Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

Help F10 2015 High Beam Assist Retrofit (Xenon Only)
12-06-2019, 09:11 AM,
Post: #21
RE: Help F10 2015 High Beam Assist Retrofit (Xenon Only)
(12-06-2019, 00:45 AM)dncomputech Wrote:  
(11-06-2019, 14:39 PM)Gizmo520d Wrote:  That's strange. Is any error stored?
You can try to flash the szl

I have no errors in Isata +.
The HBA button also works well (on / off) after VO code or Edit FDL ECU FRM (only Edit FDL Code FRM face even if there is no change in FRM).
But the HBA button does not work when the engine starts next time
I think that in the ECU FRM command there is something that switches HBA or does not wake the HBA.

first of all if the  FLA and  SZL is used then you need to to flash it with esys , then you need to code the whole car after adding 5AC to the FA , I don't understand why you keep FDL coding some ecu's while many other ECU's are also involved in this job .. the mirror is connected on CAN2 so any other ECU's on the same network must be coded , not only KOMBI and FRM .

without flashing to update the VIN , and without proper coding nothing will work . you want this to work right then you need to do it right too . forget about some codes and values to be edited because that's Esys job to ensure all ECU's are coded correctly .. 
Quote this message in a reply
[+] 1 user says Thank You to emhtuning for this post
12-06-2019, 14:01 PM, (This post was last modified: 12-06-2019, 16:01 PM by dncomputech.)
Post: #22
RE: Help F10 2015 High Beam Assist Retrofit (Xenon Only)
(12-06-2019, 09:11 AM)emhtuning Wrote:  
(12-06-2019, 00:45 AM)dncomputech Wrote:  
(11-06-2019, 14:39 PM)Gizmo520d Wrote:  That's strange. Is any error stored?
You can try to flash the szl

I have no errors in Isata +.
The HBA button also works well (on / off) after VO code or Edit FDL ECU FRM (only Edit FDL Code FRM face even if there is no change in FRM).
But the HBA button does not work when the engine starts next time
I think that in the ECU FRM command there is something that switches HBA or does not wake the HBA.

first of all if the  FLA and  SZL is used then you need to to flash it with esys , then you need to code the whole car after adding 5AC to the FA , I don't understand why you keep FDL coding some ecu's while many other ECU's are also involved in this job .. the mirror is connected on CAN2 so any other ECU's on the same network must be coded , not only KOMBI and FRM .

without flashing to update the VIN , and without proper coding nothing will work . you want this to work right then you need to do it right too . forget about some codes and values to be edited because that's Esys job to ensure all ECU's are coded correctly .. 


I recorded the work that did not succeed for HBA
1./Install the mirror with ECU FLA (connect 2 K-Can2 wires) into the K-Can2 JBBF common because my car does not have K-Can2 on the roof.
2. / Change FA (FA5AC) add 5AC without Save and vehicle, click FA5AC when programming.
3. / Detect CAF SWE for ECU FLA3 and VO Code FLA3, FRM, KOMBI, JBBF, ICM, DSC2.
4./Edit FDL FRM (FLA_AUTO_AKTIV = automatisch).
5./Logo HBA appears on KOMBI when switching off the Auto-Off-Auto light (Currently not changing the SZL Cluster with HBA button).
6. / Test car on dark roads, HBA works great.
7./The car engine and I turned on the car again the HBA did not work even though I switched the Auto-Off-Auto light switch.
8./Return E-sys check FRM FLA_AUTO_AKTIV = automatisch is normal, I do not change anything FRM and select Code FDL FRM. At this time the HBA works again when switching the Auto-Off-Auto switch. But the switch to open the car again HBA does not work even if I switch the Auto-Off-Auto light switch.
9./I think the F10 LCI 2016 BMW function HBA auto switch, which must have the HBA button on the SZL Cluster.
10./ I replaced another SZL cluster with HBA button.
11./ Enable FA5AC, Detect CAF SWE for ECU SZL_LWS, select the latest >>> Code
12./ It all works exactly what the SZL Cluster has an HBA button
Press the HBA button = On / Off, but switch the car and open the car again, the HBA button has no effect.
13./ Checking FRM and FLA3 VO Code FRM, FLA3 with FA5AC, the HBA button works. But the switch back to the HBA does not work even if I switch the Auto-Off-Auto light switch and press the HBA button on SZL with no effect.
14./ I have tried Code FDL FRM (without changing any parameters in ECU FRM), the HBA button works. But the switch back to the HBA does not work even if I switch the Auto-Off-Auto light switch and press the HBA button on SZL with no effect. thinking
Currently I run out of ideas for Retrofit HBA   fail
I have attached FA5AC File


Attached Files Thumbnail(s)
   
10-5-19(5AC)xml.rar
File Type: .rar
Downloaded: 3 times
Size: 588 bytes

Quote this message in a reply
12-06-2019, 15:30 PM,
Post: #23
RE: Help F10 2015 High Beam Assist Retrofit (Xenon Only)
Can you send your SVT file?

under Press  and  if this post helped you.
Quote this message in a reply
12-06-2019, 15:54 PM,
Post: #24
RE: Help F10 2015 High Beam Assist Retrofit (Xenon Only)
(12-06-2019, 15:30 PM)Gizmo520d Wrote:  Can you send your SVT file?

SVT  và CAF FRM, FLA3


Attached Files
STV5AC(10-5-19).rar
File Type: .rar
Downloaded: 6 times
Size: 2.42 KB

FRM-FLA3.rar
File Type: .rar
Downloaded: 1 times
Size: 1.93 KB

Quote this message in a reply
12-06-2019, 20:52 PM,
Post: #25
RE: Help F10 2015 High Beam Assist Retrofit (Xenon Only)
These should be the lines that are changed after VO coding. Especially check the FRM.

<<< CAFD_00000014.caf.004_100_010 (JBBFE) >>>
JBBFE > FZM_EnergyDataMemory_FeTra_LIN 3200 > LIN_VARIANTE_INNENSPIEGEL = nicht_aktiv [Default]

<<< CAFD_00000C18.caf.014_082_006 (DSC_Premium) >>>
DSC_Premium > Applikationsparameter 3009 > CCC_CoMPerm = wert_00
DSC_Premium > Applikationsparameter 3009 > CCC_CoMPermDTC = wert_00
DSC_Premium > Applikationsparameter 3009 > CCC_CoPCCC = wert_00
DSC_Premium > Applikationsparameter 3009 > CCC_fLwDyn = wert_00
DSC_Premium > Applikationsparameter 3009 > CCC_MLCay = wert_00
DSC_Premium > Teillisten 3007 > Teilliste_CCC = wert_00

<<< CAFD_0000106D.caf.015_007_010 (FRM__03CT) >>>
FRM__03CT > FRM_AUSSENLICHT_PARAMETER 3050 > FLA_VERBAUT = aktiv
FRM__03CT > LaMaster1 3073 > C_HBA_ENA = F010_disable
FRM__03CT > LaMaster2 3074 > C_HBA_CAM_POS_Z = F010_KafasLow

<<< CAFD_00000069.caf.010_001_210 (KOMBI L6 BO) >>>
KOMBI L6 BO > ERM_Konfiguration 3004 > ST_MAB_ASST_APPL = aktiv
KOMBI L6 BO > ERM_Konfiguration 3004 > ST_MAB_ASST_TIMEOUT = aktiv

under Press  and  if this post helped you.
Quote this message in a reply
13-06-2019, 02:38 AM, (This post was last modified: 13-06-2019, 02:49 AM by dncomputech.)
Post: #26
RE: Help F10 2015 High Beam Assist Retrofit (Xenon Only)
(12-06-2019, 20:52 PM)Gizmo520d Wrote:  These should be the lines that are changed after VO coding. Especially check the FRM.

<<< CAFD_00000014.caf.004_100_010  (JBBFE) >>>
JBBFE > FZM_EnergyDataMemory_FeTra_LIN 3200 > LIN_VARIANTE_INNENSPIEGEL = nicht_aktiv [Default]

<<< CAFD_00000C18.caf.014_082_006  (DSC_Premium) >>>
DSC_Premium > Applikationsparameter 3009 > CCC_CoMPerm = wert_00
DSC_Premium > Applikationsparameter 3009 > CCC_CoMPermDTC = wert_00
DSC_Premium > Applikationsparameter 3009 > CCC_CoPCCC = wert_00
DSC_Premium > Applikationsparameter 3009 > CCC_fLwDyn = wert_00
DSC_Premium > Applikationsparameter 3009 > CCC_MLCay = wert_00
DSC_Premium > Teillisten 3007 > Teilliste_CCC = wert_00

<<< CAFD_0000106D.caf.015_007_010  (FRM__03CT) >>>
FRM__03CT > FRM_AUSSENLICHT_PARAMETER 3050 > FLA_VERBAUT = aktiv
FRM__03CT > LaMaster1 3073 > C_HBA_ENA = F010_disable
FRM__03CT > LaMaster2 3074 > C_HBA_CAM_POS_Z = F010_KafasLow

<<< CAFD_00000069.caf.010_001_210  (KOMBI L6 BO) >>>
KOMBI L6 BO > ERM_Konfiguration 3004 > ST_MAB_ASST_APPL = aktiv
KOMBI L6 BO > ERM_Konfiguration 3004 > ST_MAB_ASST_TIMEOUT = aktiv



Thank you for your help
Previously I did the method to compare CAF with NcdCafdTool by TokenMaster's tool like what you said, but failed.
Should I change the VO Code method to ECU FRM, DSC2, KOMBI, FLA, JBBF, ICM, SZL like what "emhtuning" says
After Vo code, I have checked the file then it's like what NcdCafdTool authored TokenMaster compare, and I Edit 
But I'm still not lucky.
When I sent STV.xml I discovered that in the STV.xml content there are many abnormalities unlike STV.xml in 2018 I saved (Not Retrofit 5AC).
STV.xml I sent you there is an abnormality but Ista + does not report any errors.


Attached Files Thumbnail(s)
           
Quote this message in a reply
14-06-2019, 02:25 AM, (This post was last modified: 14-06-2019, 07:22 AM by dncomputech.)
Post: #27
RE: Help F10 2015 High Beam Assist Retrofit (Xenon Only)
Hi everybody
I have a question about E-sys a little, maybe because I'm not fluent.
1. / Open E-sys >> select the type of vehicle connection >>> Select VIN >>>> connection Open Expert Mode window >>>> Coding >>> Read FA >> read (VCM) >>> click must 01 ECU >>> Code
2. / Open E-sys >> select the type of car connection >>> Select VIN >>>> connection Open Expert Mode window >>>> Coding >>> Read FA >> read (ECU) >>> click must 01 ECU >>> Code
3. / Open E-sys >> select the connection type >>> Select VIN >>>> connection Open Expert Mode window >>>> Coding >>> Read FA >> Load (saved last time)> >> right click 01 ECU >>> Code.
Are all three steps 1-2-3 different? or the same is 1
I asked because I felt different here
a/ Open E-sys >> select the connection type >>> Select VIN >>>> connection Open Expert Mode window >>>> Coding >>> Read FA >> read (VCM) >>> Save
b / Open E-sys >> select the type of vehicle connection >>> Select connection VIN >>>> Open Expert Mode window >>>> Coding >>> Read FA >> read (ECU) >>> Save
Step a-b gives 2 different save results
Quote this message in a reply
14-06-2019, 05:55 AM, (This post was last modified: 14-06-2019, 05:57 AM by Gizmo520d.)
Post: #28
RE: Help F10 2015 High Beam Assist Retrofit (Xenon Only)
It is correct that these might give different readings.

For question regarding A/B
If you retrofit an ECU it will not show up when you press "Read VCM" because the car doens't have that ECU in it's VCM list.
When you press "Read ECU" you will poll each possible ECU and the ones that are responding will show up.

For question regarding 1/2/3
These might also give different outcomes. Depending on the same variables as stated here before.
Loading the SVT might even differ more, depending on when it was save and if it is the SVT from the car.

under Press  and  if this post helped you.
Quote this message in a reply
14-06-2019, 07:29 AM, (This post was last modified: 14-06-2019, 07:50 AM by dncomputech.)
Post: #29
RE: Help F10 2015 High Beam Assist Retrofit (Xenon Only)
I recall.
My car does not have 2VB and 5AC, I add 2VB, 5AC to FA
I enabled FA to have 2VB, 5AC unsaved FA to car >>> read (VCM) I saw ECU RDC, FLA3 on me done Detecting CAF SWE Then Code
On the other hand when I saved STV.xlm on request Gizmo520d I discovered that reading VCM and reading ECU and then saving it for 2 different results.
Quote this message in a reply
14-06-2019, 08:06 AM, (This post was last modified: 14-06-2019, 08:07 AM by emhtuning.)
Post: #30
RE: Help F10 2015 High Beam Assist Retrofit (Xenon Only)
(14-06-2019, 07:29 AM)dncomputech Wrote:  I recall.
My car does not have 2VB and 5AC, I add 2VB, 5AC to FA
I enabled FA to have 2VB, 5AC unsaved FA to car >>> read (VCM) I saw ECU RDC, FLA3 on me done Detecting CAF SWE Then Code
On the other hand when I saved STV.xlm on request Gizmo520d I discovered that reading VCM and reading ECU and then saving it for 2 different results.

again you are doing all wrong , I guess you need to pay someone to do proper flashing and coding for you or spend sometime learning Esys , why you keep using detect CAFD ,  hiddentmi

and why are you not saving the updated FA to the car , this retrofit is permanent so you need to update your FA in the car too .
Quote this message in a reply
[+] 1 user says Thank You to emhtuning for this post


Possibly Related Threads…
Thread Author Replies Views Last Post
  Car Systems / Custom Retrofit Garage ENBT Adapter Ulsmak 33 1,410 Yesterday, 00:17 AM
Last Post: painsage
  G30 LCI Headlights retrofit: High Beam Laser light locking active tcp443 19 3,194 26-03-2024, 21:25 PM
Last Post: Satia
  G05 KAFAS4 enable code missing after Retrofit ACC 6ergsm 19 2,275 26-03-2024, 12:33 PM
Last Post: Hodgsonp
  F15 6WB Retrofit VIN Error moreply 4 172 25-03-2024, 07:24 AM
Last Post: RuleNormaliai
XZBMW 2015 F82 M4 NBT_EVO repetition of loading Bimmerwerks 4 279 25-03-2024, 04:11 AM
Last Post: Bimmerwerks
  E60 pre LCI, wiring in adaptive xenon to xenon loom GoNz0- 5 121 24-03-2024, 23:27 PM
Last Post: NeRkO20
  MGU G30 retrofit , PDC does not show laso 3 167 24-03-2024, 14:35 PM
Last Post: laso
  Problem Retrofit electrified steering column on the G31 LCI smercki 12 318 22-03-2024, 12:55 PM
Last Post: Node
XZBMW BMW F01 Pre-LCI NBT EVO Retrofit Satia 3 211 21-03-2024, 12:53 PM
Last Post: Satia
  Bmw G31 retrofit Mgu id7 atm problem intranet 14 1,873 19-03-2024, 10:07 AM
Last Post: evaldazj

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content