Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

BMW F20 116i DME Update
17-10-2019, 13:30 PM,
Post: #1
BMW F20 116i DME Update
Hi,

The issue I am having with the car is that 'Drivetrain' error pops up intermittenly but if I switch off and start again it seems fine again until next time.
I have hooked up ISTA D and it comes up with error 0x11A002 'High pressure fuel, plausibility Pressure too Low'.
So far I have replaced the pump with 2 more working used pumps and still the same issue plus changed the injectors and fuel rail regulator.
Maybe there is a hardware error in DME  but  I was hoping to try updating the DME first and see the outcome.
I am also open to other suggestions from members as well.

I am seeking some guidance on updating my DME ecu, I have working Bmw E-Sys ver 3.25.3 with ethernet cable.

I have managed to as far as read the FA, SVT and TAL calculation under Comfort Mode.
Gone into Expert Mode loaded and Read FA, then selected DME only and verified software availability to be ok.
Next step would be to start the operation...have I missed anything before I start to update?

Thanks in advance
Quote this message in a reply
17-10-2019, 13:41 PM,
Post: #2
RE: BMW F20 116i DME Update
I recomend at least to work with esys 3.27, or to download last version, with datens.
Steps are ok.
I can help you to flash the DME
Quote this message in a reply
17-10-2019, 14:00 PM,
Post: #3
RE: BMW F20 116i DME Update
(17-10-2019, 13:41 PM)jaramillo Wrote:  I recomend at least to work with esys 3.27, or to download last version, with datens.
Steps are ok.
I can help you to flash the DME

Thank you for your offer, so best to re-install E-Sys ver 3.27 and latest datens..would you be able to direct me for download?

By the way, the version I have is not good for updating?
Quote this message in a reply
17-10-2019, 14:11 PM,
Post: #4
RE: BMW F20 116i DME Update
Esys
https://cartechnology.co.uk/showthread.php?tid=51615

Latest datens:
https://cartechnology.co.uk/showthread.php?tid=57895
Quote this message in a reply
17-10-2019, 14:42 PM,
Post: #5
0Scope  RE: BMW F20 116i DME Update
(17-10-2019, 14:11 PM)jaramillo Wrote:  Esys
https://cartechnology.co.uk/showthread.php?tid=51615

Latest datens:
https://cartechnology.co.uk/showthread.php?tid=57895

Cheers, I'll get this downloaded and set it up soon. Thanks again
Quote this message in a reply
17-10-2019, 15:45 PM,
Post: #6
RE: BMW F20 116i DME Update
For your fault, have you also check the Integrated supply module (12637614585) and Fuel pump relay (61366915327)?

I've seen these 2 parts also make trouble to the fuel pump.
Quote this message in a reply
17-10-2019, 16:35 PM,
Post: #7
RE: BMW F20 116i DME Update
(17-10-2019, 15:45 PM)simonchs Wrote:  For your fault, have you also check the Integrated supply module (12637614585) and Fuel pump relay (61366915327)?

I've seen these 2 parts also make trouble to the fuel pump.

Yes, I have checked low pressure pump relay and thats working fine. Now regarding Integrated Supply Module..is this what is refered to as ICM? If so, then I have had 'No message' missing between ICM and DME but does not come up everytime only High pressure pump plausibilty. The pressure from Low pump into High pump is around 68psi
.
Quote this message in a reply
17-10-2019, 17:19 PM,
Post: #8
RE: BMW F20 116i DME Update
Is fuel pressure the only code in dme? Post all codes.
Doubt software. If pressure is low its low.
May be timing chain as pump driven from camshaft.
Any misfire faults.
if you clear codes how do you get codes to come back.
how far you drive and how drive hard or normal.
Quote this message in a reply
17-10-2019, 17:27 PM,
Post: #9
RE: BMW F20 116i DME Update
It's the power supply module in engine room.

[Image: 61_3621.jpg?v=06.2019]

unable power voltage supply make fuel pump have unstable fuel pressure.
Quote this message in a reply
17-10-2019, 17:43 PM, (This post was last modified: 17-10-2019, 17:45 PM by Dee67.)
Post: #10
RE: BMW F20 116i DME Update
(17-10-2019, 17:19 PM)interested Wrote:  Is fuel pressure the only code in dme? Post all codes.
Doubt software. If pressure is low its low.
May be timing chain as pump driven from camshaft.
Any misfire faults.
if you clear codes how do you get codes to come back.
how far you drive and how drive hard or normal.

Actually I have done head gasket job on it ..skimmed head and valves reseated.
Timing been checked and ok. I have no issue with it starting maybe bit lumpy for short while then settles down. I take it for a drive and most times it's ok then all of sudden it starts to hesitate and not wanting to accelerate and then warning comes on idrive 'power train malfunction'. If I then stop the car and turn off for a minute or so it will fire up and run normal with no warnings. When I put ISTA D
and diagnose.. it comes up with 'high pressure pump plausibility' error.

(17-10-2019, 17:27 PM)simonchs Wrote:  It's the power supply module in engine room.

[Image: 61_3621.jpg?v=06.2019]

unable power voltage supply make fuel pump have unstable fuel pressure.

Thank you for the diagram..any pointers to  what I should check for? Cheers
Quote this message in a reply


Possibly Related Threads…
Thread Author Replies Views Last Post
XZBMW Update ISTA at once 4.43.40 (ISTA Update Program) charlesjyw 34 6,446 Yesterday, 10:39 AM
Last Post: MINIGP1610
  need update & mod VIN from FRM ? ka_rai 7 183 25-03-2024, 01:06 AM
Last Post: armenh7
  For anyone having problem with ICOM NEXT FW update via ISTA+. ImmBoo 16 3,897 24-03-2024, 11:29 AM
Last Post: Twointje
XZBMW Update ISTA 4.39.20 SQLiteDBs Italian Language diman64 8 741 09-03-2024, 20:18 PM
Last Post: diman64
XZBMW Update VIN in VCM through esys TIGHTFIN 10 1,148 05-03-2024, 11:26 AM
Last Post: oros
XZBMW Solved ✔ Cic update on E series alsamaraee 16 784 28-02-2024, 11:38 AM
Last Post: alsamaraee
XZBMW Programming_ Changes with xx-xx I level update that are perceptible to the customer shawnsheridan 10 1,925 22-02-2024, 12:17 PM
Last Post: bmchicago
  VCX SE and ISTA D update software of ecus? Maikiu 16 793 21-02-2024, 14:07 PM
Last Post: olifisz
  Update for DDE Pentheus 3 248 09-02-2024, 05:35 AM
Last Post: Stratofortress
XZBMW TokenMaster Launcher 5.2 Update hayend 24 4,230 03-02-2024, 10:37 AM
Last Post: zero9

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content