Please make sure you read Rules! and DO NOT upload/post any illegal softwares or Pirated Material , Thank you for understanding :)
  1. AutoHex II

  2. FemtoEVO



ccc bench wake up
29-12-2018, 23:51 PM,
Post: #1
ccc bench wake up
I have ccc+cid+con and usb>can interface.
What exactly it has to receive to wake up and to stay active all these units? Only 0x130 with 100ms or some others as well?
Quote this message in a reply
30-12-2018, 11:43 AM,
Post: #2
RE: ccc bench wake up
Question - to get cid working, do i need some other modules?
Because when units are starting i see backlight of CID turns on for 1sec and goes off.
Quote this message in a reply
05-01-2019, 19:34 PM,
Post: #3
RE: ccc bench wake up
(30-12-2018, 11:43 AM)zero9 Wrote:  Question - to get cid working, do i need some other modules?
Because when units are starting i see backlight of CID turns on for 1sec and goes off.
you need cas modulo and Key. try out with a E65 CAs, it has the key included
Quote this message in a reply
11-01-2019, 17:52 PM,
Post: #4
RE: ccc bench wake up
You can try this :
id = 0x12F, len = 8, data = 8C 50 8A DD F4 5 30 6 each 100MS
Quote this message in a reply
12-01-2019, 17:31 PM,
Post: #5
XZBMW  RE: ccc bench wake up
(11-01-2019, 17:52 PM)ashrafpts Wrote:  You can try this :
id = 0x12F, len = 8, data = 8C 50 8A DD F4 5 30 6 each 100MS

Hi ashrafpts, do you know also the message to wakeup CHAMP2?

I used the one for NBT and this your for CIC, but no one seems able to wakeup my CHAMP2.

Thanks


If I helped you, please hit the Thanks button and leave Reputation[Image: under.gif]
Quote this message in a reply
15-01-2019, 16:21 PM,
Post: #6
RE: ccc bench wake up
try to use the 2 messages ( 0x130 & 0x12F ) at same time , as i know one message is to wakeup the module and the other one is to keep it live ( not to go to sleep mode )
Quote this message in a reply
06-02-2019, 06:12 AM,
Post: #7
RE: ccc bench wake up
Hi,

Do I need connect cid and con to work with CCC on bench?
I connect power and CAN Bus, I close MOST ring.

The only module that I can connect is gateway, rest show IFH-9 error.
I thing CCC is reseting because I hear from time to time CD drive.

But maybe I need to connect CID and Controler to work?

If I helped, please magic buttons thx+rep yes yes yes under under under
Quote this message in a reply
06-02-2019, 12:49 PM,
Post: #8
RE: ccc bench wake up
Hello i have normal bench without can emu and ccc wiring i too only can connect to gw, cant connect to another most modules where could be problem?
Quote this message in a reply
06-02-2019, 13:40 PM,
Post: #9
RE: ccc bench wake up
How you connect power to ccc?
I connect only:
12V - pin 15
Ground - pin 12.
What aboute pin 14 from LM? It's only for illuminating?

If I helped, please magic buttons thx+rep yes yes yes under under under
Quote this message in a reply
06-02-2019, 14:42 PM,
Post: #10
RE: ccc bench wake up
Yes its ilumination, everythibg conected +- can and most, my icom adapter blinks that with most everythibg good
Quote this message in a reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  ATM - NBT EVO - bench stup - help needed Wibbles 22 1,091 3 hours ago
Last Post: domdel
  How to make a Bench using FEM for DUMMIES Mwahab 33 9,639 Yesterday, 01:54 AM
Last Post: tcp443
XZBMW Flashing ZGW 1 to ZGW 2 & CIC & NBT bench test, Please help nguyennhatquang 37 17,905 16-03-2019, 07:10 AM
Last Post: vasya
  6WB on bench setup X-treme 12 2,087 08-03-2019, 12:51 PM
Last Post: pindour
XZBMW EntryNav2 on bench Weebyx 2 129 03-03-2019, 10:30 AM
Last Post: larshutten
  Bench programming NBT Evo. Vehicle Parked signal? vilord 4 412 22-02-2019, 22:00 PM
Last Post: Weebyx
XZBMW Bench flash ZGW learnaswego 5 412 16-02-2019, 16:40 PM
Last Post: learnaswego
  Flash F-series logic7 amp on bench? vilord 7 315 12-02-2019, 14:15 PM
Last Post: vilord
  FRM3 bench set up need advise koziol 6 653 11-02-2019, 00:00 AM
Last Post: PhilipM
XZBMW BMW E89 CAS 3 bench flashing - Need help KSpeed 14 818 10-02-2019, 23:03 PM
Last Post: Fabiuz

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content