Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
G20 new BDC and DDE
16-04-2022, 16:25 PM,
Post: #1
|
|||
|
|||
G20 new BDC and DDE
Hey,
I got on my hands 318d G20 from 03.2020 with new BDC from dealer. After replacing and coding, it turns out that DDE (D83BX7C0) is dead. Got an used DDE and then I shiped to tunner to make a clone. Not sure if he did proper job on it, since I can't start the car and ISTA gives me: EWS authentic response not received 276f00 error -The fault is logged if the DDE control unit receives an invalid rolling code from the CAS/FEM/BDC control unit. Any suggestion how to tackle this since DDE replacement is quite new to me ? Cheers! |
|||
16-04-2022, 16:40 PM,
Post: #2
|
|||
|
|||
RE: G20 new BDC and DDE
same ECU numbers ?
|
|||
16-04-2022, 23:24 PM,
Post: #3
|
|||
|
|||
RE: G20 new BDC and DDE
I do not understand how after coding bdc the engine ecu died? what faults ista shows.
• EGS7/7DCT300 ISN RESET REMOTE •
• KaFAS4 (MID/HIGH) MRR, RAM VIRGIN REMOTE • • NBTevo/ENTRYNAV2/MGU VIRGIN/PATCH • • HDD -> SSD NBT/NBTevo/MGU • CARPLAY NBTevo/EN2/MGU • • FULL FSC PATCH/RETROFIT CIC, EN2,NBT, NBT2, MGU, • • REMOVE CP --> NBTEVO ID4&6/Entrynav2/MGU • UK BASED! |
|||
17-04-2022, 04:35 AM,
Post: #4
|
|||
|
|||
RE: G20 new BDC and DDE
(16-04-2022, 23:24 PM)DEJMIEN Wrote: I do not understand how after coding bdc the engine ecu died? what faults ista shows. i think that not after codings, but he realized that alsodde was dead. i think flood car, first replaced bdc, when saw another dead ecu BMW FSC RETROFIT PACK: CIC / NBT / NBTevo ID4/5/6 entryevo
Carplay NBTEVO, ENTRYEVO, MGU MAPS codes for maps: Premium - Motion - Move - Route - Next - Evo - Way Best prices PM |
|||
17-04-2022, 07:51 AM,
(This post was last modified: 17-04-2022, 07:53 AM by diagso.)
Post: #5
|
|||
|
|||
RE: G20 new BDC and DDE
(16-04-2022, 16:40 PM)MaxBmw Wrote: same ECU numbers ? Yes, same exact part numbers (16-04-2022, 23:24 PM)DEJMIEN Wrote: I do not understand how after coding bdc the engine ecu died? what faults ista shows. Never said that DDE died after coding, there was a reason that BDC was replaced As you might know without this module working you can forget about any ISTA diagnostics. (17-04-2022, 04:35 AM)PsevDo Wrote:(16-04-2022, 23:24 PM)DEJMIEN Wrote: I do not understand how after coding bdc the engine ecu died? what faults ista shows. you are correct mate |
|||
17-04-2022, 11:22 AM,
Post: #6
|
|||
|
|||
RE: G20 new BDC and DDE
Do you have the 2 EEPROM from the original and used
|
|||
17-04-2022, 12:43 PM,
Post: #7
|
|||
|
|||
RE: G20 new BDC and DDE
Dme part numbers is same, where is cant be any problems
If ecu was dead, did wcu communicate on bench? If not, when ecu cannot be cloned, only with swapping cpu from ori to donor Seems like isn is wrong now BMW FSC RETROFIT PACK: CIC / NBT / NBTevo ID4/5/6 entryevo
Carplay NBTEVO, ENTRYEVO, MGU MAPS codes for maps: Premium - Motion - Move - Route - Next - Evo - Way Best prices PM |
|||
19-04-2022, 04:33 AM,
Post: #8
|
|||
|
|||
RE: G20 new BDC and DDE
This seems like a cloning issue.
|
|||
21-04-2022, 05:22 AM,
Post: #9
|
|||
|
|||
RE: G20 new BDC and DDE
(16-04-2022, 16:25 PM)diagso Wrote: Hey, Try initial flexray, and check ports |
|||
21-04-2022, 07:13 AM,
Post: #10
|
|||
|
|||
RE: G20 new BDC and DDE
(16-04-2022, 16:25 PM)diagso Wrote: Hey, can be done remotely REMOTE RESET 6HP & 8HP DKG M3 M4 M5 M6 E/F/G SERIES
REMOTE READING ISN {SK} E/F/G SERIES MSX8X,MG1,MD1 MEVD172X,EDC16/17 REMOTE CHIP-TUNNING E/F/G SERIES REMOTE RESET WORKING HOURS MEVD,MG1,MD1 REMOTE CODING & PROGRAMMING BMW/MINI-COOPER/ROLLS ROYCE FSC CIC/NBT/NBT EVO/MGU ID7 ID8 NCD CODING 2.0 CAS 1,2,3,4,FEM/BDC REMOTE PROGRAMMING SKYPE rus007777 WhatsApp +37455206005 |
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
2 Guest(s)
2 Guest(s)
Return to TopReturn to Content