Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
BMW F31 acc retrofit help
15-01-2022, 17:22 PM,
Post: #1
|
|||
|
|||
BMW F31 acc retrofit help
hello, I retrofitted the ACC on a BMW F31, the system works and there were some errors, I took the BMW to calibrate it, thinking that was the case, but it remains the same. it works for a while and then the error. anyone had a similar problem?
I read these faults with bimmerlink. 1C Integrated chassis management 3 errors 4827BF: LDM function HighLevel operational readiness ACC sensors 48002C: LDM function - high-level operational readiness brake control unit D01B2A: Signal error (actual position EPS, ID: AVL_PO_EPS) - Invalid 29 Dynamic stability control MK60 E5 3 errors 4809AB: Global power supply - external undervoltage D35A53: Signal error (actual steering angle front axle, ID: AVL_STEA_FTAX) qualifier D35A62: Signal error (lateral acceleration center of gravity, ID: ACLNY_MASSCNTR) - qualifier 5D Camera-based driver assist system 1 error E06C43: Signal Status_Availability_Kette_Bremsung received invalid or brake chain not available |
|||
21-01-2022, 21:08 PM,
(This post was last modified: 21-01-2022, 21:09 PM by Pedrom92.)
Post: #2
|
|||
|
|||
RE: BMW F31 acc retrofit help
Hello, faults with ista in attachment.
it says ACC misadjusted, but the same was calibrated by BMW. and 2 faults appear in the ICM. Any help? Thanks. |
|||
21-01-2022, 21:14 PM,
Post: #3
|
|||
|
|||
RE: BMW F31 acc retrofit help
Did properly Code everything? With SA Codes did you use?
Does ACC Sensor show up Correctly |
|||
21-01-2022, 21:36 PM,
Post: #4
|
|||
|
|||
RE: BMW F31 acc retrofit help
Yes, i code 5AS already fitt and add 5DF.
sometimes it is 1 or 2 days without fault and then the fault appears and does not call for a while. I flash DSC, ICM, FRR, KAFAS, FEM to same ilevel. I do not know what else to do. |
|||
21-01-2022, 22:33 PM,
Post: #5
|
|||
|
|||
RE: BMW F31 acc retrofit help
Did you replace your grill?
|
|||
22-01-2022, 00:09 AM,
Post: #6
|
|||
|
|||
RE: BMW F31 acc retrofit help
Yes. Normal bumper. Need put cover.
|
|||
22-01-2022, 07:57 AM,
Post: #7
|
|||
|
|||
RE: BMW F31 acc retrofit help
I would check the wiring. Had it on an G30 ones. Sensor went on and off. After 4 Hours searching i found a plug that was bad.
|
|||
22-01-2022, 10:07 AM,
Post: #8
|
|||
|
|||
RE: BMW F31 acc retrofit help
I will check. but if it was something in the wires you should receive an error message in the ista type disconnected no?
|
|||
22-01-2022, 15:24 PM,
Post: #9
|
|||
|
|||
RE: BMW F31 acc retrofit help
Did you correctly mount the acc radar bracket? Also if I remember correctly the lower bumper support is different with and without ACC where you put the bracket on. Has that been changed or not needed for your car?
|
|||
22-01-2022, 16:56 PM,
Post: #10
|
|||
|
|||
RE: BMW F31 acc retrofit help
yes it had to be changed too.
|
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content