Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Solved ✔ NBT EVO HW4.1 on the bench
10-12-2018, 10:38 AM,
(This post was last modified: 12-01-2019, 16:38 PM by Clusters.)
Post: #1
|
|||
|
|||
NBT EVO HW4.1 on the bench
Hi,
I have a NBT EVO HW4.1 and i try to flash it on the bench. For that i have made my own cables for the quadlock (including ETH_A with 1kOHM to 12v) and the OABR cable, and bought a USB to CAN. When i send the wake-up message 0x12F 37 7C 8A DD D4 05 33 06 and/or 0x130 45 40 22 8F FE the unit wake-up. But i can ping it (169.254.199.99) for 40s only then the unit goes into sleep mode few seconds, then wake-up 40s, then sleep, and again and again. The screen (8.8" Touch screen) remains black and the fan does not start. So it seems like there is a need for another message to maintain the unit awake. Has anyone ever had this case and solved it? Thank you. |
|||
11-12-2018, 00:04 AM,
Post: #2
|
|||
|
|||
RE: NBT EVO HW4.1 on the bench
For EVO use iDrive controller or send this ID 563 00 00 00 00 FF FF 00 63
Good luck! |
|||
13-12-2018, 17:24 PM,
Post: #3
|
|||
|
|||
RE: NBT EVO HW4.1 on the bench
I have made some tests and nothing change with the message ID 0x563.
The iDrive contoller is always connected, with or without, nothing change At the end, i tested with random message and the result is always the same: wake-up 40s, then sleep, wake-up 40s, then sleep, and again and again What's happen ? |
|||
13-12-2018, 20:28 PM,
Post: #4
|
|||
|
|||
RE: NBT EVO HW4.1 on the bench
maybe better get a cas + zgw or fem?
FSCMap -> FemtoEVO
portal.femtoevo.com online geration VO/FA by VIN, FSC sets, MGU ViM , FSC for Map Updates ROUTE / EVO / CIC / CHAMP / NBT MD1/MG1 06.2020+ DME unlocking services. 1CR Enable for 06.2020+ EU cars (G series, petrol/DIESEL - RU only). NCD sign for coding 2.0 for selected portal users. instagram: @femtoevo |
|||
13-12-2018, 20:58 PM,
(This post was last modified: 13-12-2018, 21:01 PM by BugFix.)
Post: #5
|
|||
|
|||
RE: NBT EVO HW4.1 on the bench
just ZGW + 0x130 + 0x12F + 0x2F4 + 0x2F7 will be good for F series coded EVO
for G series a few to add NBTEVO, ENAV2, MGU - CP OFF, Navi , APPS , Carplay, AA
MGU ID-8-9-10 Cars - Full Region change NCD Secure Coding 2.0 |
|||
13-12-2018, 22:07 PM,
(This post was last modified: 13-12-2018, 22:14 PM by Vias.)
Post: #6
|
|||
|
|||
RE: NBT EVO HW4.1 on the bench
Well guys, I send only this two massage:
12F 37 7C 8A DD D4 05 33 06 563 00 00 00 00 FF FF 00 63 Only EVO+Laptop+Ethernet Cable+CanSender+Supply Power 12v and it work good for Flash, Code and play with it! I don't use ID 130 and ID 267 or any other. What is interval you use, more 100 ms? Are you have resistor 120 om in your CAN sender? |
|||
13-12-2018, 22:31 PM,
Post: #7
|
|||
|
|||
RE: NBT EVO HW4.1 on the bench
NM2_BODY_CAN
1379 (563h) - NBTevo_Rueko [21] {aktiv bei: KL_30B} Zykluszeit: ttyp = 640.0 ms (tmin = 608.0 ms, tmax = 672.0 ms) Aktivbedingung = KL_30 Startbedingung = KL_30_ON; Stopbedingung = KL_30_OFF NBTEVO, ENAV2, MGU - CP OFF, Navi , APPS , Carplay, AA
MGU ID-8-9-10 Cars - Full Region change NCD Secure Coding 2.0 |
|||
14-12-2018, 21:04 PM,
(This post was last modified: 14-12-2018, 21:15 PM by BugFix.)
Post: #8
|
|||
|
|||
RE: NBT EVO HW4.1 on the bench
(13-12-2018, 22:07 PM)Vias Wrote: Well guys, I send only this two massage: What you mean about 267 ? ID267=OP_PENC_OPEL_FRONT (Bedienung Tastgeber Bedienelement Front), ZBE 267 - it is just buttons from i-drive controller (10-12-2018, 10:38 AM)Coding34 Wrote: For that i have made my own cables for the quadlock (including ETH_A with 1kOHM to 12v) ,Haveto disconnect that fake NBTEVO, ENAV2, MGU - CP OFF, Navi , APPS , Carplay, AA
MGU ID-8-9-10 Cars - Full Region change NCD Secure Coding 2.0 |
|||
15-12-2018, 16:07 PM,
(This post was last modified: 15-12-2018, 16:09 PM by billyballs.)
Post: #9
|
|||
|
|||
RE: NBT EVO HW4.1 on the bench
BugFix where do you get the info from the CAN bus ?
I mean this: (14-12-2018, 21:04 PM)BugFix Wrote: ID267=OP_PENC_OPEL_FRONT (Bedienung Tastgeber Bedienelement Front), ZBE and this: (13-12-2018, 22:31 PM)BugFix Wrote: NM2_BODY_CAN |
|||
15-12-2018, 17:47 PM,
Post: #10
|
|||
|
|||
RE: NBT EVO HW4.1 on the bench
Google work fine for me
NBTEVO, ENAV2, MGU - CP OFF, Navi , APPS , Carplay, AA
MGU ID-8-9-10 Cars - Full Region change NCD Secure Coding 2.0 |
|||
« Next Oldest | Next Newest »
|
Possibly Related Threads… | |||||
Thread | Author | Replies | Views | Last Post | |
MGU Bench connection | kimz | 4 | 417 |
22-04-2024, 17:06 PM Last Post: kimz |
|
Test bench Connection to CAN ECU's | HaakonA | 3 | 312 |
03-04-2024, 07:24 AM Last Post: sixcode |
|
Tool for bench read 8hp | Garryq | 9 | 1,668 |
26-03-2024, 09:32 AM Last Post: skywoker |
|
Bosch MEVD172H bench backup | mrproper | 1 | 278 |
23-03-2024, 18:43 PM Last Post: Ratnik1990 |
|
ENAV2 bench activation | Airbus | 10 | 956 |
25-02-2024, 08:17 AM Last Post: jb2005 |
|
Motronic 3.3.1 bench | jaramillo | 3 | 214 |
13-02-2024, 05:12 AM Last Post: 2013m5 |
|
Dde Coding/flash with esys in bench? | ruben_17non | 0 | 203 |
08-02-2024, 21:28 PM Last Post: ruben_17non |
|
Entrynav2 - Trying to Trigger Component Protection on Bench | 2002JCW | 5 | 564 |
30-01-2024, 16:44 PM Last Post: DEJMIEN |
|
NBT display on bench without unit | djordan | 4 | 365 |
15-01-2024, 08:08 AM Last Post: Powerlab |
|
cas / cluster bench setup | Cniksor | 103 | 24,405 |
09-01-2024, 09:43 AM Last Post: MIKUr1 |
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content