8hp Garryq 9 1,556 26-03-2024, 09:32 AM
Last Post: skywoker
XZBMW F80 Cluster - setup iskullbox 2 264 25-03-2024, 14:38 PM
Last Post: Unspec
  Bosch MEVD172H bench backup mrproper 1 248 23-03-2024, 18:43 PM
Last Post: Ratnik1990
  BMW E87 swap M5 V10 coding cluster Pedrom92 0 97 20-03-2024, 22:50 PM
Last Post: Pedrom92
  BMW G02 NBT need FSC instrument cluster swap Mr.Tester 1 125 07-03-2024, 21:10 PM
Last Post: painsage
  BMW g30 MID cluster in g20 help Pedrom92 1 144 07-03-2024, 00:08 AM
Last Post: Pedrom92
XZBMW ESys Launcher PRO Setup 2.8.1 fengyonghua21 400 47,061 28-02-2024, 09:39 AM
Last Post: Pommie
XZBMW ENAV2 bench activation Airbus 10 793 25-02-2024, 08:17 AM
Last Post: jb2005
XZBMW ISTA...setup macchief 17 1,168 17-02-2024, 20:33 PM
Last Post: macchief
  Motronic 3.3.1 bench jaramillo 3 172 13-02-2024, 05:12 AM
Last Post: 2013m5

Forum Jump:


Users browsing this thread:
3 Guest(s)

Return to TopReturn to Content