[Luky27]

Hi friends,

I need a flash file for DQ250 02E927770AD 2005
SW 0821

Altered with gear translation- relation from original gearbox HFQ (O2E) to SGH (02E).

So the gear translation must be taken from DQ250 02E927770AS  08.04.2016

Remarks:
- I have an excel with the gear translation differnces that I can send.

Any help will be appreciated very much

Cheers and nice day!

Luky

[rs@chip]

Hi friends,

I need a flash file for DQ250 02E927770AD 2005
SW 0821

Altered with gear translation- relation from original gearbox HFQ (O2E) to SGH (02E).

So the gear translation must be taken from DQ250 02E927770AS  08.04.2016

Remarks:
- I have an excel with the gear translation differnces that I can send.

Any help will be appreciated very much

Cheers and nice day!

Luky

read old flash and write to new gearbox..or clearly write exect flash no. from old one so we can find it for you

[Luky27]

Ok, I'll try to read the flash data from old DQ250 probably Thursday (as my car stands in a garage in another city).

I can not write it to the new DSG I think:
there was a communication problem with the new DQ250 (2016) either because of bad connection or because it is too new for the 2005 ECU.

Anyhow
- I'll try to send it here
- hope someone can send me a flash file.

Requirements:
 - works on above mentioned old (2005) DQ250, ECU (Original) and IMMO.
 - gear translation ratios for SGH (02E)

[Luky27]

Tried to read the current flash file from the DQ250 (old one see above)
using the original VCP

still I can't do it without the TCU LOGIN

Anyone can help? 

Thank you!

[birchbark506]

might need to use odis, cmd now dose bench back up of TCU and so dose magic motor sport flex.

[Luky27]

read old flash and write to new gearbox..or clearly write exect flash no. from old one so we can find it for you
[/quote]

I don't need the old flash on the new mechatronic.
I need a mix from 2 flash files into 1 flash file ... see problem description above.

Thank you

---

I got further information from George from evosoft.

1. SGH gearbox actually is 09D ... NOT 02E  (seller fooled me)
2. pre defined ***map packs*** needed to take gear ratio.
3. file with map packs is ***0D9300042N***
4. VCP can NOT be used to flash bin files to SGH gearbox.

Professional flash builder needed for:

1. take ratio maps from above mentioned file.
[George]
2. In order to make a file for your ODIS few things must be done :
- Convert the SGO of your mechatronic into BIN.
- Convert the FRF from 0D9 into bin
- Extract the gear ratio from 0D9 , add them to 02E file.
- Convert the 02E file from BIN to SGO so you can flash with ODIS.
[\]

Can someone do that?

[Luky27]

I got the flash file as .bin and .hex ... and we tried to flash it with original (!) ODIS in official VW workshop (garage) with "programming (Offline)":

- the file was put to the Panasonic PC in Drive C / ODIS / datflash
- we got an (official) login code from the official VAG Import Company (AMAG Switzerland) which is needed for offline software programming.
- after entering the Login ( again this is needed because we need to use "programing offline" as we don't have an official flash file from VW )
- the process starts with the usual message "do not interrupt until finished" or similar
BUT THEN:
- progress stays on "0%" and doesn't move forward... even after 20 minutes.

Anyone any idea?

Thank you!!!!