Please make sure you read Rules! and DO NOT upload/post any illegal softwares or Pirated Material , Thank you for understanding :)
  1. CarLabImmo

  2. AUTO-CHIPS

  3. Ecu-Service



Updated Orange5 Clone [Support/Feedback/Rework/Calculators]
04-07-2017, 19:13 PM, (This post was last modified: 16-05-2019, 01:44 AM by volavka.)
Post: #1
0Dash  Orange5 Clone [Support/Feedback/Rework/Calculators]
I have just bought orange 5 programmer and all seems to work well happy

I got fed up with my genuine upa usb s programmer which didnt seem to want to read anything, it went through the motions and said success reading a load of zeros gavel

Straight out of the box this Orange 5 clone read and write eproms 95640 and 95P08C3 in circuit no problem with no errors, but I had to make sure that my connections to the chip via test clip were all good and then tool work like charm nerd

I think I like it so far smile

has anyone else any experience good or bad with this programmer ?

very simple to use.


Attached Files
1.jpg
File Type: .jpg
Downloaded: 280 times
Size: 2.49 MB

3.jpg
File Type: .jpg
Downloaded: 236 times
Size: 6.41 MB

2.jpg
File Type: .jpg
Downloaded: 193 times
Size: 6.26 MB


Tight lines and bending rods are what makes my day biggrin

Dont PM asking me for files ! Post them in the forum where we can help.
Reputation: +3 - Rhogan [+1] , raffy haddad [+1] , CHIKODIAG [+1]
Quote this message in a reply
[+] 10 users say Thank You to ROD-BENDERS for this post
06-07-2017, 10:51 AM,
Post: #2
RE: Orange 5 clone feedback
I was thinking to buy one but didn't find much report about
So i bought the mprog and waiting to received it
And maybe later i buy o5 when members here post theyre report
Regards
Quote this message in a reply
[+] 1 user says Thank You to raffy haddad for this post
06-07-2017, 14:57 PM, (This post was last modified: 06-07-2017, 15:00 PM by mikroel.)
Post: #3
Orange 5 clone feedback
I have it for a long time and for now everything is working properly.
One of the few clones that works well and works as an original.

Some adapters are not supplied and must be purchased separately

Sent from my iPhone using Tapatalk
Reputation: +1 - ROD-BENDERS [+1]
Quote this message in a reply
[+] 3 users say Thank You to mikroel for this post
06-07-2017, 16:51 PM, (This post was last modified: 06-02-2018, 22:58 PM by volavka.)
Post: #4
RE: Orange 5 clone feedback
Sadly i don't have clone one to leave feedback
did you try with hc908 secured ?

hmmm adapters look craps, soldering by hand

No support in PM=Private Message anymore 
Post your Questions/Request in The Forum Section
Reputation: +2 - ROD-BENDERS [+1] , Diagnostix [+1]
Visit this user's website
Quote this message in a reply
[+] 3 users say Thank You to volavka for this post
06-07-2017, 18:47 PM, (This post was last modified: 06-07-2017, 18:47 PM by mikroel.)
Post: #5
RE: Orange 5 clone feedback
Adapters should be resolder for sure but it isn't so bad ,at all
The main point orange 5 clone isn't so bad as clones can be.
Good investment for sure . smile
Reputation: +1 - ROD-BENDERS [+1]
Quote this message in a reply
[+] 3 users say Thank You to mikroel for this post
06-07-2017, 19:20 PM,
Post: #6
RE: Orange 5 clone feedback
(06-07-2017, 18:47 PM)mikroel Wrote:  Adapters should be resolder for sure but it isn't so bad ,at all
The main point orange 5 clone isn't so bad as clones can be.
Good investment for sure . smile

So far its reading and writing (with verify) all eeproms i try. Good tool so far.

Volavka has sorted out my upa usb problem fail i need an adapter omg fail gaveladore

Tight lines and bending rods are what makes my day biggrin

Dont PM asking me for files ! Post them in the forum where we can help.
Reputation: +3 - volavka [+2] , Diagnostix [+1]
Quote this message in a reply
[+] 4 users say Thank You to ROD-BENDERS for this post
06-07-2017, 19:24 PM, (This post was last modified: 06-07-2017, 19:29 PM by mikroel.)
Post: #7
RE: Orange 5 clone feedback
(06-07-2017, 19:20 PM)ROD-BENDERS Wrote:  
(06-07-2017, 18:47 PM)mikroel Wrote:  Adapters should be resolder for sure but it isn't so bad ,at all
The main point orange 5 clone isn't so bad as clones can be.
Good investment for sure . smile

So far its reading and writing (with verify) all eeproms i try. Good tool so far.

Volavka has sorted out my upa usb problem fail i need an adapter omg fail gaveladore

I like PIN checking function (test insertions) very much .It saved my job a lot of time.smile
In combination with my UPA -S ,carprog ,and TL866 a lot of job can be done successfully .
Reputation: +3 - ROD-BENDERS [+1] , volavka [+2]
Quote this message in a reply
[+] 3 users say Thank You to mikroel for this post
06-07-2017, 19:40 PM, (This post was last modified: 07-07-2017, 17:51 PM by ROD-BENDERS.)
Post: #8
RE: Orange 5 clone feedback
My new xprog 5.70 arrived today with dongle, connect dongle connect usb BOOM yikes usb power surge error fail

I try on another laptop and same thing fxxxx clones devil

Update: Xprog 5.70 working like charm biggrin needed to download fresh software from seller all working without verify errors thumbsup

Tight lines and bending rods are what makes my day biggrin

Dont PM asking me for files ! Post them in the forum where we can help.
Quote this message in a reply
[+] 2 users say Thank You to ROD-BENDERS for this post
08-07-2017, 14:07 PM, (This post was last modified: 08-07-2017, 23:55 PM by rs@chip.)
Post: #9
RE: Orange 5 clone feedback
(06-07-2017, 19:40 PM)ROD-BENDERS Wrote:  My new xprog 5.70 arrived today with dongle, connect dongle connect usb BOOM yikes usb power surge error fail

I try on another laptop and same thing fxxxx clones devil

Update: Xprog 5.70 working like charm biggrin needed to download fresh software from seller all working without verify errors thumbsup

yes I have it 5.7 too and work perfect iven on win 10 x64..cas4-cas4+ and many more done no problem.. I also want to buy orange5 did you buy from same site as tm100 mate?
Quote this message in a reply
[+] 1 user says Thank You to rs@chip for this post
18-07-2017, 04:53 AM,
Post: #10
RE: Orange 5 clone feedback
Great programmer. All that is stated works. If the speed of exchange is not important, you can do a lot. Many good calculators
Quote this message in a reply
[+] 2 users say Thank You to kvihome for this post


Possibly Related Threads...
Thread Author Replies Views Last Post
0Dash MTool Mileage Correction suppot/Feedback thread volavka 51 22,024 19-05-2019, 16:00 PM
Last Post: Arvind
  Orange5 programmer-CLOSED mikroel 14 4,855 01-05-2019, 22:10 PM
Last Post: Sergiochaparro
0Dash Smok UHDS Support/Feedback/Backup Thread volavka 128 26,342 21-04-2019, 09:40 AM
Last Post: David89
0Dash X-tool suppot/Feedback/backup thread volavka 209 59,583 14-04-2019, 11:56 AM
Last Post: teerak2uk
0Dash MT401 experience feedback zgjana 47 9,069 29-03-2019, 04:27 AM
Last Post: paixfrawg
0Dash X-100 PRO Mileage Correction FeedBack ETPerformance 230 76,298 21-03-2019, 03:23 AM
Last Post: Yuki Shi
  R270 rework kermito 8 484 16-02-2019, 21:59 PM
Last Post: rightpcb
YTMercedes W211 mileage correction with carprog clone. Version 10.93 RUBBER_UNDIES 8 574 05-02-2019, 16:17 PM
Last Post: kryspl
0Dash IProg+ & IProgPro suppot/Feedback thread volavka 138 72,516 10-01-2019, 16:37 PM
Last Post: giangct
  Abrites 2014 clone isseus sandor1987 19 988 29-12-2018, 22:59 PM
Last Post: sandor1987

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content