[Mastahh]

Hello,

Just received my VCP cable.
I used it to flash my 44: Steering Assist, and now I need to upload Parameters, but VCP only offers for "4G0 909 144L" and when I transfer it, i get error, failed.
Maybe after Flash I need to Reset all values and Learnings and then transfer parameters?

Before I was using Odis E and with Odis all these worked perfect.

I'm waiting for VCP answer, but not sure how long it will takes.

Maybe I'm doing something wrong.

I have following error on my Steering and firmware update fixes it for 1-2 weeks. So I can use car, but yes I plan to visit service. To fix permanently this issue.

Code:

    Address 44: Steering Assist       Labels: 4G0-909-144.clb

Control Module Part Number: 4G0 909 144 AA    HW: 4G0 909 144 G
  Component and/or Version: RCEPS         H40 0013
           Software Coding: 101000010000
            Work Shop Code: WSC 02391 785 00200
              ASAM Dataset: EV_RCEPS 009013 (AU57)
                       ROD: EV_RCEPS_009.rod
                      VCID: 68DF0DA79373D2CB6B-803C
1 Fault Found:

7353984 - Position Sensor for Motor
          C10AD 07 [137] - Mechanical Failure

[nirvananils]

You can't use Index L dataset for Index AA Software! You'll need Dataset for this Version

[Mastahh]

It is my second Flash to AA, first time I did it using Odis E and was able to upload "4G0909852H"
Same parameters as was before updating firmware.
But now I did flashing using VCP and it not so good as was with ODIS E
Now for AA I need to find proper parameters, not old ones?

Code:

Address 44: Steering Assist
Control Module Part Number: 4G0 909 144 L
  Component and/or Version: RCEPS         H40 0010
           Software Coding: 101000010000
            Work Shop Code: WSC 02391
                      VCID: 326BAFCF652F681B05-8066

Advanced Identification/FAZIT
     Serial number: 0009298686
     Identification: TT1-000
     Revision: 00001000
     Date: 09.02.14
     Manufacturer number: 0003
     Test stand number: 2710
Flash Status
     Programming Attempts(application): 0/0/0/0/0/0
     Programming Attempts(data): 1
     Successful Attempts(data): 1
     Programming Status: 00000000
     Flash Date: 14.02.09
     Flash Tool Code(data): 00200 785 02391
Misc.
     Hardware number: 4G0 909 144 G
     Workshop System Name: J500
     Equipment/PR Code: 000000000000000000001411
     Dataset Number: 4G0909852H
     Dataset Version: 0027
     End of Line Equipment Level: A39S----------------
     ASAM Dataset: EV_RCEPS
     ASAM Dataset Revision: 009008
Car Info
     Engine code: ----
VCDS Info:
       VCID: 326BAFCF652F681B05-8066
       Labels: 4G0-909-144.clb
       ROD: EV_RCEPS_009.rod

[Dana]

I think you will have to go back to Odis on 4G0909144L 0010 bottles.
In my opinion AA does not fit to this steering gear.

[Mastahh]

I only found TPI 2032205/8, that offers to update it to version 0012 (FL_4G0909144S)
But all forums update it to version 0013.
There are confirmation from someone, that he got flashed it by dealer from "4G0909144L 0010" to "4G0909144AA 0013"
I'm 100% sure that AA is OK for this, only problem with VCP, it cannot upload parameters for it.
I think that I will take VAS 5054A and upload parameters.

VCP support - already few days silence. Will be looking for good ODIS cable.

[Dana]

If you know that for sure then ok.
Do I understand correctly that you want to flash from servo motor on the steering gear to without motor?

[Mastahh]

If you know that for sure then ok.
Do I understand correctly that you want to flash from servo motor on the steering gear to without motor?

I just want to upload correct parameters for my Steering Rack