Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

F & G series - Slow programming speed
01-07-2022, 15:16 PM,
Post: #1
XZBMW  F & G series - Slow programming speed
Hi! 
I'm programming an G30 right now using E-sys and Enet (but had same problem using E-sys with ICOM or Ista with Icom) and most of the modules went really fast as they should but then when it came to Dkombi and TCB it slowed down A LOT. I guess esys switched from Ethernet to D-Can but why? I had such situations sometimes with NBT and it took ages to programm it. 

Right now Windows Task Manager shows me 32kb/s of upload via Ethernet...

Where could be the problem? Is it something wrong with esys or maybe it's firewall related? I double checked and firewall is disabled. Using enet cable I'm sure its not router related problem because I don't use it.
Quote this message in a reply
01-07-2022, 16:33 PM,
Post: #2
RE: F & G series - Slow programming speed
Maybe you are flashing via UDS?
Quote this message in a reply
01-07-2022, 16:38 PM,
Post: #3
RE: F & G series - Slow programming speed
Yes, right now it seems its using UDS. But why other modules went via Ethernet and Esys switched on its own to UDS? How can I avoid this in future?
Quote this message in a reply
01-07-2022, 17:01 PM,
Post: #4
RE: F & G series - Slow programming speed
Firewall, Antivirus, wrong Configuration.

I have flashed with ISTA and ENET, but use DHCP-Router (software) and disable Antivirus/Firewall.

iLean offline license (PM)
FeatureCodes CarPlay (PM)
FSC-Generator
Quote this message in a reply
[+] 4 users say Thank You to Sedoy for this post
01-07-2022, 17:03 PM,
Post: #5
RE: F & G series - Slow programming speed
When I used esys 3.32 everything was fine but when I installed esys 3.36 it started using UDS all the time but when flash nbt / evo goes normally over HTTP. Flash via UDS in 3.36 is not that slow as was in version 3.32 it was very slow…

• EGS7/7DCT300 ISN RESET REMOTE •
• KaFAS4 (MID/HIGH) MRR, RAM VIRGIN REMOTE •
• NBTevo/ENTRYNAV2/MGU VIRGIN/PATCH •
• HDD -> SSD NBT/NBTevo/MGU
• CARPLAY NBTevo/EN2/MGU •
• FULL FSC PATCH/RETROFIT CIC, EN2,NBT, NBT2, MGU, •
• REMOVE CP --> NBTEVO ID4&6/Entrynav2/MGU •
UK BASED!
Quote this message in a reply
[+] 1 user says Thank You to DEJMIEN for this post
01-07-2022, 17:49 PM,
Post: #6
RE: F & G series - Slow programming speed
(01-07-2022, 17:01 PM)Sedoy Wrote:  Firewall, Antivirus, wrong Configuration.

I have flashed with ISTA and ENET, but use DHCP-Router (software) and disable Antivirus/Firewall.
Firewall totally disabled and no antivirus. Which configuration do you mean? ESYS?
Tried with original Icom via Router or even using build in DHCP server and still sometimes had this issue.

(01-07-2022, 17:03 PM)DEJMIEN Wrote:  When I used esys 3.32 everything was fine but when I installed esys 3.36 it started using UDS all the time but when flash nbt / evo goes normally over HTTP. Flash via UDS in 3.36 is not that slow as was in version 3.32 it was very slow…
Interesting. I'm using right now 3.36.2 and EsysX launcher so maybe I will give a try another version.

EDIT: Another question by the way. When I can and when I can't use Stop button in Tal Processing tab when programming is on?
Quote this message in a reply
01-07-2022, 18:44 PM,
Post: #7
RE: F & G series - Slow programming speed
Dont use launcher when programing
Quote this message in a reply
[+] 1 user says Thank You to Duken for this post
01-07-2022, 20:26 PM,
Post: #8
RE: F & G series - Slow programming speed
(01-07-2022, 17:49 PM)Krysiaman Wrote:  
(01-07-2022, 17:01 PM)Sedoy Wrote:  Firewall, Antivirus, wrong Configuration.

I have flashed with ISTA and ENET, but use DHCP-Router (software) and disable Antivirus/Firewall.
Firewall totally disabled and no antivirus. Which configuration do you mean? ESYS?
Tried with original Icom via Router or even using build in DHCP server and still sometimes had this issue.


(01-07-2022, 17:03 PM)DEJMIEN Wrote:  When I used esys 3.32 everything was fine but when I installed esys 3.36 it started using UDS all the time but when flash nbt / evo goes normally over HTTP. Flash via UDS in 3.36 is not that slow as was in version 3.32 it was very slow…
Interesting. I'm using right now 3.36.2 and EsysX launcher so maybe I will give a try another version.

EDIT: Another question by the way. When I can and when I can't use Stop button in Tal Processing tab when programming is on?

You can use stop button but the transactions that are being executed will continue.

I really don't understand the rush to use latest esys/ista d/p versions... latest doesnt mean better usage etc...
Quote this message in a reply
[+] 2 users say Thank You to jaramillo for this post
02-07-2022, 04:54 AM,
Post: #9
RE: F & G series - Slow programming speed
(01-07-2022, 18:44 PM)Duken Wrote:  Dont use launcher when programing

Doesn't matter.

So, the idea is this :
When u do BTLD it needs to go via UDS.
Then when it switches to SWFL or iba (case of evo) it will go to HTTP not HTTPS (it's not encrypted lol)

Try to edit the tal and force the Protocol to http

   

Or you can edit the tal.txt file and add this line

<swDeployTA preferredProtocol="HTTP" flashFileSize="0" estimatedExecutionTime="0" status="Executable">

Cheers!

Creator of FlashXTool v8 - link
CarPlay activations on Entrynav2 and NBTevo units
...more on FlashXCode.com

Whatsapp : +40741888845


Quote this message in a reply
[+] 2 users say Thank You to flashxcode for this post
04-07-2022, 08:35 AM,
Post: #10
RE: F & G series - Slow programming speed
Thank you guys! Tried all the tips and still got this: 

Code:
<MCDDiagService<id=285200, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=RDBI_IPCONF - ReadDataByIdentifier IPConfig, description=error: positive response with negative content: Subnet mask does not match with subnet mask of master gateway, link=HU_NBT2_63_ETHERNET> [DIAGSERVICE]>

<[] Activate programming mode was not successful for: ECUId:HU_NBT2_0x63 [WARN]>
<[] ECUId:HU_NBT2_0x63 not accessible cause could not be switched to parallel programming mode [WARN]>
<[HU_NBT2 - 63] ECUId:HU_NBT2_0x63 not accessible cause could not be switched to parallel programming mode [THROWABLE]>
<[] ECUId:HU_NBT2_0x63 not accessible cause could not be switched to parallel programming mode [WARN]>

Using I-COM, Esys 3.40 without launcher and edited TAL to force HTTP programming
Quote this message in a reply
[+] 1 user says Thank You to Krysiaman for this post


Possibly Related Threads…
Thread Author Replies Views Last Post
  Making F-series combox work in e-series Ryn079 0 109 23-03-2024, 19:44 PM
Last Post: Ryn079
  mileage g series virtual bosch id7 tigre 2 213 22-03-2024, 13:00 PM
Last Post: tigre
ZSkoda Solved ✔ ISTA Standalone WLAN programming botho 4 325 21-03-2024, 11:13 AM
Last Post: botho
XZBMW G Series KEY in F34 Rajco 5 358 20-03-2024, 18:56 PM
Last Post: Rajco
XZBMW F15 Programming Error mcrussell 7 389 20-03-2024, 05:38 AM
Last Post: SweetBMW
XZBMW BMW X6 E71 Programming Ryzen 5 194 16-03-2024, 12:42 PM
Last Post: Node
XZBMW G20 Speed Limiter? bmchicago 1 109 06-03-2024, 18:37 PM
Last Post: Node
XZBMW Solved ✔ Cic update on E series alsamaraee 16 787 28-02-2024, 11:38 AM
Last Post: alsamaraee
XZBMW ISTA/P is no longer supported for F, G & I series see_you_33 22 5,165 20-02-2024, 04:49 AM
Last Post: Alenorm
XZBMW problem with flashing CHAMP2 module (the programming dependencies are not correct) azwgh 17 661 11-02-2024, 19:39 PM
Last Post: azwgh

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content