Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

[RESTARTED] icom next clone repair (only single pcb)
08-01-2023, 21:57 PM,
Post: #1
[RESTARTED] icom next clone repair (only single pcb)
I want to restart a thread that was lost after the db recovery. These informations belongs to Ferrum, it's not my work. May this can be useful to someone that has a icom clone single pcb version, this thread is only related to icom with single pcb. If Ferrum would like to give suggestions here i'd be really happy.




Due to wrong assebly by chinese production, check all this:


swap

R292<->R293

R155<->R156

R178<->R179


check or change

R15  52ohm

R119  1k

R280 R285 R195  38k

Y4  33000 3.3v

R233  62k (r233 can be left unchanged. R233 installed 47k and should be 62k but this is not critical)

R178 100k

R179 1.4k

R156 72ohm

R292 72ohm

R155 1K

R293 1K




other infos in attachments.


Attached Files Thumbnail(s)
                               
change serial.pdf
File Type: .pdf
Downloaded: 173 times
Size: 3.58 MB

ICOM2 restore+serial.zip
File Type: .zip
Downloaded: 104 times
Size: 12.92 MB


[Image: GIF-Bandiera-Italiana.gif]
Reputation: +7 - AZCKNCLLC [+1] , jaramillo [+1] , huk_00 [+1] , paui [+1] , Verado400M [+1] , al70 [+1] , _villi_ [+1]
Quote this message in a reply
[+] 10 users say Thank You to ____ANGEL___ for this post
09-01-2023, 19:19 PM, (This post was last modified: 09-01-2023, 19:40 PM by ferrum.)
Post: #2
RE: [RESTARTED] icom next clone repair (only single pcb)
Now in the Chinese market, 3 varieties are sold with different errors. Only one R119 error is repeated in all clones. There are clones in which the quartz is set at the correct frequency of 33000 but it has other critical errors.

Not everyone needs to change places
R292<->R293
R155<->R156
Not everyone needs
R15  52ohm
Y4  33000 3.3v
Some added other errors that are not described here.
If your icom board has R15 52ohm then this guide does not fully address the fixes that need to be done


Attached Files Thumbnail(s)
       
Reputation: +6 - jaramillo [+1] , zeronoo [+1] , izm [+1] , huk_00 [+1] , paui [+1] , al70 [+1]
Quote this message in a reply
[+] 6 users say Thank You to ferrum for this post
06-02-2023, 14:01 PM,
Post: #3
RE: [RESTARTED] icom next clone repair (only single pcb)
Small PCB with switch must be done by me to make ICOM restore?
Quote this message in a reply
06-02-2023, 15:23 PM,
Post: #4
RE: [RESTARTED] icom next clone repair (only single pcb)
(06-02-2023, 14:01 PM) MIKUr1 Wrote:  Small PCB with switch must be done by me to make ICOM restore?

Yes, you are right. 

   


Quote this message in a reply
06-02-2023, 20:00 PM,
Post: #5
RE: [RESTARTED] icom next clone repair (only single pcb)
The restore function is extremely rarely needed, since in most cases it is associated with the repair and replacement of microcircuits. I don't install the board and only use it when I need it.

If you need a restore button, I drew a diagram that is understandable even to a non-repair specialist and it is quite easy to reproduce it.

The contact going to the LM77 is a connection with 3.2v, it can be taken from another place.
Difficulties may arise when soldering to the 42nd leg of the mega16 and this must be done very carefully without damaging the microcircuit, since in the event of a breakdown, the mega16 can only be taken from the donor
Quote this message in a reply
06-02-2023, 20:51 PM,
Post: #6
RE: [RESTARTED] icom next clone repair (only single pcb)
Rarely needed, but without serial change and restore, ICOM will give fan error, am I right?
Quote this message in a reply
06-02-2023, 21:43 PM,
Post: #7
RE: [RESTARTED] icom next clone repair (only single pcb)
The button can be connected neatly without a bunch of wires


I make these wires myself, they fit clones and originals


Attached Files Thumbnail(s)
               
Reputation: +1 - jaramillo [+1]
Quote this message in a reply
07-02-2023, 12:54 PM,
Post: #8
RE: [RESTARTED] icom next clone repair (only single pcb)
One more question - I saw that some ICOM NEXT's have some cheaper versions, without one of port's - the round one with 5 pins. What is purpose of this port? There is no matching cable for it.
Quote this message in a reply
07-02-2023, 13:01 PM,
Post: #9
RE: [RESTARTED] icom next clone repair (only single pcb)
Imib oscilloscope

[Image: GIF-Bandiera-Italiana.gif]
Reputation: +1 - ctgy8923 [+1]
Quote this message in a reply
[+] 2 users say Thank You to ____ANGEL___ for this post
07-02-2023, 13:12 PM,
Post: #10
RE: [RESTARTED] icom next clone repair (only single pcb)
So I assume, that this port is not neccessary? Or there is some more differences?
Quote this message in a reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  [MEGA] Any ESYS Editions + PSDZ Full & Lite + ICOM Firmware + MANUALS + TOOLS hashtagmaster 102 34,755 Yesterday, 05:59 AM
Last Post: hashtagmaster
XZBMW Poor wifi signal from new ICOM's bmchicago 1 133 26-03-2024, 03:04 AM
Last Post: rocdeng
  E53 LCM Clone maninblack 10 252 25-03-2024, 14:03 PM
Last Post: Spitfire555
  For anyone having problem with ICOM NEXT FW update via ISTA+. ImmBoo 16 3,900 24-03-2024, 11:29 AM
Last Post: Twointje
XZBMW Request KAFAS FSC repair pack miru75 74 8,320 23-03-2024, 17:50 PM
Last Post: radeeek17
  TESTO tool with ICOM Rolzs 5 316 17-03-2024, 20:23 PM
Last Post: Vojno
  Request xHP 6HP decrypted files and icom flasher tste1982 10 828 05-03-2024, 22:47 PM
Last Post: bradsm87
  FRM repair and clone DME & DDE jaki 27 1,327 01-03-2024, 22:52 PM
Last Post: r0my81
XZBMW FRM3 F11 XEP100 need dump or repair 530d 2 141 22-02-2024, 15:33 PM
Last Post: 530d
XZBMW FEM MODUL CLONE arcelik 10 499 19-02-2024, 10:16 AM
Last Post: bm92

Forum Jump:


Users browsing this thread:
2 Guest(s)

Return to TopReturn to Content