Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Solved ✔ F22 front pdc retrofit issue
27-06-2022, 19:05 PM,
Post: #1
|
|||
|
|||
F22 front pdc retrofit issue
Hi,
Trying to retrofit front pdc at F22 but get faults aboute signal line disconect for all 4 sensors. Already check connection to rem and are ok. Also voltage are ok. I dont twist wiring - could be because of that? Also I route wiring near this big power supply cables - could be because of that? Rem are coded. I dont install addition button for pdc on consol, I dont code icm with 508 option, but I think this is not because of that... Few months back i retrofit rear pdc without problem. At this time rem was changed to work with rear and front pdc. Thank you If I helped, please magic buttons thx+rep
|
|||
27-06-2022, 20:37 PM,
Post: #2
|
|||
|
|||
RE: F22 front pdc retrofit issue
Are the sensors OEM or something else?
|
|||
27-06-2022, 20:41 PM,
Post: #3
|
|||
|
|||
RE: F22 front pdc retrofit issue
If I helped, please magic buttons thx+rep
|
|||
28-06-2022, 19:42 PM,
Post: #4
|
|||
|
|||
RE: F22 front pdc retrofit issue
Today I install and make wiring for pdc button in centre consol but problem still exists. Coded icm with one value (508 somethink), button work.
Also I swap sensors with brand new but not oem - no luck. Is there any function for reset this sensors? Check one more time both wiring- installed in car and bumper and everythink is ok. Tomorow I ran new wiring outside the car and check if this help. If I helped, please magic buttons thx+rep
|
|||
28-06-2022, 22:03 PM,
Post: #5
|
|||
|
|||
RE: F22 front pdc retrofit issue
Code rem, headunit.
|
|||
29-06-2022, 04:41 AM,
Post: #6
|
|||
|
|||
RE: F22 front pdc retrofit issue
I think rem is coded ok. I code it like this:
A_HYSTERESE = wert_02 D_SCHWELLE_1 = wert_02 D_SCHWELLE_2 = wert_02 V_SCHWELLE_1 = wert_02 V_SCHWELLE_2 = wert_02 PDC_VARIANT = wert_02 Hu also with: PDC_SENSOR_VORN = 4_sensoren This values are from esysx calculation option, always use this tool and never had any problems. Do I need additional coding? If I helped, please magic buttons thx+rep
|
|||
29-06-2022, 06:05 AM,
Post: #7
|
|||
|
|||
RE: F22 front pdc retrofit issue
Code ICM, HU, FEM, REM with option 508
|
|||
29-06-2022, 15:55 PM,
Post: #8
|
|||
|
|||
RE: F22 front pdc retrofit issue
Hi,
Coded REM to series but no luck - same faults. But I think I found reason of this. Based on no. installed sensors are from E series - e60 etc. The plug is same. I swap one sensor from rear bumper to front and dont have fault on this specific line. So I decide to order set of correct front sensors and will write back if that help.. If I helped, please magic buttons thx+rep
|
|||
02-07-2022, 20:04 PM,
Post: #9
|
|||
|
|||
RE: F22 front pdc retrofit issue
Hi, sensors replaced. Everythink working
If I helped, please magic buttons thx+rep
|
|||
« Next Oldest | Next Newest »
|
Possibly Related Threads… | |||||
Thread | Author | Replies | Views | Last Post | |
BMW CIC PATCHER v2 - GENERATE YOUR OWN RETROFIT FSC CERTS | intel123 | 891 | 465,209 |
3 hours ago Last Post: fe7565 |
|
G82 rear tail lights CSL retrofit | Sauron | 9 | 633 |
9 hours ago Last Post: juo |
|
Kafas issue aftrer ACC Retrofit | It3_Magic | 12 | 330 |
17-04-2024, 15:07 PM Last Post: user_530d |
|
Neck warmer retrofit | Just2fast5 | 5 | 340 |
17-04-2024, 11:20 AM Last Post: Spirit5676 |
|
TMS FRM3 F10 Coding issue | mj_mj_mj | 17 | 1,897 |
16-04-2024, 09:30 AM Last Post: user_530d |
|
ID4 evo to ID6 Evo full retrofit, ATM issues 03178A | mitch32 | 1 | 147 |
15-04-2024, 17:52 PM Last Post: mitch32 |
|
Bmw G31 retrofit Mgu id7 atm problem | intranet | 19 | 2,268 |
15-04-2024, 09:21 AM Last Post: evaldazj |
|
BMW E84 Cruise control retrofit not workig | Alyn546 | 4 | 207 |
12-04-2024, 14:23 PM Last Post: DieStream |
|
F10 FLA retrofit | beng2k | 30 | 996 |
11-04-2024, 18:43 PM Last Post: beng2k |
|
EBA PDC Front and rear F31 LCI | gvitkis | 1 | 78 |
10-04-2024, 21:54 PM Last Post: dumitru.o |
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content