[PopDog]

I have two MIB2 Units. One AU57x MIB2 on K3663 and one from Q7 with MIB2 AUG22.

There is something going around where you patch the MIBRoot Application, but if something goes wrong, serial access is needed (not telnet!)

On the AU57X MIB2 it already gone wrong and MIB2 booting only with Audi Logo and ethernet Adapter has lights, but telnet is closing the connection itself. For recovery a Serial Connection over USB UART/TTL Adapter to the J5 / RCC Area is needed. 

I found a Image of a VW Discover Pro MIB2/Porsche PCM an here it shows at B3 and B9 the Connection to J5. This is not working on the AUG22 Unit and on the AU57x not tested till now. 



Today i removed the blue and green plugs from quadlock on AUG22 MIB2, and tested all pins which are not used to receive some output, but found nothing. (Only RX/GND on TTL Adapter used to find) 

Does somebody know, if there are pins on the quadlock for j5/rcc for one of this Units? And when which Pins are the right ones?

Also removed the board from the case of the AU57x Unit. There are also two PCI-Express like ports one with J5/V850 writing on it. Maybe someone knows here, which pins are the right ones to connect? GND is not the problem to find but rx,tx

[mft133]

Your pinout is correct - blue connector (block B) pin 3 and 9. Connect GND of usb-serial converter to pin 7.

I have two MIB2 Units. One AU57x MIB2 on K3663 and one from Q7 with MIB2 AUG22.

There is something going around where you patch the MIBRoot Application, but if something goes wrong, serial access is needed (not telnet!)

On the AU57X MIB2 it already gone wrong and MIB2 booting only with Audi Logo and ethernet Adapter has lights, but telnet is closing the connection itself. For recovery a Serial Connection over USB UART/TTL Adapter to the J5 / RCC Area is needed. 

I found a Image of a VW Discover Pro MIB2/Porsche PCM an here it shows at B3 and B9 the Connection to J5. This is not working on the AUG22 Unit and on the AU57x not tested till now. 



Today i removed the blue and green plugs from quadlock on AUG22 MIB2, and tested all pins which are not used to receive some output, but found nothing. (Only RX/GND on TTL Adapter used to find) 

Does somebody know, if there are pins on the quadlock for j5/rcc for one of this Units? And when which Pins are the right ones?

Also removed the board from the case of the AU57x Unit. There are also two PCI-Express like ports one with J5/V850 writing on it. Maybe someone knows here, which pins are the right ones to connect? GND is not the problem to find but rx,tx

[turboblade]

Any luck with this?

I have two MIB2 Units. One AU57x MIB2 on K3663 and one from Q7 with MIB2 AUG22.

There is something going around where you patch the MIBRoot Application, but if something goes wrong, serial access is needed (not telnet!)

On the AU57X MIB2 it already gone wrong and MIB2 booting only with Audi Logo and ethernet Adapter has lights, but telnet is closing the connection itself. For recovery a Serial Connection over USB UART/TTL Adapter to the J5 / RCC Area is needed. 

I found a Image of a VW Discover Pro MIB2/Porsche PCM an here it shows at B3 and B9 the Connection to J5. This is not working on the AUG22 Unit and on the AU57x not tested till now. 



Today i removed the blue and green plugs from quadlock on AUG22 MIB2, and tested all pins which are not used to receive some output, but found nothing. (Only RX/GND on TTL Adapter used to find) 

Does somebody know, if there are pins on the quadlock for j5/rcc for one of this Units? And when which Pins are the right ones?

Also removed the board from the case of the AU57x Unit. There are also two PCI-Express like ports one with J5/V850 writing on it. Maybe someone knows here, which pins are the right ones to connect? GND is not the problem to find but rx,tx