Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
What is the difference between the two OEM (Clone) XENTRY VCIs?
26-07-2019, 12:49 PM,
Post: #11
|
|||
|
|||
RE: What is the difference between the two OEM (Clone) XENTRY VCIs?
(26-07-2019, 12:36 PM)sascha965 Wrote: Here some Pictures of Xentry VCI Clone. Thank you for pictures, to me seems that it is repacked VXDiag "c6" doip. Does it require install VXDIAG drivers? Can it be used wirelessly? Do you use ordinary Xentry openshell or Xentry openshell passtrough? Best regards! |
|||
26-07-2019, 14:07 PM,
(This post was last modified: 26-07-2019, 14:07 PM by sascha965.)
Post: #12
|
|||
|
|||
RE: What is the difference between the two OEM (Clone) XENTRY VCIs?
You can use ordinary XDOS without VXdiag Driver.
Only config ecom and ready. No wireless or wifi, usb and lan only. |
|||
Reputation: +2 - getaibose [+1] , pesona [+1] | |||
26-07-2019, 14:30 PM,
(This post was last modified: 26-07-2019, 14:31 PM by getaibose.)
Post: #13
|
|||
|
|||
RE: What is the difference between the two OEM (Clone) XENTRY VCIs?
|
|||
11-08-2019, 07:44 AM,
Post: #14
|
|||
|
|||
RE: What is the difference between the two OEM (Clone) XENTRY VCIs?
New c6 is disappeared from aliex, some one saw That Too?
|
|||
11-08-2019, 16:34 PM,
Post: #15
|
|||
|
|||
RE: What is the difference between the two OEM (Clone) XENTRY VCIs?
As I know Xentry kit 3 VCI don´t use SDConnect toolkit for connection between Xentry and device. So again it is not clone of Bosch Xentry kit 3 VCI.
|
|||
Reputation: +1 - pesona [+1] | |||
12-08-2019, 21:52 PM,
Post: #16
|
|||
|
|||
RE: What is the difference between the two OEM (Clone) XENTRY VCIs?
C6 Clone aka VXDIAG is a piece of shit, it is very unstable, wifi device has a very weak signal while working and connecting to control units it is stuck and throwing communication errors.
I used C4 to finish my work, my advice don't buy this shitty damn device |
|||
28-08-2019, 07:22 AM,
Post: #17
|
|||
|
|||
RE: What is the difference between the two OEM (Clone) XENTRY VCIs?
(26-07-2019, 14:30 PM)getaibose Wrote:(26-07-2019, 14:07 PM)sascha965 Wrote: You can use ordinary XDOS without VXdiag Driver. It doesn't work with older DAS vehicles. Doip is working. |
|||
10-09-2019, 06:04 AM,
Post: #18
|
|||
|
|||
RE: What is the difference between the two OEM (Clone) XENTRY VCIs?
I have the older VCXDiag C6 (the one without USB and ethernet on the side) and other than DOIP it has worked well for me with my May 2015 MY2016 W212 and I last used it about 8 weeks ago. I only use it personally on the one vehicle and not commercially though.
I don't use the WiFi side, only ever the USB or ethernet cable - I tend to stick to the ethernet cable. I never could get DOIP working - it passed the tests once in Xentry from 2018 with the manufacturer supplied HDD but as soon as the drivers updated it never worked again with that version and I spent hours messing around with it. I think they have an additional fudge in place somewhere to make the DOIP tests pass. The supplier did say that the new disk they had would work with DOIP but I never sent this one back to test it - I should get around to it at some point. For now I just used a fresh Windows 10 64 bit install with Xentry 07.2019 and the VCXDiag drivers and Xentry worked. I got the MB dealer to update my NTG5.1 in the end. I need to use it later as I'm having some hesitations when pulling away, not sure if it's a fault or just need to reset the transmission. |
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content