Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

ICAM will not code on the Bench
28-06-2019, 00:43 AM,
Post: #1
ICAM will not code on the Bench
I don't know what I am doing wrong. I am trying to change the VIN on a used ICAM camera so I can use it in a enbt setup. I have it hooked up to a ZGW out of a 2017 X3 and it will not load up in e-sys. Does anyone have any ideas? If anyone in the US can change the VIN of the ICAM I will ship it to you and pay you. I have spent days on this.
Quote this message in a reply
28-06-2019, 08:07 AM,
Post: #2
RE: ICAM will not code on the Bench
post the ICAM part number if you have it , and if I remember correctly , ICAM runs on CAN3 same as LED adaptive headlights ,
Quote this message in a reply
28-06-2019, 10:02 AM,
Post: #3
RE: ICAM will not code on the Bench
i use icam high 360 module in enbt without fail.
i not change vin and work.

for moment i only put rear camera. 360 vision are crap (i have same system in my X4...)
panormic front and rear view are excelent.
but problem is ENBT/almost E9X not have camera buttom, so not is possible activate panoramic view.
only is possible 360 view and rear view...

i will try contact with carsystem developers, im sure is possible asign camera buttom to other exist buttom with custom firmware in ENBT, but only for few users, sure developers not making custom firmware...

Please, Press the Buttons [Image: postbit_thx.gif] and [Image: postbit_reputation.gif] if This post help or is usefull for you! Not is needed write just only thanks in Threads thumbsup
Quote this message in a reply
28-06-2019, 19:21 PM, (This post was last modified: 28-06-2019, 19:26 PM by Mizta Insane.)
Post: #4
RE: ICAM will not code on the Bench
(28-06-2019, 08:07 AM)emhtuning Wrote:  post the ICAM part number if you have it  , and if I remember correctly , ICAM runs on CAN3 same as LED adaptive headlights ,

(28-06-2019, 10:02 AM)ruben_17non Wrote:  i use icam high 360 module in enbt without fail.
i not change vin and work.

for moment i only put rear camera. 360 vision are crap (i have same system in my X4...)
panormic front and rear view are excelent.
but problem is ENBT/almost E9X not have camera buttom, so not is possible activate panoramic view.
only is possible 360 view and rear view...

i will try contact with carsystem developers, im sure is possible asign camera buttom to other exist buttom with custom firmware in ENBT, but only for few users, sure developers not making custom firmware...

Can you send pictures of your front and rear camera setup?

I buy these cameras from my carsystems dealer. He normally codes the cameras with the atm donor vin but this one he said the vin had an error. The camera will work once and then stop working. He said to hook the camera up to k can2 on the bench.


Attached Files Thumbnail(s)
       
Quote this message in a reply
28-06-2019, 21:36 PM,
Post: #5
RE: ICAM will not code on the Bench
(28-06-2019, 19:21 PM)Mizta Insane Wrote:  
(28-06-2019, 08:07 AM)emhtuning Wrote:  post the ICAM part number if you have it  , and if I remember correctly , ICAM runs on CAN3 same as LED adaptive headlights ,

(28-06-2019, 10:02 AM)ruben_17non Wrote:  i use icam high 360 module in enbt without fail.
i not change vin and work.

for moment i only put rear camera. 360 vision are crap (i have same system in my X4...)
panormic front and rear view are excelent.
but problem is ENBT/almost E9X not have camera buttom, so not is possible activate panoramic view.
only is possible 360 view and rear view...

i will try contact with carsystem developers, im sure is possible asign camera buttom to other exist buttom with custom firmware in ENBT, but only for few users, sure developers not making custom firmware...

Can you send pictures of your front and rear camera setup?

I buy these cameras from my carsystems dealer. He normally codes the cameras with the atm donor vin but this one he said the vin had an error. The camera will work once and then stop working. He said to hook the camera up to k can2 on the bench.

rear camera i use G30 trim camera with switch. is more big than original trim, is need drill metal lid.
for front camera, for moment i not mount.
but i buy pair of different trims. i not sure if drill just hole in bumper or in grille


but you have camera for icam module, or just is camera icam RVC?

Please, Press the Buttons [Image: postbit_thx.gif] and [Image: postbit_reputation.gif] if This post help or is usefull for you! Not is needed write just only thanks in Threads thumbsup
Quote this message in a reply
28-06-2019, 21:39 PM, (This post was last modified: 28-06-2019, 21:40 PM by Mizta Insane.)
Post: #6
RE: ICAM will not code on the Bench
(28-06-2019, 21:36 PM)ruben_17non Wrote:  
(28-06-2019, 19:21 PM)Mizta Insane Wrote:  
(28-06-2019, 08:07 AM)emhtuning Wrote:  post the ICAM part number if you have it  , and if I remember correctly , ICAM runs on CAN3 same as LED adaptive headlights ,

(28-06-2019, 10:02 AM)ruben_17non Wrote:  i use icam high 360 module in enbt without fail.
i not change vin and work.

for moment i only put rear camera. 360 vision are crap (i have same system in my X4...)
panormic front and rear view are excelent.
but problem is ENBT/almost E9X not have camera buttom, so not is possible activate panoramic view.
only is possible 360 view and rear view...

i will try contact with carsystem developers, im sure is possible asign camera buttom to other exist buttom with custom firmware in ENBT, but only for few users, sure developers not making custom firmware...

Can you send pictures of your front and rear camera setup?

I buy these cameras from my carsystems dealer. He normally codes the cameras with the atm donor vin but this one he said the vin had an error. The camera will work once and then stop working. He said to hook the camera up to k can2 on the bench.

rear camera i use G30 trim camera with switch. is more big than original trim, is need drill metal lid.
for front camera, for moment i not mount.
but i buy pair of different trims. i not sure if drill just hole in bumper or in grille


but you have camera for icam module, or just is camera icam RVC?

I only have the icam rvc center cut into my e90 trunk.
Quote this message in a reply
29-06-2019, 03:29 AM,
Post: #7
RE: ICAM will not code on the Bench
Do I need a terminating resistor?
Quote this message in a reply
29-06-2019, 11:20 AM,
Post: #8
RE: ICAM will not code on the Bench
(29-06-2019, 03:29 AM)Mizta Insane Wrote:  Do I need a terminating resistor?

yes, i never mount icam rvc but im sure 99,9%, terminating resistor is need. buy is cheap.

i first step i mean in retrofit icam rvc. but only one camera is possible mount. and i want front and rear camera. by this i decide mount icam high module.

[Image: attachment.php?attachmentid=1692643&stc=...04241http:]

Number 3 is for camera icam high 360
Number 4 is for camera icam RVC


Check if your camera really is RVC

Please, Press the Buttons [Image: postbit_thx.gif] and [Image: postbit_reputation.gif] if This post help or is usefull for you! Not is needed write just only thanks in Threads thumbsup
Quote this message in a reply
29-06-2019, 15:12 PM,
Post: #9
RE: ICAM will not code on the Bench
(29-06-2019, 11:20 AM)ruben_17non Wrote:  
(29-06-2019, 03:29 AM)Mizta Insane Wrote:  Do I need a terminating resistor?

yes, i never mount icam rvc but im sure 99,9%, terminating resistor is need. buy is cheap.

i first step i mean in retrofit icam rvc. but only one camera is possible mount. and i want front and rear camera. by this i decide mount icam high module.

[Image: attachment.php?attachmentid=1692643&stc=...04241http:]

Number 3 is for camera icam high 360
Number 4 is for camera icam RVC


Check if your camera really is RVC
I looked at the connector and I have icam rvc.
Quote this message in a reply
30-06-2019, 14:46 PM,
Post: #10
RE: ICAM will not code on the Bench
I bought a 120ohm can bus resistor. Hopefully it is the right one for k can 3.
Quote this message in a reply


Possibly Related Threads…
Thread Author Replies Views Last Post
XZBMW FSC Code for Route Maps Bimmer540 229 33,638 Yesterday, 18:40 PM
Last Post: nikisard
XZBMW REQUEST FSC CODE muskatas 4,242 348,040 Yesterday, 08:06 AM
Last Post: Kareta_BMW
  G05 KAFAS4 enable code missing after Retrofit ACC 6ergsm 19 2,302 26-03-2024, 12:33 PM
Last Post: Hodgsonp
XZBMW Tool for bench read 8hp Garryq 9 1,571 26-03-2024, 09:32 AM
Last Post: skywoker
  Bosch MEVD172H bench backup mrproper 1 249 23-03-2024, 18:43 PM
Last Post: Ratnik1990
XZBMW BMW Navigation Maps FSC activation code (request) rogerkj71 75 10,460 19-03-2024, 10:31 AM
Last Post: evaldazj
XZBMW F40 icam retrofit on entrynav2 Bavrian 8 319 17-03-2024, 10:18 AM
Last Post: Lpapp
XZBMW How to change VIN code in VCM via Esys? vipsha 5 1,337 14-03-2024, 22:20 PM
Last Post: tcp443
ZSkoda NBTEvo FSC lifetime Code for Road Map vladmir1 27 6,634 29-02-2024, 07:45 AM
Last Post: Jack79
  Code out active steering xMoses 1 150 29-02-2024, 01:21 AM
Last Post: BimmerSLO

Forum Jump:


Users browsing this thread:
2 Guest(s)

Return to TopReturn to Content