Please make sure you read Rules! and DO NOT upload/post any illegal softwares or Pirated Material , Thank you for understanding :)
  1. AutoHex II

  2. FemtoEVO



Solved ✔ NBT EVO HW4.1 on the bench
10-12-2018, 10:38 AM, (This post was last modified: 12-01-2019, 16:38 PM by Clusters.)
Post: #1
NBT EVO HW4.1 on the bench
Hi,

I have a NBT EVO HW4.1 and i try to flash it on the bench.

For that i have made my own cables for the quadlock (including ETH_A with 1kOHM to 12v) and the OABR cable, and bought a USB to CAN.

When i send the wake-up message 0x12F 37 7C 8A DD D4 05 33 06 and/or 0x130 45 40 22 8F FE the unit wake-up. But i can ping it (169.254.199.99) for 40s only then the unit goes into sleep mode few seconds, then wake-up 40s, then sleep, and again and again. The screen (8.8" Touch screen) remains black and the fan does not start.

So it seems like there is a need for another message to maintain the unit awake.

Has anyone ever had this case and solved it?

Thank you.
11-12-2018, 00:04 AM,
Post: #2
RE: NBT EVO HW4.1 on the bench
For EVO use iDrive controller or send this ID 563 00 00 00 00 FF FF 00 63
Good luck!
[+] 1 user says Thank You to Vias for this post
13-12-2018, 17:24 PM,
Post: #3
RE: NBT EVO HW4.1 on the bench
I have made some tests and nothing change with the message ID 0x563.
The iDrive contoller is always connected, with or without, nothing change

At the end, i tested with random message and the result is always the same: wake-up 40s, then sleep, wake-up 40s, then sleep, and again and again

What's happen ?
13-12-2018, 20:28 PM,
Post: #4
RE: NBT EVO HW4.1 on the bench
maybe better get a cas + zgw or fem?

NEWportal.fscmap.com online geration VO/FA by VIN, FSC sets, MGU ViM , FSC for Map Updates ROUTE / EVO / CIC / CHAMP / NBT 
MGU (ID7) Video in Motion by FemtoEVO
FSC SETS for BMW NBT|NBTEVO any Hardware including ALPINE (18-11-***, 19-03-*** is also supported)
NBTEVO Carplay, Carplay Fullscreen, E-SYS coding error FIX, Fade to black screen FIX
NBTEVO Region Change (US to China, US to ECE, Japan to India, etc.) NO need to disassemble anything
Remote connection / TeamViewer is NOT required, you will receive the files and will be able to use it at any time.
FEMTO OBD Flasher for MDG1 - Tuning for new BMW F & G series.
REMOTE OBD Tuning for all BMW F&G  EDC17/MEVD17/MG1/MD1 ECU.
RTTI for NBT over Bluetooth.
From real Developers with good online support.
SEND US P.M.
13-12-2018, 20:58 PM, (This post was last modified: 13-12-2018, 21:01 PM by BugFix.)
Post: #5
RE: NBT EVO HW4.1 on the bench
just ZGW + 0x130 + 0x12F + 0x2F4 + 0x2F7 will be good for F series coded EVO
for G series a few to add

NBTEVO ALPINE and HARMAN - activation Navi, CarPlay , CarPlay Full Screen , APPS , Video in motion
HU-MGU ID7 -  Video in motion.


13-12-2018, 22:07 PM, (This post was last modified: 13-12-2018, 22:14 PM by Vias.)
Post: #6
RE: NBT EVO HW4.1 on the bench
Well guys, I send only this two massage:
12F 37 7C 8A DD D4 05 33 06
563 00 00 00 00 FF FF 00 63
Only EVO+Laptop+Ethernet Cable+CanSender+Supply Power 12v and it work good for Flash, Code and play with it!
I don't use ID 130 and ID 267 or any other.

What is interval you use, more 100 ms? Are you have resistor 120 om in your CAN sender?
13-12-2018, 22:31 PM,
Post: #7
RE: NBT EVO HW4.1 on the bench
NM2_BODY_CAN
1379 (563h) - NBTevo_Rueko [21] {aktiv bei: KL_30B}

Zykluszeit: ttyp = 640.0 ms (tmin = 608.0 ms, tmax = 672.0 ms)
Aktivbedingung = KL_30
Startbedingung = KL_30_ON; Stopbedingung = KL_30_OFF

NBTEVO ALPINE and HARMAN - activation Navi, CarPlay , CarPlay Full Screen , APPS , Video in motion
HU-MGU ID7 -  Video in motion.


14-12-2018, 21:04 PM, (This post was last modified: 14-12-2018, 21:15 PM by BugFix.)
Post: #8
RE: NBT EVO HW4.1 on the bench
(13-12-2018, 22:07 PM)Vias Wrote:  Well guys, I send only this two massage:
12F 37 7C 8A DD D4 05 33 06
563 00 00 00 00 FF FF 00 63
Only EVO+Laptop+Ethernet Cable+CanSender+Supply Power 12v and it work good for Flash, Code and play with it!
I don't use ID 130 and ID 267 or any other.

What is interval you use, more 100 ms? Are you have resistor 120 om in your CAN sender?


What you mean about 267 ?

ID267=OP_PENC_OPEL_FRONT (Bedienung Tastgeber Bedienelement Front), ZBE

267 - it is just buttons from i-drive controller

(10-12-2018, 10:38 AM)Coding34 Wrote:  For that i have made my own cables for the quadlock (including ETH_A with 1kOHM to 12v) ,
Haveto disconnect that fake

NBTEVO ALPINE and HARMAN - activation Navi, CarPlay , CarPlay Full Screen , APPS , Video in motion
HU-MGU ID7 -  Video in motion.


15-12-2018, 16:07 PM, (This post was last modified: 15-12-2018, 16:09 PM by billyballs.)
Post: #9
RE: NBT EVO HW4.1 on the bench
BugFix where do you get the info from the CAN bus ?

I mean this:

(14-12-2018, 21:04 PM)BugFix Wrote:  ID267=OP_PENC_OPEL_FRONT (Bedienung Tastgeber Bedienelement Front), ZBE

and this:

(13-12-2018, 22:31 PM)BugFix Wrote:  NM2_BODY_CAN
1379 (563h) - NBTevo_Rueko [21] {aktiv bei: KL_30B}

Zykluszeit: ttyp = 640.0 ms (tmin = 608.0 ms, tmax = 672.0 ms)
Aktivbedingung = KL_30
Startbedingung = KL_30_ON; Stopbedingung = KL_30_OFF
15-12-2018, 17:47 PM,
Post: #10
RE: NBT EVO HW4.1 on the bench
Google work fine for me

NBTEVO ALPINE and HARMAN - activation Navi, CarPlay , CarPlay Full Screen , APPS , Video in motion
HU-MGU ID7 -  Video in motion.




Possibly Related Threads...
Thread Author Replies Views Last Post
  G30 6WB ignition on bench with F series FEM Levanime 0 77 Yesterday, 23:29 PM
Last Post: Levanime
XZBMW Bench ZGW01 MOST Routing CryptMan 4 217 Yesterday, 20:05 PM
Last Post: dumitru.o
  Bench Coding - Need help on required components TokenMaster 20 1,065 20-07-2019, 16:52 PM
Last Post: alblue
XZBMW TV on cic e92 bench setup ccfj1 9 343 17-07-2019, 07:16 AM
Last Post: ccfj1
XZBMW E70 EMF control on Bench BMWDriver999 4 296 10-07-2019, 12:06 PM
Last Post: BMWDriver999
  ICAM will not code on the Bench Mizta Insane 9 430 30-06-2019, 14:46 PM
Last Post: Mizta Insane
  Bench flashing E70 TRSVC Freddy1 2 134 27-06-2019, 10:11 AM
Last Post: Freddy1
XZBMW NBT EVO id4 flash error (Bench system) acdangsh 9 426 18-06-2019, 15:38 PM
Last Post: bmwcoder75
XZBMW Flashing ZGW 1 to ZGW 2 & CIC & NBT bench test, Please help nguyennhatquang 38 21,363 14-06-2019, 11:54 AM
Last Post: rickynguyen
  FEM on bench - KL15_ein problem osd 9 2,571 08-06-2019, 16:44 PM
Last Post: pshoey

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content