Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

Solved ✔ Audi A4 1Z more power needed
05-03-2019, 07:13 AM, (This post was last modified: 18-03-2019, 07:25 AM by Cunder79.)
Post: #1
ZTAudi  Audi A4 1Z more power needed
Hi All! Audi A4 more power needed. 
1995, 90 HP, 028 906 021 F, 0281001366/367
Chip:2537355585+2537355586 (files from internet, the car comes only on weekends)
Orig chip can be replaced with AT27C512R-70PU or 45PU?
THX for the help!


Attached Files
audi_orig.rar
File Type: .rar
Downloaded: 11 times
Size: 39.72 KB

08-03-2019, 20:03 PM,
Post: #2
RE: Audi A4 1Z more power needed
(05-03-2019, 07:13 AM)Cunder79 Wrote:  Hi All! Audi A4 more power needed. 
1995, 90 HP, 028 906 021 F, 0281001366/367
Chip:2537355585+2537355586 (files from internet, the car comes only on weekends)
Orig chip can be replaced with AT27C512R-70PU or 45PU?
THX for the help!

Your files  under  (pass is in PM)

For the best results on this engine first you have to check and adjust:

-INJECTION TIMING 
http://www.ross-tech.com/vag-scope/TDIGraph.html
But your pump differs from this on the video. Yours is an older version. It has 3 screws through the pulley and one on the back. First, lose 3 screws through the pulley lightly. Than let the engine run to the 80 deg. Lose 4 screw and push the pump in the direction of the cockpit, to get the early injection. Watch te screen and set it in the upper third point. Tight the screw when you reach the point you need. 
Turn off engine. Tighten the other screws, through the holes in the pulley !!!

-INJECTION QUANTITY 
VCDS measuring blocks/group 1/field 2
Set it cca 3,5 mgr/str (I can not explain it now, but: do not push to higher values because it will not get better, but opposite.)
Do this by slightly loosening the screws and gently pushing the upper part of the pump in the direction of the pump shaft. It's about a fraction of a millimeter. The engine must be hot. Watch the amount of fuel on the monitor all the time.


Attached Files
d-tun.rar
File Type: .rar
Downloaded: 6 times
Size: 39.8 KB

Reputation: +1 - Cunder79 [+1]
[+] 1 user says Thank You to D1971 for this post
09-03-2019, 20:53 PM,
Post: #3
RE: Audi A4 1Z more power needed
(08-03-2019, 20:03 PM)D1971 Wrote:  
(05-03-2019, 07:13 AM)Cunder79 Wrote:  Hi All! Audi A4 more power needed. 
1995, 90 HP, 028 906 021 F, 0281001366/367
Chip:2537355585+2537355586 (files from internet, the car comes only on weekends)
Orig chip can be replaced with AT27C512R-70PU or 45PU?
THX for the help!

Your files  under  (pass is in PM)

For the best results on this engine first you have to check and adjust:

-INJECTION TIMING 
http://www.ross-tech.com/vag-scope/TDIGraph.html
But your pump differs from this on the video. Yours is an older version. It has 3 screws through the pulley and one on the back. First, lose 3 screws through the pulley lightly. Than let the engine run to the 80 deg. Lose 4 screw and push the pump in the direction of the cockpit, to get the early injection. Watch te screen and set it in the upper third point. Tight the screw when you reach the point you need. 
Turn off engine. Tighten the other screws, through the holes in the pulley !!!

-INJECTION QUANTITY 
VCDS measuring blocks/group 1/field 2
Set it cca 3,5 mgr/str (I can not explain it now, but: do not push to higher values because it will not get better, but opposite.)
Do this by slightly loosening the screws and gently pushing the upper part of the pump in the direction of the pump shaft. It's about a fraction of a millimeter. The engine must be hot. Watch the amount of fuel on the monitor all the time.
You can adjust Injection timing and quantity by vcds cabble if need help pm
[+] 1 user says Thank You to Leaking for this post
10-03-2019, 07:44 AM, (This post was last modified: 10-03-2019, 07:57 AM by D1971.)
Post: #4
RE: Audi A4 1Z more power needed
(09-03-2019, 20:53 PM)Leaking Wrote:  
(08-03-2019, 20:03 PM)D1971 Wrote:  
(05-03-2019, 07:13 AM)Cunder79 Wrote:  Hi All! Audi A4 more power needed. 
1995, 90 HP, 028 906 021 F, 0281001366/367
Chip:2537355585+2537355586 (files from internet, the car comes only on weekends)
Orig chip can be replaced with AT27C512R-70PU or 45PU?
THX for the help!

Your files  under  (pass is in PM)

For the best results on this engine first you have to check and adjust:

-INJECTION TIMING 
http://www.ross-tech.com/vag-scope/TDIGraph.html
But your pump differs from this on the video. Yours is an older version. It has 3 screws through the pulley and one on the back. First, lose 3 screws through the pulley lightly. Than let the engine run to the 80 deg. Lose 4 screw and push the pump in the direction of the cockpit, to get the early injection. Watch te screen and set it in the upper third point. Tight the screw when you reach the point you need. 
Turn off engine. Tighten the other screws, through the holes in the pulley !!!

-INJECTION QUANTITY 
VCDS measuring blocks/group 1/field 2
Set it cca 3,5 mgr/str (I can not explain it now, but: do not push to higher values because it will not get better, but opposite.)
Do this by slightly loosening the screws and gently pushing the upper part of the pump in the direction of the pump shaft. It's about a fraction of a millimeter. The engine must be hot. Watch the amount of fuel on the monitor all the time.
You can adjust Injection timing and quantity by vcds cabble if need help pm

Of course it can. 
This is an old car and this is probably no longer interesting to anybody, but I've fixed a lot of these pumps.
You young people are looking for quick fixes.
Sometimes the regulator can not reach the soft set and the pump must be moved physically.
So, this instruction above is for the pure old school and leave 32768 untouched.
Old man-old school.
18-03-2019, 07:23 AM,
Post: #5
RE: Audi A4 1Z more power needed
(08-03-2019, 20:03 PM)D1971 Wrote:  
(05-03-2019, 07:13 AM)Cunder79 Wrote:  Hi All! Audi A4 more power needed. 
1995, 90 HP, 028 906 021 F, 0281001366/367
Chip:2537355585+2537355586 (files from internet, the car comes only on weekends)
Orig chip can be replaced with AT27C512R-70PU or 45PU?
THX for the help!

Your files  under  (pass is in PM)

For the best results on this engine first you have to check and adjust:

-INJECTION TIMING 
http://www.ross-tech.com/vag-scope/TDIGraph.html
But your pump differs from this on the video. Yours is an older version. It has 3 screws through the pulley and one on the back. First, lose 3 screws through the pulley lightly. Than let the engine run to the 80 deg. Lose 4 screw and push the pump in the direction of the cockpit, to get the early injection. Watch te screen and set it in the upper third point. Tight the screw when you reach the point you need. 
Turn off engine. Tighten the other screws, through the holes in the pulley !!!

-INJECTION QUANTITY 
VCDS measuring blocks/group 1/field 2
Set it cca 3,5 mgr/str (I can not explain it now, but: do not push to higher values because it will not get better, but opposite.)
Do this by slightly loosening the screws and gently pushing the upper part of the pump in the direction of the pump shaft. It's about a fraction of a millimeter. The engine must be hot. Watch the amount of fuel on the monitor all the time.

Perfect job! THX!


Possibly Related Threads…
Thread Author Replies Views Last Post
  Audi a4 b7 2.0 tfsi rail pressure change me9.1.5 yaroliban 0 8 5 hours ago
Last Post: yaroliban
ZTAudi audi 4.2 tdi edc17cp44 stage 1 aladinnu 1 19 Yesterday, 12:50 PM
Last Post: aladinnu
  Audi A4 2002 2.0FSI swirl flaps and O2 sensor off need Mate 0 25 27-03-2024, 21:39 PM
Last Post: Mate
ZTAudi audi a5 CCWA original please DavidT 1 14 27-03-2024, 20:55 PM
Last Post: lsdlsd88
  Need ori AUDI A6 C6 2.7TDI EDC16CP34 Leaking 2 24 27-03-2024, 19:36 PM
Last Post: Leaking
  Audi A4 B7 - 2.0 TDI - 170 HP - Stage 1 Mooti 0 36 26-03-2024, 18:15 PM
Last Post: Mooti
  Audi A6 MD1CP004 Adblue AtomT 2 96 25-03-2024, 09:40 AM
Last Post: foxportal
  F10 518D 143HP - ori needed for learning Purposes. claudiuvisan90 2 76 24-03-2024, 17:52 PM
Last Post: claudiuvisan90
ZVW EGR and DPF delete needed zijad77 3 72 24-03-2024, 10:50 AM
Last Post: eurofix
LFord Ford C-Max 2008 help needed mini1.3 1 55 23-03-2024, 01:12 AM
Last Post: kreepyme

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content