[kuks]

Hi Mates,

I have problem with F56 Mini 2015.
There is seatbelt light on and fault code in kombi:

-KOMB25
0xE114A3
Message (status, seat belt buckle contact, seat occupancy, 0x297) checksum error, receiver KOMBI, transmitter ACSM

ACSM is without fault code.

Wehicle was allready falshed and ACSM was replaced and it is the same.

Thanks

[rana]

"checksum error " mean there wrong with something programming part

[PhilipM]

Try running through a session with ISTA-P and see if that agrees you have the correct software version on the ACSM, and recode things if you haven't tried that.

If it is the wrong module or software, you should see a message to replace or update the ACSM

[Terabyte]

Hello

I have the same problem.

Did you solve it?

[cartermd]

Did you flash ACSM ?

[Terabyte]

Yes I flashed whole car with newest psdzdata

---

I just tried to make new flash of ACSM, but it abortet.


And now I don't get connection to ACSM anymore

ACSM negative response error: Timeout

[walter.linde]

Hi Mates,

I have problem with F56 Mini 2015.
There is seatbelt light on and fault code in kombi:

-KOMB25
0xE114A3
Message (status, seat belt buckle contact, seat occupancy, 0x297) checksum error, receiver KOMBI, transmitter ACSM

ACSM is without fault code.

Wehicle was allready falshed and ACSM was replaced and it is the same.

Thanks

Unfortunately I have the same problem.. no error in ACSM, I used ACSM4i in tool32:
first I run fs_lesen, and fs_loeschen then is_lesen and is_loeschen finally steuergeraete_reset

I've tried also the job STEUERN in custom (ARG;VERRIEGELUNG_SG;0) but when I select "0" it gives me error.

What can I do?

Thanks..

[walter.linde]

Here the tool32 logs:

I N F O R M A T I O N M E M O R Y
---------------------------------------

Date: 10.07.2019, 20:37:03
JobStatus: OKAY
Variant: ACSM4I.PRG
Version: 6.500
-------------------------------------------------------------

RESULT: 1 error in error memory !
-------------------------------------------------------------

0x01A062 DEM_INT_AECU_ASYNCHRON_MODE

Error counter : 1
Healing counter : 255

Absolute time 159379818 s
Mileage 33984 km
BETRIEBSSTUNDENZAEHLER_BEGINN 9770833.00 s
BETRIEBSSTUNDENZAEHLER_ENDE 9770838.00 s
AUSSENTEMPERATUR 29.00 °C
SG_INNENTEMPERATUR -0.10 °C
SYSTEMZUSTAND_PDC: ungueltig 1.500000E+001 0-n
SYSTEMZUSTAND_KLR: KL R ein 1.600000E+001 0-n
SYSTEMZUSTAND_KL_R_W: Wechsel erfolgt 2.560000E+002 0-n
SYSTEMZUSTAND_KL_15: KL 15 ein 4.096000E+003 0-n
SYSTEMZUSTAND_KL_15_W: KL 15 Wechsel erfolgt 6.553600E+004 0-n
SYSTEMZUSTAND_MOT: kein Motorstart 0.000000E+000 0-n
SYSTEMZUSTAND_GESCHW: ungültig 2.516582E+008 0-n
ZEIT_NACH_PWRON 19.00 s
POWER_ON_ZAEHLER 12529.00 count
SG_SPANNUNG 12194.00 mV

Testbedingungen erfüllt
Fehler momentan nicht vorhanden, aber bereits gespeichert
Fehler würde kein Aufleuchten einer Warnlampe verursachen
This is no event DTC. This ecu IS RESPONSIBLE for this error entry.

Error code: 00 01 A0 62 2C 01 17 00 01 48 10 17 01 09 7F F1
6A 40 00 00 95 17 51 40 01 00 95 17 56 40 02 00
8A 40 03 FF FF 40 04 0F 01 11 1F 40 05 00 13 40
06 00 00 30 F1 40 07 2F A2 01 00 02 01 03 FF
=============================================================




apiJob("ACSM4I","steuern","ARG;VERRIEGELUNG_SG;0","")

Satz : 0
OBJECT = acsm4i
SAETZE = 1
JOBNAME = steuern
VARIANTE = ACSM4I
JOBSTATUS =
UBATTCURRENT = -1
UBATTHISTORY = -1
IGNITIONCURRENT = -1
IGNITIONHISTORY = -1
Satz : 1
JOB_STATUS = ERROR_ECU_CONDITIONS_NOT_CORRECT
_REQUEST = 4 Bytes
0000 : 2E D4 82 00 .Ô?.
_RESPONSE = 3 Bytes
0000 : 7F 2E 22 ."