Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
OP-COM v6 with "fake MCU" REPAIR
11-01-2019, 08:06 AM,
Post: #81
|
|||
|
|||
RE: OP-COM v6 with "fake MCU" REPAIR
Thanks for reply that's what I thought my v6 is the opcom new version c22 and d5 are already removed and Kline is working haven't tested CAN yet only had to change pic18f to real one
what it latest release of software/database that can be used with these clones fantomels release ? If mine or others posts and info are helpful please give thanks/rep
|
|||
11-01-2019, 08:13 AM,
(This post was last modified: 11-01-2019, 08:15 AM by mattydr67.)
Post: #82
|
|||
|
|||
RE: OP-COM v6 with "fake MCU" REPAIR
The latest versions are 170823 one for English, German and Hungarian.
Maybe you wanna say the versions shared by fantomel from his collection because he didn't released anything. Opcom/vauxcom is AutoM3 tradmark. There are also HQ clone softwares versions for moded interfaces. Good luck |
|||
11-01-2019, 09:00 AM,
Post: #83
|
|||
|
|||
RE: OP-COM v6 with "fake MCU" REPAIR
Cheers m8 now I know you know where I can find HQ clone software and what latest version is for that or is it same 170823 ? And yeah my bad software is shared by fantomel not created
If mine or others posts and info are helpful please give thanks/rep
|
|||
11-01-2019, 10:53 AM,
(This post was last modified: 12-01-2019, 05:30 AM by mattydr67.)
Post: #84
|
|||
|
|||
RE: OP-COM v6 with "fake MCU" REPAIR
Hi
The only option that you have is to use Opcom china clone 08.2010 ( 100219a ) and vauxcom 120309a GB for any clone To use HQ clone softwares you need to flash your FTDI with a dump that must be generated for your ftdi chip id. To use original software you need license Good luck |
|||
09-06-2019, 15:30 PM,
Post: #85
|
|||
|
|||
RE: OP-COM v6 with "fake MCU" REPAIR
(20-06-2018, 11:04 AM)irarkh Wrote: It's piece a cake! Just remember to cut off pin 1 from pcb then connect it to pin 23 MCU which C22 pin is going directly to MCU. Thanks @irarkh the response! But do you did checked my PCB revision ? Do you seen C22 and D5 solder point ? because my PCB rev doesn't have them thus how connect those points ? regards Lajos. |
|||
09-06-2019, 18:17 PM,
(This post was last modified: 09-06-2019, 18:18 PM by mattydr67.)
Post: #86
|
|||
|
|||
RE: OP-COM v6 with "fake MCU" REPAIR
Sorry I checked your pics but I cannot see it well because I am using a cell phone. Did you changed the "fake" MCU with a real original PIC18F458? Did you reflashed it? Even you don't do any other hardware modifications you will be able to use the tool in CAN BUS car only. The modification in hardware are only for K-line cars comunications.
Good luck |
|||
09-06-2019, 20:11 PM,
Post: #87
|
|||
|
|||
RE: OP-COM v6 with "fake MCU" REPAIR
If you read my Post: #65 tell you all
Yes replaced with a real original PIC18F458 and flashed with external programmer proper. Only the hardware modification can't do, because in my PCB revision doesn't have C22 and D5 like this the result = can't talk with my car :/ if you are can check my picture (Post: #65) because need know my PCB revision, for " how to newer modbo get to working" |
|||
10-06-2019, 04:41 AM,
(This post was last modified: 10-06-2019, 07:14 AM by mattydr67.)
Post: #88
|
|||
|
|||
RE: OP-COM v6 with "fake MCU" REPAIR
Mate I've seen that pictures and as I said I cannot see well.
"D5" it is not soldered in your hardware even there is the footprint for it "C22" it is actually "C11" on your hardware - so remove it Good luck |
|||
12-06-2019, 13:46 PM,
Post: #89
|
|||
|
|||
RE: OP-COM v6 with "fake MCU" REPAIR
|
|||
12-06-2019, 14:14 PM,
(This post was last modified: 12-06-2019, 14:36 PM by mattydr67.)
Post: #90
|
|||
|
|||
RE: OP-COM v6 with "fake MCU" REPAIR
If you have a genuine tool you have to install the original software and you have to have the interface pluged to the USB at least and internet connecton activated.
Then start the opcom software then choose Diagnostic and an Activation windows will show up. Use Online Activation button You get the license.dat ( activation ) automatically. Well you can get activation offline. This is the other choice. Good luck |
|||
« Next Oldest | Next Newest »
|
Possibly Related Threads… | |||||
Thread | Author | Replies | Views | Last Post | |
REPAIR ERASED OP-COM CLONE BOOTLOADER FROM PIC18F458 MCU | fantomel | 190 | 133,498 |
17-11-2023, 12:03 PM Last Post: mattydr67 |
|
GM MDI2 REPAIR EXPERIENCE | 12manux | 1 | 224 |
03-10-2023, 19:24 PM Last Post: apol |
|
Opcom Bootloader Repair with TL866 ICSP port | aki1 | 3 | 1,622 |
07-10-2019, 13:07 PM Last Post: avepla |
|
opcom clone need help to repair | autosolutions | 1 | 814 |
18-09-2019, 02:40 AM Last Post: mattydr67 |
|
Op-Com Repair Tool | ircpoLice | 44 | 48,909 |
25-08-2019, 05:40 AM Last Post: itman |
|
Opel meriva 1.6 xe ecu repair help | davor.touch | 5 | 2,838 |
03-05-2017, 08:43 AM Last Post: dil6222 |
|
Corsa C,central locking not working-BCM repair(SOLVED) | grmsek.damjan | 0 | 2,195 |
16-06-2015, 08:02 AM Last Post: grmsek.damjan |
|
Y17DT repair | cicko | 1 | 1,296 |
12-06-2015, 08:10 AM Last Post: domelec |
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content