Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

OPCOM "NEW" V1.99 does not communicate with ESC (ECU does not reply, please wait 2 se
02-01-2019, 17:38 PM,
Post: #1
OPCOM "NEW" V1.99 does not communicate with ESC (ECU does not reply, please wait 2 se
Hi guys.
I have Astra G - engine Z16SE.
I bought the OPCOM "NEW" 1.99, on which the Chinese has erased the chip number???

[Image: 7b41ed1079691624.jpg] [Image: 58566e1079691664.jpg]

[Image: dd64f91079691744.jpg] [Image: 5e61031079691834.jpg]

[Image: 003a461079691884.jpg] [Image: 2be4c01079691924.jpg]

[Image: ce68921079691984.jpg] [Image: 7bbcb11079692064.jpg]

I tried many versions of Windows (Windows 7 x64, Windows 7 x86 and virtual Windows XP x86) all the drivers and versions of OP-COM and VAUX-COM that I found, but each time happens error "ECU does not reply, please wait 2 seconds"

The driver is successfully installed and is visible in the device manager as:
(USB Serial Converter - USB \ VID_0403 & PID_6001 & REV_0600) or
(OP COM USB V2 Interface - USB \ VID_0403 & PID_4F50 & REV_0600 - after FTDI reprogramming with MProg 3.5).
The interface test passes successfully, but I can not communicate with the ECU. The device can flashing. I tried firmwarefiles 1.39 and 1.45 without success.
I hope for suggestions.
Best regards!
Quote this message in a reply
02-01-2019, 18:33 PM,
Post: #2
RE: OPCOM "NEW" V1.99 does not communicate with ESC (ECU does not reply, please wait 2 se
Buy another one.
The best old v5 pcb.
Quote this message in a reply
[+] 1 user says Thank You to darek_naprawa for this post
02-01-2019, 18:53 PM, (This post was last modified: 02-01-2019, 18:56 PM by mattydr67.)
Post: #3
RE: OPCOM "NEW" V1.99 does not communicate with ESC (ECU does not reply, please wait 2 se
This one its a good one too.
It has a real Pic18F458
So to be sure that your tool is good try to connect to ABS ot Airbag in same care.
Also you can try to IPC or Radio.
But ABS and Aibag is connection on same pin 7 as Engine ECU.
So first of all you have to be sure that its not an interface hardware issue.
In the rest if you are using opcom china clone its better to have fw1.39 and if you are usibg vauxcom its better to have fw1.45
In the rest all this firmware that chinese advertise are "star dust in our eyes"
Check also if the opcom drivers has no VCP installed.
Good luck
Quote this message in a reply
02-01-2019, 21:07 PM,
Post: #4
RE: OPCOM "NEW" V1.99 does not communicate with ESC (ECU does not reply, please wait 2 se
no
this pcb with firmware v1.99  is not good
recomand to bay a new one
Quote this message in a reply
02-01-2019, 21:20 PM, (This post was last modified: 02-01-2019, 21:23 PM by mattydr67.)
Post: #5
RE: OPCOM "NEW" V1.99 does not communicate with ESC (ECU does not reply, please wait 2 se
Why is not good?
Please details a littel bit.
It has a real MCU ( Pic18F458 )
This is important. All the other hardware issues can be solved easy.
For kline you need L9637D instead of 33390 chines one. And you have to change a A1040 with a A1050 or MCP2551 on HS-CAN
In the rest why you consider it so bad?
Good luck
Quote this message in a reply
02-01-2019, 21:53 PM,
Post: #6
RE: OPCOM "NEW" V1.99 does not communicate with ESC (ECU does not reply, please wait 2 se
i have this version firmware 1.99 and if you make firmware updata , no comunication with car
no real pic
Quote this message in a reply
03-01-2019, 06:17 AM, (This post was last modified: 03-01-2019, 06:22 AM by mattydr67.)
Post: #7
RE: OPCOM "NEW" V1.99 does not communicate with ESC (ECU does not reply, please wait 2 se
He is the only one who can test this.
As I can see from his pics the hardware looks as it has a real MCU there. There's no C23 and D5 which are specific for fake MCU.
Then if after an upgrade/downgrade the firmware your interface test its OK and you can see the the firmware version change you have a good real MCU.
Good luck
Quote this message in a reply
03-01-2019, 14:02 PM,
Post: #8
RE: OPCOM "NEW" V1.99 does not communicate with ESC (ECU does not reply, please wait 2 se
Thanks for the answers guys.
I can not connect to any module on the car, on any pin 3, 7 or 12.
In aliexpress many who buy this version complain that Pic has a deleted number and does not work.
If he's a real Pic18F458 why someone deletes the numbers???
Is there anything else I can try or I have to give up already ;//
Best regards!
Quote this message in a reply
03-01-2019, 15:00 PM, (This post was last modified: 03-01-2019, 15:04 PM by mattydr67.)
Post: #9
RE: OPCOM "NEW" V1.99 does not communicate with ESC (ECU does not reply, please wait 2 se
As I told you this hardware is using a real Pic18F458. You can test like this:
Upgrade and downgrade the firmware using Ocflash?
After each firmware change if you are doing an interface test using opcom/vauxcom do you see the new firmware and test is OK
If yes then the PIC MCU is the corect one.
Maybe the chinese changed the pic18F458 with Pic18F4580 wich work only with fw1.39 and opcom china clone software. But if you try to upgrade/downgrade the firmware ypu will damage it
Check what kline chip do you have. Is it L9637D?
Good luck
Quote this message in a reply
03-01-2019, 16:52 PM,
Post: #10
RE: OPCOM "NEW" V1.99 does not communicate with ESC (ECU does not reply, please wait 2 se
I see that I can no longer flash the device. No upgrade or downgrade. (error "Bootloader did not respond...either killed interface, empty pic or new protection!")
But it still passes the interface test.
Yes, chip is L9637D?

[Image: befaea1080945424.jpg] [Image: a55a691080945404.jpg]
Quote this message in a reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Opcom Motherboard version (can't find USB drivers) BrainBT 5 1,364 17-10-2019, 17:18 PM
Last Post: skyline
  Opcom Bootloader Repair with TL866 ICSP port aki1 3 1,621 07-10-2019, 13:07 PM
Last Post: avepla
  Opcom HQ Installers 2017 Gabriel87 18 10,349 30-09-2019, 22:30 PM
Last Post: AIR0
  opcom clone need help to repair autosolutions 1 814 18-09-2019, 02:40 AM
Last Post: mattydr67
  OPCOM problem conecting CrossMan 22 5,282 02-08-2019, 05:18 AM
Last Post: mattydr67
KOpel OPCOM china for win7 or win10 josef1708 7 4,518 26-06-2019, 22:27 PM
Last Post: MartinB
KOpel Solved! Opcom V1.99 communication error irarkh 23 30,899 07-05-2019, 06:40 AM
Last Post: Sirius83
KOpel Software Opcom Hq v12, v13 ,v15 and Vaux com v13, v16 McMihai 19 12,711 30-12-2018, 22:56 PM
Last Post: Moldovan1
  Opcom for 2011 Astra J Burt_100 1 1,677 09-12-2018, 20:55 PM
Last Post: yudon
  Opcom firmware gyenge 52 31,233 18-11-2018, 17:31 PM
Last Post: Gabriel87

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content