[Drimacus]

Hi Everybody.
I got problems with lastest psdzdata.
When i use it esys does like in attachment.

Earlier versions no problems at all. 

Esys 3.33.4

Any Hint for me?
Thank you in advance.

[Mr_R]

Hello.

Have exactly the same mistake with my system. Unfortunately, I have not found a solution yet.

[Stromag]

Reinstall E-Sys, then it should work.

[Mr_R]

I did it several times yesterday. Can not select an I level at PSdZ 4.19.13. Have tried the E-SYS 3.33.1 and the 3.33.4 - no chance. The older PSDZ works perfectly.

[Stromag]

I did it several times yesterday. Can not select an I level at PSdZ 4.19.13. Have tried the E-SYS 3.33.1 and the 3.33.4 - no chance. The older PSDZ works perfectly.

Otherwise, the location of the PSdZData is incorrect, Or the PSdZData are damaged. or Esys needs to be reinstalled. Everything runs smoothly with me, no matter which Esys version ..

[Mr_R]

Hello.

I think that the PSdz data are damaged. The storage location for PSdZ data is correct, so I'm very sure. The vehicles can be connected under the connection selection. Only the I levels are not selectable. The older PSdZ data run without problems. I re-installed E-Sys 3.33.1 as well as 3.33.4 several times yesterday. This action has brought no solution. As before, only the older PSdZ data are running. I'll reload the PSzD data and try again. Perhaps an error occurred while loading / unpacking. Thank you for your suggestions.

Greetings from Germany

[shawnsheridan]

Hello.

I think that the PSdz data are damaged. The storage location for PSdZ data is correct, so I'm very sure. The vehicles can be connected under the connection selection. Only the I levels are not selectable. The older PSdZ data run without problems. I re-installed E-Sys 3.33.1 as well as 3.33.4 several times yesterday. This action has brought no solution. As before, only the older PSdZ data are running. I'll reload the PSzD data and try again. Perhaps an error occurred while loading / unpacking. Thank you for your suggestions.

Greetings from Germany

I have same issue with v.4.19.xx.  Whatever the cause, it lies within the original psdzdata from ISTA as I use original ISTA psdzdata not the ripped psdzdata packaged and uploaded here.

For now, for CAFD Injection and Flashing, you must stick with v.4.18.33_PSdZData_Full.

[BugFix]

Hi Everybody.
I got problems with lastest psdzdata.
When i use it esys does like in attachment.

Earlier versions no problems at all. 

Esys 3.33.4

Any Hint for me?
Thank you in advance.

If you use PSDZDATA from mr shawnsheridan


He did fuскed upload

Have to open  C:\DATA\psdzdata\kiswb\F020\KIS..properties

and have to remove one point KIS..properties -> KIS.properties

[duncanduncan]

Hi Everybody.
I got problems with lastest psdzdata.
When i use it esys does like in attachment.

Earlier versions no problems at all. 

Esys 3.33.4

Any Hint for me?
Thank you in advance.

If you use PSDZDATA from mr shawnsheridan


He did bad upload

Have to open  C:\DATA\psdzdata\kiswb\F020\KIS..properties

and have to remove one point KIS..properties -> KIS.properties

Shawn is highly respected here and I'm sure he didn't do anything wrong with uploading. Pls don't badmouth him. As he stated above problem is in ORIGINAL psdzdata as well.

[shawnsheridan]

If you use PSDZDATA from mr shawnsheridan 

He did bad upload

Have to open  C:\DATA\psdzdata\kiswb\F020\KIS..properties

and have to remove one point KIS..properties -> KIS.properties

Good catch,  In v.4.19.13_PSdZData_Full, some chassis have both KIS..properties, and KIS.properties, and some have only KIS..properties, and the latter will fail.  This is how it came from BMW ISTA though, not some botched packaging.  In v.4.19.21 ISTA it is fixed.