Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Solved ✔ AFS PROGRAMMING WITH ISTA P fails
25-08-2019, 21:41 PM,
(This post was last modified: 28-08-2019, 13:16 PM by Clusters.)
Post: #1
|
|||
|
|||
AFS PROGRAMMING WITH ISTA P fails
Hey, i have a problem with a Update.
I did a ilevel update with a kcan cable and all went through but on AFS module (AL on ISTA) the Programming went till 50% and then shows capi error.... on winkfp i get Security access denied error. With this cable I already updated the ilevel on a lot of cars and never had problems. (Updated firmware) Now i tried with a geniue ICOM Next and i got the same error. I tried SP DATEN v61 and v41. Do you have a idea to help? The next would be to buy a new AFS Module but they are pretty expensive |
|||
26-08-2019, 05:08 AM,
Post: #2
|
|||
|
|||
RE: AFS PROGRAMMING WITH ISTA P fails
Can you show us the UIF page from INPA or Gini?
Does the module show up in ISTA? |
|||
26-08-2019, 07:49 AM,
(This post was last modified: 26-08-2019, 07:58 AM by venix.)
Post: #3
|
|||
|
|||
RE: AFS PROGRAMMING WITH ISTA P fails
It shows up.
Uif is unwritten the vin is y?????? And the module stays in programming state It shows a flash error Winkfp shows= 2089 PABD 06FLash Programmieren 2544 Switching Programming mode failed 10FLASH.DIAGNOSE 2086 PABD 06Flash Programmieren 3352 Signature check Failed 10FLASH, FLASH_SIGNATUR 2086 Error COAPI2.cco CoapiRunCabd 6 Signature Check Failed SG-PROGRAMMIERE 2086 Error CoapiKfProgSgD2 19 Signature Check Failed |
|||
27-08-2019, 13:57 PM,
Post: #4
|
|||
|
|||
RE: AFS PROGRAMMING WITH ISTA P fails
somebody an idea ?
|
|||
27-08-2019, 14:09 PM,
Post: #5
|
|||
|
|||
RE: AFS PROGRAMMING WITH ISTA P fails
i would first try with ISTA-P and ICOM. last i would try is to manually update the module with winkfp in expert mode but without booting sector
|
|||
27-08-2019, 17:12 PM,
Post: #6
|
|||
|
|||
RE: AFS PROGRAMMING WITH ISTA P fails
I already tried with icom and istap.
In winkfp i have the error i mentioned abve |
|||
27-08-2019, 17:31 PM,
Post: #7
|
|||
|
|||
RE: AFS PROGRAMMING WITH ISTA P fails
Ok, so it looks like data got corrupted by the K+DCAN cable. That's why the VIN is wrong and UIF is blank. I would use FindECU with the part number to attempt to find a valid ZB for that module. Then either correct the ZB info on the module with Tool32 and attempt a flash with ISTA-P, or flash with WinKFP.
|
|||
28-08-2019, 11:25 AM,
Post: #8
|
|||
|
|||
RE: AFS PROGRAMMING WITH ISTA P fails
I flashed the dcan cable with https://github.com/uholeschak/ediabaslib.
now reprogrammed all the car with ista p and working now. so dcan cable is better then icom |
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content