[bmwtechnophobe]

Hey guys
I'm flashing a '12 F10 and received some weird "negative response errors" when attempting to flash VTG/LMV module. The errors are weird because the module is able to be FDL coded before and after the failed flash attempts and the module was successfully flashed by the same computer and ENET cable just weeks before. Anybody here knows what's happening? The purpose of the flash is to update BLTD & SWFL files

Abbreviated Log info is below and full warning Log is attached:

Read SVT before TAL execution started.

TAL execution started.
ExecutionID=2019/07/17-15:07:03.574
[] job failed with negative response error: 
 code: repeat job
 description: Service RC_EM_IE returned a negative response with response code requestOutOfRange; LinkName: LMV_FR_19_ETHERNET
 severity: ERROR
 [THROWABLE]
[LMV_FR - 19] -MessageID is used multiple times, so MessageText may be ambiguous-job failed with negative response error: 
 code: repeat job
 description: Service RC_EM_IE returned a negative response with response code requestOutOfRange; LinkName: LMV_FR_19_ETHERNET
 severity: ERROR

 ....    .......    .....

TAL execution finished [TAL_EXECUTION_FINISHED]
TAL-Execution finished with status: "FinishedWithError". [C207]
TAL execution finished. Duration: "1min 27s". [C206]

Read SVT after TAL execution started.
Read SVT after TAL execution finished.

[rana]

you can still see the module on ista?

[bmwtechnophobe]

you can still see the module on ista?

Yeah, it's listed in ISTA - I can see the individual ECU information like see program date, Terminal voltage, and current software. unfortunately, this unit has the SWFL and BLTD for the ATC-50 Transfer case and the F10 has an ATC-35L. So the car is throwing drivetrain codes for incorrect transfer case installation and not allowing the trans to shift out of 1st.

[masa52]

use 3.27.1
I had a lot of strange errors using latest versions above 3.30 version

[shawnsheridan]

use 3.27.1
I had a lot of strange errors using latest versions above 3.30 version

With 4.18.x PSdZData, CAFD Injection and Flashing requires newer E-Sys, as E-Sys 3.27.1 will not work.

[bmwtechnophobe]

The most current PSDZ I have are the 4.17.X. Dodge the whole 4.18 compatibility issues though I'm wondering if 4.17.x has some sort of flashing security built into BTLD files or glitches for F models like we are seeing with 4.18. (Paranoid I know, but I don't underestimate BMW AG). I'm attempting unsuccessfully to get my hands on an older set of PSDZ say from 2014 -2013 and load into 3.27.1 E-sys to attempt the flash.

[Levanime]

did u figure it out?

[bmwtechnophobe]

A pretty busy week for me not much time to bang my head against a wall attempting to sort this out. Incredibly frustrating

Today, I set out to diagnose what does work and what does not starting at the ZGM and working my way down through the Busses. The car was successful in flashing the BTLD and SWFL files in the ZGM and writing a new I-Level, however, that's where the fun ended. Every other module attempted (including the LVM ) experience the mentioned ecu request out of range error.

Next, I opened Tool32 and ran "is_lesen" on the ZGW_01 and found 9 errors waiting for me. the last few errors are concerning and the translated file is attached below. I think it's time to get my hands on a new (used) ZGM and see if the ethernet on my current ZGM is fried. If that's the case it's all good as I'm planning on completing a LCI adaptive headlight upgrade anyway. I'll order the ZGM High with MOST and FRM at the same time.

I'll update this saga when the replacement ZGM arrives

[snf11lci]

use 3.27.1
I had a lot of strange errors using latest versions above 3.30 version

With 4.18.x PSdZData, CAFD Injection and Flashing requires newer E-Sys, as E-Sys 3.27.1 will not work.

What version you recomend? 
3.32.1 is OK?  or better is other one ?

[bmwtechnophobe]

snf11lci

I use E-Sys 3.33.1 and 3.27.2(Tokenmaster's Launcher) with good success on PSDZ files 4.17.X and below