Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

VCP and Steering Assist parameters for 4G0 909 144 G
12-04-2022, 14:27 PM,
Post: #1
ZTAudi  VCP and Steering Assist parameters for 4G0 909 144 G
Hello,

Just received my VCP cable.
I used it to flash my 44: Steering Assist, and now I need to upload Parameters, but VCP only offers for "4G0 909 144L" and when I transfer it, i get error, failed.
Maybe after Flash I need to Reset all values and Learnings and then transfer parameters?

Before I was using Odis E and with Odis all these worked perfect.

I'm waiting for VCP answer, but not sure how long it will takes.

Maybe I'm doing something wrong.

I have following error on my Steering and firmware update fixes it for 1-2 weeks. So I can use car, but yes I plan to visit service. To fix permanently this issue.

Code:
    Address 44: Steering Assist       Labels: 4G0-909-144.clb

Control Module Part Number: 4G0 909 144 AA    HW: 4G0 909 144 G
  Component and/or Version: RCEPS         H40 0013
           Software Coding: 101000010000
            Work Shop Code: WSC 02391 785 00200
              ASAM Dataset: EV_RCEPS 009013 (AU57)
                       ROD: EV_RCEPS_009.rod
                      VCID: 68DF0DA79373D2CB6B-803C
1 Fault Found:

7353984 - Position Sensor for Motor
          C10AD 07 [137] - Mechanical Failure


Quote this message in a reply
13-04-2022, 08:03 AM,
Post: #2
RE: VCP and Steering Assist parameters for 4G0 909 144 G
You can't use Index L dataset for Index AA Software! You'll need Dataset for this Version
Quote this message in a reply
13-04-2022, 08:23 AM,
Post: #3
RE: VCP and Steering Assist parameters for 4G0 909 144 G
It is my second Flash to AA, first time I did it using Odis E and was able to upload "4G0909852H"
Same parameters as was before updating firmware.
But now I did flashing using VCP and it not so good as was with ODIS E
Now for AA I need to find proper parameters, not old ones?
Code:
Address 44: Steering Assist
Control Module Part Number: 4G0 909 144 L
  Component and/or Version: RCEPS         H40 0010
           Software Coding: 101000010000
            Work Shop Code: WSC 02391
                      VCID: 326BAFCF652F681B05-8066

Advanced Identification/FAZIT
     Serial number: 0009298686
     Identification: TT1-000
     Revision: 00001000
     Date: 09.02.14
     Manufacturer number: 0003
     Test stand number: 2710
Flash Status
     Programming Attempts(application): 0/0/0/0/0/0
     Programming Attempts(data): 1
     Successful Attempts(data): 1
     Programming Status: 00000000
     Flash Date: 14.02.09
     Flash Tool Code(data): 00200 785 02391
Misc.
     Hardware number: 4G0 909 144 G
     Workshop System Name: J500
     Equipment/PR Code: 000000000000000000001411
     Dataset Number: 4G0909852H
     Dataset Version: 0027
     End of Line Equipment Level: A39S----------------
     ASAM Dataset: EV_RCEPS
     ASAM Dataset Revision: 009008
Car Info
     Engine code: ----
VCDS Info:
       VCID: 326BAFCF652F681B05-8066
       Labels: 4G0-909-144.clb
       ROD: EV_RCEPS_009.rod


Quote this message in a reply
13-04-2022, 21:34 PM,
Post: #4
RE: VCP and Steering Assist parameters for 4G0 909 144 G
I think you will have to go back to Odis on 4G0909144L 0010 bottles.
In my opinion AA does not fit to this steering gear.


Quote this message in a reply
14-04-2022, 06:13 AM,
Post: #5
RE: VCP and Steering Assist parameters for 4G0 909 144 G
I only found TPI 2032205/8, that offers to update it to version 0012 (FL_4G0909144S)
But all forums update it to version 0013.
There are confirmation from someone, that he got flashed it by dealer from "4G0909144L 0010" to "4G0909144AA 0013"
I'm 100% sure that AA is OK for this, only problem with VCP, it cannot upload parameters for it.
I think that I will take VAS 5054A and upload parameters.

VCP support - already few days silence. Will be looking for good ODIS cable.


Quote this message in a reply
14-04-2022, 17:31 PM,
Post: #6
RE: VCP and Steering Assist parameters for 4G0 909 144 G
If you know that for sure then ok.
Do I understand correctly that you want to flash from servo motor on the steering gear to without motor?


Quote this message in a reply
18-04-2022, 06:47 AM,
Post: #7
RE: VCP and Steering Assist parameters for 4G0 909 144 G
(14-04-2022, 17:31 PM)Dana Wrote:  If you know that for sure then ok.
Do I understand correctly that you want to flash from servo motor on the steering gear to without motor?

I just want to upload correct parameters for my Steering Rack


Quote this message in a reply


Possibly Related Threads…
Thread Author Replies Views Last Post
ZVW Search for DCC 5Q0907376B Dataset/Parameters Asmir0000 0 28 Yesterday, 16:36 PM
Last Post: Asmir0000
ZTAudi parameters of the steering rack Audi A6C8 4N0909144E from RS VAGPRODRIVE 1 220 Yesterday, 13:19 PM
Last Post: Artem2287096
ZTAudi A3 8V Steering Light Amber gmc1103 4 87 04-05-2024, 17:26 PM
Last Post: virgo79
  Can someone help me flash the parameters of the camera? glljh2016 3 144 29-04-2024, 07:27 AM
Last Post: wanglejin
ZVW PLA3.0 Parameters please silentvox 7 963 22-04-2024, 03:34 AM
Last Post: Cur1mb4
  Audi 1.8 2009 need online support for coding steering angle sensor roanoke 2 116 13-04-2024, 03:10 AM
Last Post: DSESET86
  MQB A0 steering Rack software virgo79 1 153 11-04-2024, 22:58 PM
Last Post: zvonexp
  2018 Audi A8 help to flash A5: Frt Sens. Drv. Assist (J1121) deutsch 2 167 11-04-2024, 11:00 AM
Last Post: spooky75
  How to identify flash file name for each steering assist anass_f 2 150 28-03-2024, 13:24 PM
Last Post: anass_f
  4M0909144B Power Steering Rack skens 7 334 15-03-2024, 07:48 AM
Last Post: audi666

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content