[BMWF01]

Hello Members 

Line     Base Variant      Missing SWE
-----------------------------------------------------
          EPS            btld_00000467-013_002_000
                           
                           hwel_000009f2-002_003_001
                           hwap_000009f6-255_255_255
  
TAL execution started.
ExecutionID=2019/08/09-07:41:01.254
[EPS - 30] - [Exception - EPS - 30] SVK-Ist does not match expected SGBMIDs for ecu ECUId:EPS_0x30. Excpected (relevant process classes only): [hwel_000009f2-002_002_002, hwap_000009f6-255_255_255], Actual (relevant process classes only): [hwel_000009f2-002_003_001, hwap_000009f6-255_255_255], Missing SGBMID(s): [hwel_000009f2-002_002_002], Surplus SGBMID(s): [hwel_000009f2-002_003_001]
TAL-Execution finished with status: "FinishedWithError". [C207]
TAL execution finished. Duration: "1min 0s". [C206]

TAL execution started.
ExecutionID=2019/08/09-07:49:35.467
[EPS - 30] - [Exception - EPS - 30] SVK-Ist does not match expected SGBMIDs for ecu ECUId:EPS_0x30. Excpected (relevant process classes only): [hwel_000009f2-002_003_000, hwap_000009f6-255_255_255, btld_00001089-006_000_000], Actual (relevant process classes only): [hwel_000009f2-002_003_001, hwap_000009f6-255_255_255, btld_00001089-006_000_000], Missing SGBMID(s): [hwel_000009f2-002_003_000], Surplus SGBMID(s): [hwel_000009f2-002_003_001]
TAL-Execution finished with status: "FinishedWithError". [C207]
TAL execution finished. Duration: "59s". [C206]

..........................................................
There is no HWAP and HWEL in my Psdzdata folder.
Anyone have these Process Class and their IDs?

Im requesting Missing SGBMID:
hwel_000009f2-002_003_000], hwap_000009f6-255_255_255, btld_00000467-013_002_000

i need these files

[The CaT]

You should read something about what HWEL and HWAP class processes are.

[BMWF01]

You should read something about what HWEL and HWAP class processes are.

Why don't you shed light on hwel and hwap?

[The CaT]

Why don't you shed light on hwel and hwap?

0x01 HWEL Hardware (Elektronik)

0x02 HWAP Hardwareauspraegung

[lustek]

I think you set wrong shipment i-level or EPS was replaced

[VroomVroom]

You can change shipment I-step or open Tal editor and edit Tal and delete next lines “Expected”
save Tal and flash again

[HU_man]

Delete EPS in SVT soll before cal TAL, you will be fine.

[BMWF01]

Delete EPS in SVT soll before cal TAL, you will be fine.

I have replaced the EPS with a used unit and you said i should delete "EPS" from SVT_Soll?
Then after i edit the SVT_soll of removing "EPS" then save it and then load it then Then Calculate Tal.xml?

So if i'm not wrong to say this: SVT_ist (Actual installation Table) will retain the actual EPS from factory and all its SWEs. If i delete "EPS" from SVT-soll then save it and then load it under KIS/SVT target, then after i calculate Tal.xml
it would be fine to flash with or without "EPS" module?

[BMWF01]

Delete EPS in SVT soll before cal TAL, you will be fine.

I have replaced the EPS with a used unit and you said i should delete "EPS" from SVT_Soll?
Then after i edit the SVT_soll of removing "EPS" then save it and then load it then Then Calculate Tal.xml?

So if i'm not wrong to say this: SVT_ist (Actual installation Table) will retain the actual EPS from factory and all its SWEs. If i delete "EPS" from SVT-soll then save it and then load it under KIS/SVT target, then after i calculate Tal.xml
it would be fine to flash with or without "EPS" module?

I did not delete TRSVC nor EPS from svt_soll.

so instead i ask client to buy an ICOMA2 from China then: after ICOM arrived i connect to BMW F30 and Start -up Esys Pro>then connect BMW F30 via ICOM/Ethernet with IP of Tcp://169.254.92.38:50160> Then Establish connection. I click comfort mode on Esys>Then select target-selector for latest i-level target> Project=F020_19_07_539_004_002_000, vehicle info=F020

After connection is established:
Read out FA? Then save FA>Then click read VCM>save as svt_ist>Then click Activate FA to expand Vehicle Profile: this will make active both the "I-step shipment" and "i-step Target"  boxes>then click complete flash>Then click calculate SVT_Soll:after svt_soll as finish calculation?the click on "HWID- from SVT_actual">then save SVT_Soll>then click on Tal Calculate:After Tal has finish Calculation>save as Tal.xml

This time no errors comes up for"TRSVC" SWEs missing.

Then i click on Expert Mode>then click on TAL processing: Then select TAL.xml>then click on SVT_soll.xml [...]and load SVT_Soll>then click on Read FA out of VCM:

Now on the ECU column: The Tal list showed the ECU for flashing in checked off boxes: created on ID Base row:
Then click on All to uncheck all the ECU marked for flashing: then select only my client's EPS module in ECU column:>then make sure i checked SWdeploy and CDdeploy>for EPS: then check for software availability>Then if its says all SWEs are there> then click "START" to run the processing of the Transaction list (TAL.XML) and wait for the EPS to start flashing and encoding.

Here is the video of the Process: https://www.youtube.com/watch?v=rHHzV3gA...e=youtu.be

[HU_man]

Delete EPS in SVT soll before cal TAL, you will be fine.

I have replaced the EPS with a used unit and you said i should delete "EPS" from SVT_Soll?
Then after i edit the SVT_soll of removing "EPS" then save it and then load it then Then Calculate Tal.xml?

So if i'm not wrong to say this: SVT_ist (Actual installation Table) will retain the actual EPS from factory and all its SWEs. If i delete "EPS" from SVT-soll then save it and then load it under KIS/SVT target, then after i calculate Tal.xml
it would be fine to flash with or without "EPS" module?

Oh sorry , i think you flash another ecu then got error EPS request files