[ady_e_n]

Hi Guys, 

I'm trying to flash nbt Evo on a bench with ZGW2 but it keeps failing with the message that HU_NBT2 can't be switched to parallel programming. 

I managed to get the flashing started one time, however it started flashing on UDS and after 61 long hours of flashing, it failed at 63 %.

I'm trying to start the Ethernet flashing and avoid UDS but i don't know how exacly. 

Connection to OABR is correct, I can code the Head Unit, however in flashing terms, i'm failing miserably. 

Changed the TAL as well, to reflect the ZGW2, (changed from FEM)

The connection is made on VIN through ZGW.
BOth ZGW and HU have the same VIN

Not sure about the parameters though

Any ideas ?
Thanks

[sameur10]

Hi , try to ping hu ip adress to see if it is connected 169.254.199.99
Hu can be coded over CAN2 or ethernet , i think your OABR is not connected correctly

Br

[ady_e_n]

Hi , try to ping hu ip adress to see if it is connected 169.254.199.99
Hu can be coded over CAN2 or ethernet , i think your OABR is not connected correctly

Br

Hi Sameur, 

Thank you, i took a look at the OABR connection and noticed that something was incorrectly pinned. I re-pinned the connection and not i can ping the HU correctly 

What about E-sys?
 - What version of E-sys do you/ should i use ?
 - Regarding Parameters should i set in the Parameters tab under Tal execution ?

Thank you and best Regards

[alsamaraee]

Hi,
Which way will be faster to flash HU, over can2 or OARB?

[ady_e_n]

Hi,
Which way will be faster to flash HU, over can2 or ORAB?

Oabr obviously since it’s ethernet and the transfer speed is way faster than can2 (which if i’m not mistaking, should be around 1 mb/s)

[alsamaraee]

Hi ady,

Thank you for answering.

Can you please check my post?

https://cartechnology.co.uk/showthread.p...onal+clamp

[alsamaraee]

I have the hu-evo2 connected to ZGW2-4sk via can-bus. I made even ethernet cable to OARB connector but not wired to ZGW.
Tried to flash but get error C207.
What FA and I-steps should I use are they from the G-series that the HU come from or the one from my car F11(jan-2012)?
Should I connect as G/F?

<
TAL execution started.
ExecutionID=2022/04/24-11:03:31.152
[] prepareTALExecution started [PROGRESS]
[] prepareTALExecution finished [PROGRESS]
[] prepareVehicleForFlash started [PROGRESS]
[] prepareVehicleForFlash finished [PROGRESS]
MCDDiagService<id=230900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=DSC - DiagnosticSessionControl, description=error: timeout, link=HU_NBT2_63_ETHERNET_63> [DIAGSERVICE]
MCDDiagService<id=230900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=DSC - DiagnosticSessionControl, description=error: timeout, link=HU_NBT2_63_ETHERNET_63> [DIAGSERVICE]
MCDDiagService<id=230900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=DSC - DiagnosticSessionControl, description=error: timeout, link=HU_NBT2_63_ETHERNET_63> [DIAGSERVICE]
MCDDiagService<id=242900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=RC_SDB - RoutineControl SetDefaultBus, description=error: timeout, link=HU_NBT2_63_ETHERNET_63> [DIAGSERVICE]
[] Activate programming mode was not successful for: ECUId:HU_NBT2_0x63 [WARN]
[] ECUId:HU_NBT2_0x63 not accessible cause could not be switched to parallel programming mode [WARN]
[HU_NBT2 - 63] ECUId:HU_NBT2_0x63 not accessible cause could not be switched to parallel programming mode [THROWABLE]
[] ECUId:HU_NBT2_0x63 not accessible cause could not be switched to parallel programming mode [WARN]
[] finalizeVehicleFlash started [PROGRESS]
[] finalizeVehicleFlash finished [PROGRESS]
[] prepareVehicleForCoding started [PROGRESS]
[] prepareVehicleForCoding finished [PROGRESS]
[] finalizeVehicleCoding started [PROGRESS]
[] finalizeVehicleCoding finished [PROGRESS]
[] finalizeTALExecution started [PROGRESS]
[] finalizeTALExecution finished [PROGRESS]
TAL execution finished [TAL_EXECUTION_FINISHED]
TAL-Execution finished with status: "FinishedWithError". [C207]
TAL execution finished. Duration: "2min 13s". [C206]

Read SVT after TAL execution started.
Read SVT after TAL execution finished.
>
This is the log when I flshing via zgw. Get the blue screen on the HU and then reboot.