Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
E60 Flash DSC to non-active steering
08-01-2019, 00:41 AM,
Post: #1
|
|||
|
|||
E60 Flash DSC to non-active steering
Hi, I'd like to remove my active steering feature because it's acting up.
Have removed from VO, removed fuse, and blank coded KOMBI. Active steering error gone, but still have spinning circle and brake warning. The last part should be to load non-afs software to the DSC unit, but I don't have the knowledge to winKFP for the task. Have icom and 60.1 daten installed. Looking for remote assistance. Payment offered. |
|||
08-01-2019, 07:23 AM,
Post: #2
|
|||
|
|||
RE: E60 Flash DSC to non-active steering
DSC must be changed not programmed because different Hardware.
|
|||
08-01-2019, 07:56 AM,
Post: #3
|
|||
|
|||
RE: E60 Flash DSC to non-active steering
;ZB-NR TYP-NR HW-NR IX SW-NR AM PIN S CS
6768648,0000000,6768648,A,0000000DA,0FFFFFFFFFD,000,1 6 6768908,0000000,6768908,A,0000000DA,0FFFFFFFFFD,000,1 G 6769705,0000000,6769705,A,0000000DA,0FFFFFFFFFD,000,1 O 6791109,0000000,6791109,A,0000000DA,0FFFFFFFFFD,000,1 E 6777803,0000000,6777803,A,0000000DA,0FFFFFFFFFD,000,1 K 6768616,0000000,6768616,A,0000000DA,0FFFFFFFFFD,000,1 O 6768912,0000000,6768912,A,0000000DA,0FFFFFFFFFD,000,1 I 6769709,0000000,6769709,A,0000000DA,0FFFFFFFFFD,000,1 C 7841983,0000000,7841983,A,0000000DA,0FFFFFFFFFD,000,1 K 7837326,0000000,7837326,A,0000000DA,0FFFFFFFFFD,000,1 W As stated above, no similar hardware number, no chance, must replace DSC with correct hardware type |
|||
08-01-2019, 09:08 AM,
Post: #4
|
|||
|
|||
RE: E60 Flash DSC to non-active steering
after the removal of the active steering, you have to code the whole car, not just the Kombi.
|
|||
08-01-2019, 09:40 AM,
Post: #5
|
|||
|
|||
RE: E60 Flash DSC to non-active steering
Hi, thanks for the advises, though in each directions.
Can you do me a favor and check out this thread https://cartechnology.co.uk/showthread.p...e+steering It's described that one program is with AFS and another is without, for the same hardware. specially this comment leads me to think that I can flash zb even though hardware is not the same: kmodel99 Wrote: Solved, as inotherwords said, I flashed DSC module with software without active steering. WinKFP in Expert Mode was used. Old ZB Number 6769709, new 6769705 |
|||
09-01-2019, 09:49 AM,
Post: #6
|
|||
|
|||
RE: E60 Flash DSC to non-active steering
bumping this.. anyone?
|
|||
09-01-2019, 13:20 PM,
Post: #7
|
|||
|
|||
RE: E60 Flash DSC to non-active steering
remove $217 (Active steering) from the car VO , write new FA changes to CAS and LMA ,
run ISTA-P ( you need this , if you don't have it then download it from the forum ) , run ista-p , if your DSC is compatible with non active steering software then ista-P will give you the new software number ,, otherwise ista-P will ask you to replace DSC module. |
|||
14-01-2019, 09:47 AM,
(This post was last modified: 14-01-2019, 09:48 AM by huzionet.)
Post: #8
|
|||
|
|||
RE: E60 Flash DSC to non-active steering
Just did a Bmw E60 545i and i Confirm this works
I removed $217 from VO/FA and coded default KOMBI, SGM, SZL Than (>> kmodel99<<) Remotely used WINKFP to flash EXPERT MODE i did not want to do this since i have no experience with EXPERT MODE, but after learning from kmodel99 its not that hard. DSC60–>zb#6768648 and default coded DSC.... ORIGINAL ZB# was DSCA60–>6768616 Remove A/S Fuse #4–>40amp Than I just did the Steering Angle Calibration and all good to go. This metod work. AutoKodowanie - coding - programming - navigations - retrofit.
|
|||
15-01-2019, 21:49 PM,
Post: #9
|
|||
|
|||
RE: E60 Flash DSC to non-active steering
is there a tutorial on how to do it step by step? I have the same one e60 545i and i want to get rid of it also
(14-01-2019, 09:47 AM)huzionet Wrote: Just did a Bmw E60 545i and i Confirm this works |
|||
15-01-2019, 23:05 PM,
Post: #10
|
|||
|
|||
RE: E60 Flash DSC to non-active steering
The problem is that you will have DSC interventions in sharp curves. For fully function you will have to flash SZL too and this does not work. I already tried everything and ended up with just letting this shit..
|
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content