[apoelistas]

I found a new method for activation of keyless entry. I am waiting for a confirmation.
SRT Can-Connect.


   

So to sum up 3 available options
1. VCP using the zdc parameter file
2. Odis-E but we do not have any information how this is done
3. SRT Can-Connect

[yang1120]

What is the part number of your car's J393? Can you sweep me?

---

The original car J393 part number is 8k0907064CQ it? This number does not support advanced keys. Need to replace the comfort module J393.

[apoelistas]

I have start stop button working without inserting key (advance key in my pocket) and steering wheel also unlocks when I press the start button. 8K0907064CQ is the latest bcm2 comfort unit for pre facelift (eu version) which supports keyless Go (I have cross referenced this to german forums, my audi dealer and etka 7.5). However keyless entry parameter was not uploaded by Audi during key specific actual svm online comparison.

I am 100% sure of this. Also The comfort unit comes with the extra pins for adding the newly created keyless 27 pin blue connector in the luggage compartment.

Back to original question. Can you help with odis engineering to add keyless entry parameter in 05 immobilizer which is part of comfort unit (046)Thanks.

Do you want me to attach the 05 immobilizer pseudo control unit xml if that helps??

Looking forward for your reply.

I have uploaded the message I get from Can-Connect.
Can anyone translate this Russian to me?? I cannot copy the text in order to translate. I think it is error message, contact support
   

It is amazing that my Q5 can be read and flashed with obdlink SX usb and this can-connect program (actually I did not succeed yet since I am waiting for support to confirm compatibility and to respond regarding this error message)

[apoelistas]

With odis engineering
To save the xml parameter file of all control units, I need the security codes of some modules:
3, 8, 9,17 ,46 ,53 (I have cancelled at 53 ).

Does anyone have he security codes for odis engineering for B8 (A4 A5 Q5)???? I get this prompt at the control modules when trying to read parameters.
Thanks

[yang1120]

8K0907064CQ on the ETKA is displayed on the PR number 5D7 (zentralverriegelung mit funkfernbedienung ohne panik-taste), the control unit is not advanced into the system, you can not brush parameters and code to complete the conversion project, you can try 05 0 bytes no way to modify the code, the Audi car into the advanced function I changed a lot, if necessary, you can send an email: [email protected]

[apoelistas]

Not to worry. Yes it is displayed as 5D7 but if your car had already keyless entry, the parameters are copied to the comfort unit during SVM actual/spec comparison when installing the comfort unit because this comfort unit supports in hardware keyless entry.

CQ is the latest replacement for pre facelift comfort units (with or without advance key).

There was just one method known to me that can add this parameter back in case of retrofit. That was VCP.

However I just found another solution, whithout having to buy VCP.

I just used SRT CAN-Connect program with my obdlink SX usb. I had it because it is the best obd2 diagnostic and really cheap, but it is also supported (USA made).

Support replied to me first, they asked me to save the parameter of my keyless / comfort (with their program), they then enabled my firmware so I would not get the error message. They confirmed to me that I can now flash. Then I bought the tokens.

Parameter was flashed successfully with CAN-Connect (ru) just less than an hour ago. Price 90 euros. Flash time 5 seconds.

4 keyless entry sensors working.
Boot working.

No need to hold the advance key anymore and push the buttons.
SUCCESS

[buscalios]

Good morning. They could, again, activate the download file (a5PA_start_auth_8K0907064Cx, Kx.zdc.txt). Thank you