Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

Ford Transit calibrating used ECU
16-01-2019, 20:15 PM,
Post: #1
LFord  Ford Transit calibrating used ECU
Hello guys, I think I need a Ford specialist.

The situation is a bit complicated, I'll explain it:
The car is 2013 Ford Transit, 2.2 TDCI. After a damaged engine, they replaced the engine + whole ECU kit (ECU, BCM, Keys, etc.) from an 2010 Transit and the car was running normal, everything worked ok.
Then i used to turn DPF off and killed the ECU in reading attempt, so I have no backup. I bought used ECU with same numbers (labels attached), did PATS initialization and programed the keys with IDS, car started so far. Then I turned DPF off in the software, did the engine adaptations and so on. Now, the car has strange DTC-codes which weren't there before, engine starting is bad, and no power. Could it be, that the calibration file is not for that engine, which is in the used ECU? I would try to reprogram the PCM with IDS, but how to find the right callibration file? I don't have the VIN from the replaced ECU-kit when they replaced with the whole engine, maybe i can find by reading out the BCM. After initialization with PATS, i also found an other VIN in the ECU dump, maybe this is the VIN which I am looking for.

VIN used ECU: WF0XXXTTFXAA71828
maybe VIN ori ECU: WF0XXXTTFXAP13026

Can anybody help me, which are the next steps to program the proper file in the PCM. I have working VCM2 with Ford IDS and callibration files V106, Launch, X17, VVDIprog, Xprog, etc.
If you need more information about the vehicle, I'll check and post.
Many thanks in advance.


Attached Files Thumbnail(s)
       
Quote this message in a reply
17-01-2019, 00:10 AM, (This post was last modified: 17-01-2019, 01:58 AM by xtac1080.)
Post: #2
RE: Ford Transit calibrating used ECU
What codes are you pulling? You say the car ran fine and then you did DPF-off, then it ran poorly. I'd say something went wrong with the DPF-off procedure (damaged EEPROM or poor re-solder)

You can find as-built files for those VINs here:
https://www.motorcraftservice.com/AsBuilt/Details

You can also start IDS without the key on so you will be forced to use the tear tag info off the PCM (no VIN read). I assume the picture is of the new PCM. The tear tag on it is 9HEB. Try that as well. More info here:
https://www.searchautoparts.com/motorage...procedures
Quote this message in a reply
[+] 1 user says Thank You to xtac1080 for this post
17-01-2019, 03:25 AM,
Post: #3
RE: Ford Transit calibrating used ECU
Did you perform a PMI (Programmable Module Installation) and reflash the PCM with the correct software and new VIN number? It doesn't seem like you did that or you didn't mention it here. Need some clarification so we can help you.
Quote this message in a reply
[+] 1 user says Thank You to hasoon2000 for this post
17-01-2019, 17:06 PM, (This post was last modified: 17-01-2019, 17:25 PM by premium89.)
Post: #4
RE: Ford Transit calibrating used ECU
First, many thanks for your answers.
@xtac1080
These DTC i have: P1608, P062B, P0606, P1606. Yes, the car ran fine before, just DPF was bad. I don't think it's because of DPF-procedure, because i didn't tested the car after PCM replace, maybe the issues were there already after replace. I just checked fault memory and did the necessary fuel pump adaptation etc, which the diagnostics showed. I read in circuit with programmer, i think soldering is not the problem.
The link with as-built files is not working. 9HEB is not the tear tag, i tried this already and all other numbers from the ECU label, it did not recognize any car. Even not by typing PCM part number. The third possible number to type in is the callibration number, which i don't have.

@hasoon2000
No i didn't perform that, only went through the PATS functions to start the car. This is my question, I want to now how to get the correct software to reflash the PCM. Can you explain me the procedure?

Many thanks for helping and your time.
Quote this message in a reply
18-01-2019, 00:55 AM, (This post was last modified: 18-01-2019, 01:02 AM by xtac1080.)
Post: #5
RE: Ford Transit calibrating used ECU
They updated the site after I posted the link. Here is the new one:
https://www.motorcraftservice.com/AsBuilt

Only code I could lookup was P0606 as I'm in NA. Quick google search says they are all PCM related codes. I'd start by flashing back to stock, seeing how the truck runs, then proceeding to mess with the flash. 

   
Quote this message in a reply
18-01-2019, 09:36 AM, (This post was last modified: 18-01-2019, 09:38 AM by premium89.)
Post: #6
RE: Ford Transit calibrating used ECU
(18-01-2019, 00:55 AM)xtac1080 Wrote:  They updated the site after I posted the link. Here is the new one:
https://www.motorcraftservice.com/AsBuilt

Only code I could lookup was P0606 as I'm in NA. Quick google search says they are all PCM related codes. I'd start by flashing back to stock, seeing how the truck runs, then proceeding to mess with the flash. 

Ok, i will try that when I am near the truck, but in this procedure, i bought a file from Pro-tuner to turn dpf off. He guarantees me, that the file is OK. I attached i ori and mod here, if sb want to check.
How can I find the proper Tear Tag, or Asbuild information?


Attached Files
Transit ORG and DPFoff.rar
File Type: .rar
Downloaded: 7 times
Size: 580.3 KB

Quote this message in a reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  ford transit bcm Bk2t-14b476-BU - clone / virgin bboctavian 1 66 Yesterday, 13:45 PM
Last Post: bboctavian
LFord Ford S-MAX 2006 gizmo220 1 23 25-03-2024, 22:32 PM
Last Post: toutou_gsm
LFord License for Ford IDS FJDS FRDS until 2025. blerim shehi 5 845 20-03-2024, 08:42 AM
Last Post: WANGUO
  Ford IDS 130.01+Upd 130.04, FDRS 39.6.8, FJDS 130.01+Upd 130.04 + PATCH 1.1.3.1 DoZe 55 11,875 19-03-2024, 00:35 AM
Last Post: DoZe
  Need Wiring Diagram Ford Transit 2.0 ToolSet 4 118 06-03-2024, 21:25 PM
Last Post: ToolSet
LFord FORD MONDEO VBF files rasmoka 1 126 20-02-2024, 18:06 PM
Last Post: fordmidabil
  2012 Ford fusion calibration file koziol 2 74 15-02-2024, 17:02 PM
Last Post: pupu144
LMazda Module Build Data As Built FORD MAZDA Adam0773 76 41,148 13-02-2024, 21:51 PM
Last Post: kautuvera
LFord Ford UCDS 2.0.7.x with UIII PLUS Loader vierchatura 0 178 12-02-2024, 19:04 PM
Last Post: vierchatura
  Ford KA 2 self-teaching trigger wheel Tomate 2 90 25-01-2024, 22:45 PM
Last Post: Tomate

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content