Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Help with reading EDC17C10 TPROT12 ECU
|
25-03-2019, 18:47 PM,
Post: #1
|
|||
|
|||
|
Help with reading EDC17C10 TPROT12 ECU
Hi,
I have Ford Aspire 2015 Diesel car. Trying to read ECU via OBD with Kess v2 EU Clone. Software suite 2.47 Here is what I am getting while reading ECU. "Wrong Security Code". I have attached screenshots. Also, tried to read using "protocols" option and it says "MEDC17 interface not present" error. Do I have to open ECU to read it? I am newbie learning about tuning. Any help is appreciated. |
|||
|
![[+]](https://cartechnology.co.uk/images/CarTechnologyTheCure/collapse_collapsed.png)
|
25-03-2019, 22:34 PM,
Post: #2
|
|||
|
|||
|
RE: Help with reading EDC17C10 TPROT12 ECU
Hello,
at Ford, I do not know that way, but at Audi and VW is that with TPROT12 only about KTAG and the GPT cable goes and of course open the case. But I'm not sure. Have a look at the KTAG. I wish you success Greeting bit |
|||
|
|
|
25-03-2019, 23:36 PM,
Post: #3
|
|||
|
|||
|
RE: Help with reading EDC17C10 TPROT12 ECU
Hi,
Maybe 11.88 volts is not enough for this reading. Connect the charger - provide at least 12.5 |
|||
|
|
|
26-03-2019, 06:27 AM,
Post: #4
|
|||
|
|||
RE: Help with reading EDC17C10 TPROT12 ECU
(25-03-2019, 22:34 PM)bit1976 Wrote: Hello,Thanks for Your reply. I don't have Ktag and before I return this Kess V2 I want to try if it works with my car ( If it doesn't then I m going to return it ). (25-03-2019, 23:36 PM)yudon Wrote: Hi, Voltage fluctuates between 11.8 to 12.5v. I will try plugging charger to battery points and see if it works. -------------- Meanwhile, I downloaded help files for Kess v2 and got instructions for Ford EDC17C10 bootloader Tricore reading method as attached in screenshots below. It isn't mentioned about TPROT though. Also, I have all additional cable came with Kess V2 and as required in reading as shown below. I thought only Ktag works with opened ECU. Is following method correct? I have skipped connection method to "Direct Connection" here in screenshots. |
|||
|
|
|
26-03-2019, 14:10 PM,
Post: #5
|
|||
|
|||
|
RE: Help with reading EDC17C10 TPROT12 ECU
Update : Just re-tried with battery charger connected. Still same results
 .
|
|||
|
|
|
27-03-2019, 04:12 AM,
Post: #6
|
|||
|
|||
|
RE: Help with reading EDC17C10 TPROT12 ECU
No one to help?
|
|||
|
|
|
27-03-2019, 05:39 AM,
Post: #7
|
|||
|
|||
|
RE: Help with reading EDC17C10 TPROT12 ECU
Tricore processor, you need open ecu & read with tricore module attached to kess v2.
Br, |
|||
|
|
|
27-03-2019, 18:02 PM,
(This post was last modified: 27-03-2019, 18:42 PM by amit_talkin.)
Post: #8
|
|||
|
|||
|
RE: Help with reading EDC17C10 TPROT12 ECU
Okey i managed to open ECU and tried to read it in boot mode. Now Kess gives me following error.
"MICRO wakeup error". Any clue on this? |
|||
|
|
|
28-03-2019, 05:27 AM,
(This post was last modified: 28-03-2019, 10:34 AM by amit_talkin.)
Post: #9
|
|||
|
|||
|
RE: Help with reading EDC17C10 TPROT12 ECU
Update: I tried to run tool on Windows XP, now it shows me "MICRO unprotection failed" error.
|
|||
|
|
|
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content
