[Maxwarmer]

I have a F82 car with Enet cable, then I connect Ista+ last version to my car, rear car and make a general tester, after it I clean all module faults, then all convert to green, after it, I want to make software update, then I will go to vehicle manager and after it I will pust to software update, but I can not push it because button are disabled, any body knows because this are disabled? I want to update my software car with my enet cable and ista+.

We need any aditional file or folder installed? Why this button are disabled? I check other photos from ista+ and this button are enable and can make the software update.




https://esauc-my.sharepoint.com/:i:/g/pe...g?e=eAQNai



https://esauc-my.sharepoint.com/:i:/g/pe...g?e=o2ksHp

Thanks for your comments.

[noobontour]

I have a F82 car with Enet cable, then I connect Ista+ last version to my car, rear car and make a general tester, after it I clean all module faults, then all convert to green, after it, I want to make software update, then I will go to vehicle manager and after it I will pust to software update, but I can not push it because button are disabled, any body knows because this are disabled? I want to update my software car with my enet cable and ista+.

We need any aditional file or folder installed? Why this button are disabled? I check other photos from ista+ and this button are enable and can make the software update.




https://esauc-my.sharepoint.com/:i:/g/pe...g?e=eAQNai



https://esauc-my.sharepoint.com/:i:/g/pe...g?e=o2ksHp

Thanks for your comments.

Have you downloaded the Full SDP Data and placed them into the correct folder ?

[jogi8850]

Hey,
which version are you used? from Sedoy?

* to programming with ENET replace RheingoldProgramming.dll with RheingoldProgramming.dll.patched_for_ENET_programming (At your own risk.)

If I help you, please push thanks and reputation.

Regards Jürgen

[Maxwarmer]

I have a F82 car with Enet cable, then I connect Ista+ last version to my car, rear car and make a general tester, after it I clean all module faults, then all convert to green, after it, I want to make software update, then I will go to vehicle manager and after it I will pust to software update, but I can not push it because button are disabled, any body knows because this are disabled? I want to update my software car with my enet cable and ista+.

We need any aditional file or folder installed? Why this button are disabled? I check other photos from ista+ and this button are enable and can make the software update.




https://esauc-my.sharepoint.com/:i:/g/pe...g?e=eAQNai



https://esauc-my.sharepoint.com/:i:/g/pe...g?e=o2ksHp

Thanks for your comments.

Have you downloaded the Full SDP Data and placed them into the correct folder ?

No, don't make it, because Full SDP Data is only for Icom, and I have a Enet cable, then I don't need this files

[BusyBox]

Full SDP is required for PROGRAMMING with no matter what interface...

[Node]

Most of full Data is the firmware which is flashed to the car. Its not related to ICOM in any way. But as ISTA+ natively does not support flashing over enet - use jogi8850's suggestion AT YOUR OWN RISK. But you still need Full SDP, else you don't have anything to flash to the car...

P.S. Do you even have power supply for a car while its flashed?

[Maxwarmer]

Most of full Data is the firmware which is flashed to the car. Its not related to ICOM in any way. But as ISTA+ natively does not support flashing over enet - use jogi8850's suggestion AT YOUR OWN RISK. But you still need Full SDP, else you don't have anything to flash to the car...

P.S. Do you even have power supply for a car while its flashed?

Yes, I have power supply, 60A, no problm for it.

Then if ISTA+ does not support flashing over enet, what is the native program for make it, is Ista-P??

Can you tell me which version is last SDP files for flash it? is this SDP 4.16.10.7?

Thanks a lot

[jaramillo]

Why you want to flash your car?
Start reading about esys first

[Maxwarmer]

Hi think last SDP Data is the same that my ISTA+ 4.17.23, I will search for get it

---

Why you want to flash your car?
Start reading about esys first

Yes, I want flash car. I read about esys, but I think that is more easy and grafical make it from Ista+, right? I use esys for code it, and ista+ for diagnose, then now I will try ista+ for flash it.

Is better use esys than ista+ for flash it? Is esys native program for flash it?

Thanks

[noobontour]

Hi think last SDP Data is the same that my ISTA+ 4.17.23, I will search for get it

---

Why you want to flash your car?
Start reading about esys first

Yes, I want flash car. I read about esys, but I think that is more easy and grafical make it from Ista+, right? I use esys for code it, and ista+ for diagnose, then now I will try ista+ for flash it.

Is better use esys than ista+ for flash it? Is esys native program for flash it?

Thanks

For example with ISTA+ you can only flash ALL ecu (but only those for which there is an update present will get it). With e-sys you are more "free" in flashing.