[smallnet]

are you installing FSC patch, or FSC oem?

Great! Your .bin has successfully installed all FSCs automatically.
I used HUTool 2.6 before, and it can be done limited.....

I always thought that "HU_SPECIAL_NBTEVO_REPAIR_NAND" was able to lift the restrictions of Compoent Protection. It seems that my understanding is wrong~

I am curious, do you have to rely on the .bin file to remove the CP restriction? Is there any other SSH command or _DEV_UDS.prg that can be done?

Duckdonald, thank you very much. 

[bmwcoder75]

Still no luck for me

1. I deleted manually Component Protection using SSH
2. Erased IPC partition/eeprom (that process also deleted VIN number)
3. Went back to istep 59

Still wont load FSC files.

Now I just noticed, right after I load a fsc file, Component Protection becomes active. WTH.

Is this unit VIN locked now?
This is the 3rd VIN I am using on that unit.

Any idea?

[smallnet]

My HU Component Protecton is active now, i can not remove it. 

0xB7F87A   Komponentenschutz aktiv
  Testbedingungen erfüllt
  Fehler gespeichert
  Fehler würde kein Aufleuchten einer Warnlampe verursachen
  This is no event DTC. This ecu IS RESPONSIBLE for this error entry.
Error code: B7 F8 7A 68

Maybe I need to use BIN to remove component protection (because I don't know what Shell Script can do), if you have .bin or other solutions, please PM me pricing 

[duckdonald]

you can use the .bin that I had already given you.
with that you can remove CP.

[smallnet]

you can use the .bin that I had already given you.
with that you can remove CP.

I have used and tried it several times, but the CP is still activated. ( all fsc is accepted )
I also tried to clear the fault code using Tool32 and ISTA+.
In addition, the problem about blank screen after animation is still there, so I don't know how to continue.

[bmwcoder75]

you can use the .bin that I had already given you.
with that you can remove CP.

I have used and tried it several times, but the CP is still activated. ( all fsc is accepted )
I also tried to clear the fault code using Tool32 and ISTA+.
In addition, the problem about blank screen after animation is still there, so I don't know how to continue.

If all FSC are accepted that means CP is not active, bit confusing your statement, unless I missed something
Blank screen is typical of badly performed region changed units. Tricky to fix. Might need to install a new chip. Someone will help you hopefully, I can't help to fix this particular issue I am afraid.

[smallnet]

If all FSC are accepted that means CP is not active, bit confusing your statement, unless I missed something
Blank screen is typical of badly performed region changed units. Tricky to fix. Might need to install a new chip. Someone will help you hopefully, I can't help to fix this particular issue I am afraid.

This function should not need to replace chip?
(I don't have this software, just the pictures I took on the website.)

[bmwcoder75]

If all FSC are accepted that means CP is not active, bit confusing your statement, unless I missed something
Blank screen is typical of badly performed region changed units. Tricky to fix. Might need to install a new chip. Someone will help you hopefully, I can't help to fix this particular issue I am afraid.

This function should not need to replace chip?
(I don't have this software, just the pictures I took on the website.)

As far as I know this would only perform a partial change. DVD region won't be changed in the process with that script. Same problem with FSCMAP etc.

[hugo325]

Hello,

I have exactly the same problem, when I read the error codes with Esys I have the following values:
63->F4 59 02 7F B7 F8 05 2F B7 F8 09 2F B7 F8 50 2F B7 F8 B8 2F B7 F8 1A 2F B7 F8 E5 2F B7 F8 7A 2F

B7 F8 7A = Component protection

I manage to load the FSC files with Esys, the navigation is active during 3, 4 minutes and then I lose all the options. When I read the status FSC all are in the state "canceled".

Does anyone have a solution to correct this problem?

[duckdonald]

You have FSC oem, or FSC custom?