[massilos]

Hi everyone I am having an issue with a BCM for Renault Trafic III 2015 the headlights not working, and the wipers is not working also Cranks but it doesn't start. 


I have a replacement BCM but  not been programmed. I would like to do the chip swap from one of the electronic shop. I attached the picture for the BCM board. What tchip that needs to be swap it from the board  to do the cloning, i aprecited your help.Thank you


i was reading in auther forum only talking about SPC560B54L ic ,i wanted to make sure we desolder the corect flash and eeprom for swaping any info are welcome

[CHIKODIAG]

HI
YOU CAN NOT SWAP BECAUSE IT HASE A SPC FLASH THE BEST WAY YOU VIRGIN THE NEW ONE AND ADAPT TO THE CAR
GOOD LUCK

[massilos]

Hi mate thank you for the advice too late for me now as I took the the two BCM Cilla local electronic shop they managed to swap the chip very clean job no I get another issue I use can clip v214.
DTC95f031. Transponder supply circuit
Also when I do UCH live data keys allocated to the vehicle. (NO)
Key code recognised by the vehicle (YES)
Blank key (NO)
I took it all the fuses tonight on all of them are ok I am wondering this responders supply circuits.
Also something very important they notice try to open the key the door lock the door with a remote control I can see the warning light comes on I could hear the BCM relay clicking on other doors are not locking or closing.

[massilos]

i noticed there is pin 8 and pin 9 are not soldered probably is the source of the problem i will keep you posted

[massilos]

Yes, there were a few pins that were not soldered properly, but we managed to sorted. The van still doesn't start central lock doesn't work either when you click the remote control you can hear the BCM relay clicks warning light comes on but the doors doesn't lock unlock the doors. Is probably something to do with transponder as i am getting DTC96F031 (transponder supply circuit) i tested the circut i get the 12v at the connection . i ODBlink SX brand new i updated the latest firewmaware also I get the renolink 1.99 and 2.05 but is not connecting via OBD I tried to scan no detection no communication i did folow the instruction I also to open the XML edc17c42 and connect but nothing works I just don't know why I tried in Windows 7pro 32 bit then tried in Windows 10pro 64 bits but Renolink doesn't seems to communicate via obd i can see the link of obdlink sx blinkining but no communication. As soon as I connect Can clip it works right away it detect the vin and scan everything I don't know why renolink is not working. Can clip cannot virginize the bcm. . But renolink yes can do. But not working

[diagservhaag]

Yes, there were a few pins that were not soldered properly, but we managed to sorted. The van still doesn't start central lock doesn't work either when you click the remote control you can hear the BCM relay clicks warning light comes on but the doors doesn't lock unlock the doors. Is probably something to do with  transponder as i am getting DTC96F031 (transponder supply circuit) i tested the circut i get the 12v at the connection . i  ODBlink SX brand new i updated the latest firewmaware also I get the renolink 1.99 and 2.05 but is not connecting via OBD I tried to scan no detection no communication i did folow the  instruction  I also to open the XML edc17c42 and connect but nothing works I just don't know why I tried in Windows 7pro  32 bit then tried in Windows 10pro  64 bits but  Renolink doesn't seems to communicate via obd i can see the link of obdlink sx blinkining but no communication. As soon as I connect Can clip it works right away it detect the vin and scan everything I don't know why renolink  is not working. Can clip cannot virginize the bcm. . But renolink yes can do. But not working

OBDlink should work with Renolink. Did you 'upgrade' the speed setting? I remember that I needed to upgrade the speed for the newer versions of Renolink... Maybe that is why you cannot communicate.
Do you have no connection with any ECU? None found when scanning the vehicle?

[massilos]

Hi every one ,we virginized the bcm to reprogrammed and now is requisting 39 digital code i get this number with it ,now the keys not working no more.any advice is appreciate Tahnk you

---

we try the pin code but not working

[massilos]

basically the van is dead